Installation Manual 20’W x 20’L x 8’H Premium Canopies Protective Weather Structures Inc. 5290 Orcutt Road San Luis Obispo, CA 93401 © 2011 - All Rights Reserved PWSsteelbuildings.
PWS has dedicated years of steel building knowledge and construction to create the highest quality canopy made today. With a little effort following the detailed instructions during assembly, this canopy will provide you with years of enjoyment and unparalleled protection. Contents Safety & Hazards Consideration................................4 Tools Required..............................................................4 Parts List........................................................................
Safety & Hazards Considerations • • • • • • • • • • • • • Check that all tools and canopy components are available prior to erecting structure. Two people are necessary to safely erect the canopy. Do not allow children to play around the assembly area. Protect yourself by wearing protective work gloves, hard hat, safety glasses, and shoes during assembly. Some parts have sharp edges which may cause cuts or lacerations.
Parts List Part # and Description ( 1 ) Long Base Rails ( 2 ) Base Rail Inserts ( 3 ) Short Base Rails ( 4 ) Columns ( 5 ) Roof Truss ( 6 ) Truss Crown Inserts ( 7 ) Cord Inserts ( 8 ) Purlins ( 9 ) Purlin Inserts ( 10 ) Insulation ( 11 ) Eve Trim ( 12 ) Roof Sheet Metal ( 13 ) J-Trim ( 14 ) Gable Sheet Metal Kits ( 15 ) Rake Trim Left ( 16 ) Rake Trim right ( 17 ) Ridge Cap 2 2 2 10 10 5 5 16 8 4 4 16 4 4 2 2 2 Frame Screw Sinker Screw Stitcher Screw Frame Screws – Regular Sinker Screws – Roof Color S
Long base Rail Column Inserts Short Base Rail Base Rail Insert Base rail assembly and Terminology PWS -Premier Canopies 1-888-547-8797 Page 5
Canopy Installation Site Preparation It’s important to have the site ready for the installation of the canopy. The frame is designed to be placed either onto a concrete foundation, anchored with concrete piers, or staked into the ground. There is likely more than one way to properly anchor the canopy, however, we provide three different options. Important: If a concrete slab is to be poured, preparing the ground by leveling and compacting may be necessary.
Foundation & Anchoring Option 1: Direct Staking The canopy is delivered with rebar stakes that can be used to either directly stake the canopy down into firm ground or in option 2 page 8 as an anchor for concrete piers. The Simplest method to anchor the canopy is to pound the supplied stakes into the ground with a hammer after the base rails are properly spaced. (See Positioning Base Rails below.
Option 2 : Anchoring to New Concrete Pier The second simplest method to anchor the canopy frame is to pour concrete piers. Layout the base rails per the previous instruction (see Positioning Base Rails page 7) and mark the locations where the Anchor Stake are to be located. Remove the base rails and dig each hole a minimum of 24” or down to the frost line, whichever is greater (fig 2).
Frame Assembly Left Truss Half Truss Rafter Eve End Truss Crown Insert Right Truss Half (photo 4) Column Insert Truss Face Truss Cord Cord Insert Roof Truss Assembly Step 1 - Verify the placement of the Base rail assemblys for squareness and correct rail separation. Tip: Laying the truss components at least 8 feet in front of the Base rails will help simplify the ease of assembly.
128” 85” 43” 3/4” (fig 4) Note: It is best to complete and raise one frame at a time. When rais- ing Roof Truss Assemblies, two people are necessary to lift the rafter and column assembly to place it. Face the screw heads towards the inside of canopy on both end rafters. Face screws to the back on the center frames. Step 5 - Begin installing Roof Truss Assembly at the farthest point on the base rails. Rest the end of the column against base rail column insert (photo 9).
Purlin Assembly Purlins Purlins (photo 11) Assembled Frame Step 1 - Each 20 foot purlin is shipped as two ten foot pieces (photo 12) and one insert. Begin by laying out the purlins next to the base rails on each side of the canopy. With the large holes facing up, slide the insert in so the hole in the insert lines up with the half hole on the purlin (photo 11). On the side install a frame screw 4“ back, then slide the other half of the purlin onto the insert and attach.
Insulation Insulation Note: It is not recommended to install the Insulation on a windy or breezy day as the adhesive will not likely hold in these conditions. Step 1 - Apply the double sided adhesive tape on top of both (photo 16) the outermost purlins from end to end as shown, leaving the tape cover on for now (photo 16). Step 2 - Place the first of 4 sheets of insulation over the canopy, white side facing down. The insulation will be several inches longer than need be on both sides.
(photo 18) (photo 19) Eve Trim Eve trim Step 1 - Begin installing the first Eve trim at the back of canopy frame working forward. Place trim on top of Insulation and end of rafter with drip edge down. Extend it past outside of rafter face 11/4” (photo 20)(fig 8 on page 14). Note: It’s very important to press down firmly to compress the insulation before fastening it down. Otherwise, when the roof sheet is installed, it will tend to cause it to deform.
Roof Sheet Roof sheeting Truss face Warning - Do not attempt to stand on roof panels that have not been attached. Step 1 - The placement of the first sheet is the most critical. J (photo 22) The sheet is not symmetrical and must be started as shown (photo 22) with the short overlap facing out. Make sure the sheet is square to the frame. It must be positioned a set disI tance from the outside truss face as well as from the eve trim (fig 8)(fig 9).
Note: Double check the 21/2” overhang and make sure the sheet is perpendicular to the purlins. The stitcher screws are only used to fasten sheet metal to sheet metal. Make sure the screws are the correct type and color. Step 2 - Follow the pattern below to fasten the sheet to the purlins (fig 9). Mark the location by measuring out where the screws go before lifting sheet onto the roof (photo 25).
Gable and J-trim Gable kit J-trim Step 1 - Align the bottom of the J-trim with the bottom of the truss cord and extend end of J-trim to eve trim (photo 27). Using frame screws, fasten the J-trim to the face of the truss in from each end 2”. These screws will be removed later. Repeat this step on the other side. This piece will sit inside the first J-trim piece in the center of the frame. Step 2 - The Gable kit comes in five pre-cut pieces per end.
Sinker Screws Screw Pattern - End Gables (fig 10) Stitcher Screws Sinker Screws Rake Trim Rake trim Step 1 - Locate the left side, uncut Rake trim, and position it as shown in (photo 30). If the roof sheet was fastened in the correct location, the top edge should line up directly in the middle of the peak, and the bottom edge should line up with the roof sheet.
(photo 32) (photo 33) Step 3 - Using the same color stitcher screws as the (photo 34) trim, the first screw should be into the face of the J-trim drilling through the edge of the rake trim as shown in (photo 32) and (photo 33). After verifying that everything is square and in place, fasten a sinker screw down through top edge of the rake trim and down through the roof sheet into the center of the purlin below. Continue on every purlin.
Ridge Cap Ridge Cap Note : The ridge cap attaches in two pieces. Be careful while handling, they can buckle which will leave an undesirable crease. Step 1 - Begin by laying the first ridge cap starting from the back. Align the ridge cap end even with the outside face of the rake trim (photo 37). Using color matched stitcher screws, attach through the edges of the ridge cap into the rake trim on both sides. Align the other end of the ridge cap with the center of roof ridge. Do not attach at this time.
R ev 82712 PWS - Premier Canopies 1-888-547-8797 Page 20
