DVR User Manual Recording System www.provision-isr.
Digital Video Recorder User Manual CAUTION Read this user manual carefully to ensure correct and safe use of your PROVISION-ISR DVR. The content of this manual could be outdated or incorrect, for any clarification contact PROVISION-ISR support. This device should be operated only from the type of power source indicated on the marking label. The voltage of the power must be verified before using. If you plan not to use the DVR for a long time, shutdown and unplug the power cable.
Digital Video Recorder User Manual Table of Contents 1 Introduction........................................................................................................................................................................................................... 1 1.1 DVR Introduction ....................................................................................................................................................................................... 1 2 Hardware Installation ........
Digital Video Recorder User Manual 2.3.13 Rear Panel Description (SA-8200SDI)......................................................................................................................................... 25 2.3.14Rear Panel Description (SA-16200SDI/SA-16400SDI) ................................................................................................................ 26 2.4 Remote Controller .....................................................................................................
Digital Video Recorder User Manual 4.3.4 Stamp ............................................................................................................................................................................................. 42 4.3.5 Recycle record ................................................................................................................................................................................ 43 4.3.6 Snap.............................................................
Digital Video Recorder User Manual 5.4 Image ........................................................................................................................................................................................................ 68 5.5 Backup ...................................................................................................................................................................................................... 68 6 Manage DVR .....................................
Digital Video Recorder User Manual Remote Information Search .................................................................................................................................................................... 88 8 Mobile Surveillance ............................................................................................................................................................................................ 89 8.1 iPhone/iPad app (SuperLivePro for iOS): .........................
Digital Video Recorder User Manual 1 Introduction 1.1 DVR Introduction Thesemodel DVRs (Digital Video Recorder) are designed specifically for CCTV system. The device contains highperformance video processing chips and an embedded Linux system, it utilizes advanced standard technologies, such as H.264 with low bit rate, Dual stream, SATA interface, VGA output mouse supported, IE browser supported with full remote control, mobile view(by phones) and more. All those ensure itssuperiorand stable performance.
Digital Video Recorder User Manual • Supports zoomX4 option during playback. BACKUP • • • • • SupportsUSB 2.0 devices for backup. Supports installation of a built-in SATA DVD writer for backup (not small 1U case DVR). Supportssaving recorded files with AVI standard format for a remote computer through internet. Supports import/export of definitions/settings. Supports E-mail Notification function with (or without) attached snapshot.
Digital Video Recorder User Manual PTZ CONTROL • • • Supportsmultiple PTZ protocols. Supports128 PTZ presets and 8 auto cruise tracks. Supportsremote PTZ control through internet. SECURITY • Usermanagement: log search, system setup, two way audio, file management, disk management, remote login, live view, manual record, playback, PTZ control and remote live view. • • • • Supports1 administrator and 63 usernames and linked passwords w/wo associated Mac address.
Digital Video Recorder User Manual 2 Hardware Installation Notice: Check the unit and the accessories after getting the DVR. shut down the device and unplug the power line before any new connections to other devices. Don't hot plug in/out Please note: Small1U case DVR: SA-16400N+, SA-8200N+, SA-4100HDE+, SA-4100HDX+ 1U case DVR: SA-16400NE+, SA-16400HD+, SA-8200HD+, SA-8200SDI, SA-4025SDI, SA-4100SDI, SA-24600 2U case DVR:SA-32800, SA8200D1SDI, SA-8200SDI, SA-16200SDI, SA-16400SDI 2.
Digital Video Recorder User Manual 2.1.2 Install the DVD Writer (1U DVR case) Notice: 1. The DVD writers must be on the compatible devices list. Please refer to “Appendix C Compatible Devices” 2. This device is only for backup Step1:unplug from the power line, then unscrew and carefully open the top cover Step2:Connect the power and data cables, and then place the DVD writer on the bottom case as Fig2.3. Step3:Secure the DVD writer using the appropriate screws (Fig2.4) Fig 2.3 DVD Writer placement Fig 2.
Digital Video Recorder User Manual 2.1.4 Install the Hard Drive(2U DVR case) Notice: 1. This series support four SATA hard drives or three SATA hard drives plus one DVD writer. (User can also choose to install eight SATA hard drives or four SATA hard drives plus one DVD writer. Here take eight SATA hard drives installation for example). Use the hard drive onthe compatible devices list. Please refer to “Appendix C Compatible devices”. 2. Please calculate HDD capacity according to the recording setting.
Digital Video Recorder User Manual Step 3:Install other three HDD according to above-mentioned method. Then cover the upper iron bar and screw it firmly.
Digital Video Recorder User Manual 2.1.5 Install the DVD Writer(2U DVR case) Step 1: Unscrew and open the case. Then unscrew the screws on both sides to remove the upper bar as shown below: Step 2: Install the DVD holder that came with the device. Please let the screw holes of the DVD aim and the bolts. Try to place the holder farther away from the front and then screw firmly. Then, put the DVD with the holder into the case and let the screw holes of the case aim at the holder’s.
Digital Video Recorder User Manual 2.2 Front Panel Descriptions: 2.2.1 Front Panel Description (1U DVR case): Item Type Work state indicator 1 Compound button 2 3 Digital button 4 Input button 5 6 7 IR receiver USB Extension Name Description Power HDD Net Backup Play REC MENU/+ BACKUP/RECORD/FOCUS REW/SPEED SEARCH/ZOOM PLAY /IRIS FF/ P.T.Z.
Digital Video Recorder User Manual 2.2.2 Front Panel Description(small 1U DVR case): Item Type Work state indicator 1 Compound button 2 Input button 3 4 5 6 IR receiver USB External IR Name Description Power HDD Net Backup Play REC MENU/+ BACKUP/RECORD/FOCUS REW/SPEED SEARCH/ZOOM PLAY /IRIS FF/ P.T.Z.
Digital Video Recorder User Manual 2.2.3 Front Panel Description (2U DVR case) Item Name 1 2 3 4 5 6 Power Button DVD button Keys 0-9 (0/——) AUDIO/+ P.T.Z./ Input button 7 Work state indicator 8 9 Function button Function Soft switch off to stop firmware running. Do it before power off. Press this button, user can place the DVD to do backup. Input number 1-9 or choose camera 1. represents decade number. 2. Indicates digital number 0 1. Control voice2. Increase the value in setup 1.
Digital Video Recorder User Manual Item 10 11 12 13 Name Function Jog dial USB port IR receiver External IR BACKUP Enter backup mode in live SEARCH Enter search mode REW Rewind FF Fast forward REC Record manually PLAY Play/Pause STOP Stop/Esc Control rewind/fast forward/frame when playing the image.
Digital Video Recorder User Manual 2.3 RearPanel Descriptions 2.3.
Digital Video Recorder User Manual 2.3.
Digital Video Recorder User Manual 2.3.3 Rear Panel Description (SA-8200N+) Item Name Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Audio in Video in Ground Audio out Video out Spot Power switch RS485 ALARM OUT ALARM IN HDMI VGA port LAN USB DC12V 4 CH Audio input Video input channels from 1-8 Grounding (also for the alarm in ground connection) Auxiliary audio output Connect to monitor Connect to monitor with no menu display ON/OFF switch Connect to speed dome (RS485 PTZ cameras) 1-ch relay output.
Digital Video Recorder User Manual 2.3.4 Rear Panel Description (SA-16400N+) Item Name Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Audio in Video in Ground Audio out Video out Spot Power switch RS485 ALARM OUT ALARM IN HDMI VGA port LAN USB DC12V 4 CH Audio input Video input channels from 1-16 Grounding (also for the alarm inground connection) Auxiliary audio output Connect to monitor Connect to monitor with no menu display ON/OFF switch Connect to speed dome (RS485 PTZ cameras) 1-ch relay output.
Digital Video Recorder User Manual 2.3.5 Rear Panel Description (SA-16400NE+) Item Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Power switch P/Z K/B Audio in Video out Video in VGA port FAN DC12V Ground ALARM IN Audio out Spot HDMI USB LAN ALARM OUT Description ON/OFF switch Connect to speed dome (RS485 PTZ cameras) Connect to keyboard 4 CH Audio input Connect to monitor Video input channels from 1-16 VGA output, connect to monitor Fan for ventilation, DO NOT COVER THE FAN.
Digital Video Recorder User Manual 2.3.6 Rear Panel Description(SA-8200HD+) Item Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Power switch P/Z K/B Audio in Audio out Spot Video out FAN DC12V Ground ALARM IN HDMI VGA port USB LAN Video in ALARM OUT Description ON/OFF switch Connect to speed dome (RS485 PTZ cameras) Connect to keyboard 4 CH Audio input Auxiliary audio output Connect to monitor with no menu display Connect to monitor Fan for ventilation, DO NOT COVER THE FAN.
Digital Video Recorder User Manual 2.3.7 Rear Panel Description(SA-8100SDI) Item Name 1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 ALARM OUT P/Z K/B Video out Audio out MIC IN Audio in Power switch FAN ALARM IN Video in HDMI VGA LAN USB DC12V Description 4-ch relay output.
Digital Video Recorder User Manual 2.3.
Digital Video Recorder User Manual 2.3.9 Rear Panel Description(SA-4100SDI) Item Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 ALARM OUT P/Z K/B Video out Audio out MIC IN Audio in Power switch FAN ALARM IN Ground Video in HDMI VGA LAN USB DC12V Description 4-ch relay output.
Digital Video Recorder User Manual 2.3.
Digital Video Recorder User Manual 2.3.11 RearPanel Description(SA-32800) Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15/16 17 18 19 20 21 Name Video out Video in POWER INPUT Loop Out (17-32) Loop Out (1-16) Spot MIC IN Description Connect to monitor Video input channels(1- 32-ch) 110VAC or 230VAC Video out (with a 16 channel plug) for channels 17-32. Video out (with a 16 channel plug) for channels 1-16.
Digital Video Recorder User Manual 2.3.
Digital Video Recorder User Manual 2.3.
Digital Video Recorder User Manual 2.3.
Digital Video Recorder User Manual 2.4 Remote Controller The remote requires two AAA size batteries. For installing the batteries open the battery cover onthe Remote Controller, placetwo batteries according to the correct polarity marked on the remote (+ and -), then fasten the battery cover to back its place. Notice: if the remote is not working follow those steps: 1. Check batteries poles are according to the marking inside the remote and check the remote. 2. Replace the batteries and check the remote.
Digital Video Recorder User Manual Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Name Power Button INFO Button REC Button Digital Button Multi-Screen Button SEARCH Button MENU Button ENTER Button Direction Button +/- Button Playback Control Button AUDIO Button Auto Dwell Button BACKUP Button PTZ Control Button Function Soft switch off to stop firmware running. Do it before power off.
Digital Video Recorder User Manual The "small 1U" DVR models contain the small remote controller.
Digital Video Recorder User Manual 2.5 Control with Mouse 2.5.1 Connect Mouse The DVR supports USB mouse through the ports on the rear panel, please refer to Fig2.8. Notice: If mouse is not detected or doesn't work: 1. Make sure the mouse is plugged to the correct USB mouse port not the USB port2. Replace the mouse 2.5.2 Use Mouse In live: Double-click (left button) on one camera screenfor full screen display. Double-click again to return to the previous screen display.
Digital Video Recorder User Manual 3.1 Power On/Off 3 Basic Function Instruction Before you power on the unit, please make sure all the cables are connected properly. 3.1.1 Power on Step1:Plug in thepower; switch on the power button (16-channel DVR only) Step2:The device will start loading, and the power indicator will have blue color.
Digital Video Recorder User Manual 3.2 Login You can login and logout from the DVR system. After logout the user cannot operate except changing the multi-screen display. Fig 3-1 Login Notice: The default user name is "admin" and the password is "123456” Tochange thepassword,or to add or deletea user refer to Fig 4.7 "User management configuration". 3.
Digital Video Recorder User Manual 3.3.1 Live playback Click Play button to playback recordings. Youcan change settings by clicking on the buttons on screen.
Digital Video Recorder User Manual 4 Main menu setup guide Click right mouse or press ESC button on the front panel: the control bar will appear on the bottom of the screen, refer to Fig 4-1: Fig 4-1 main menu toolbar Click the icon beside "screen mode" to selectthe channels. There is an option for 6/8/13 channels with a main channel in the middle of the screen. You canarrange the order by drag and dropfor the live display.
Digital Video Recorder User Manual Fig 4-2 main menu configuration menu 4.1 Basic configuration The basic configuration has three sub menus: system, date& time and DST. 4.1.1 System Step1: enter into system configuration=>basic configuration=>system; refer to Fig 4-3: Step2: in this interface you can setup the device name, device ID, video format, max network users, VGA resolution and language.
Digital Video Recorder User Manual Password check: enabling this option prompts user name and password before user can perform operations on the DVR. Show System time:displays the time in live view. Startup wizard:This option enables the wizardon startup. Max network uses: set the maximumsimultaneous users via network connection. VGA resolution: the resolution of live displayinterface, range from: VGA800*600, VGA1024*768, VGA1280*1024and CVBS.
Digital Video Recorder User Manual 4.1.3 DST System configuration=>basic configuration=>DST; refer to Fig 4-5: In this interface you can enable daylight saving time, set the DST time offset, mode, start & end month/week/date. Reset default setting; click the“default” button and then“apply” button to save the setting.Pressthe “exit” button to exit current interface. Fig 4-5 basic configuration-DST 4.2 Live configuration The live configuration has four submenus: live, host monitor, Spot and mask. 4.2.
Digital Video Recorder User Manual Fig 4-6 live configurationlive Fig 4-7 live-color adjustment Step3:clicking the“setting” button will pop-up a window(Fig 4-7) in this interface, you can adjust brightness, hue, saturation and contrast in live.The“default” button willrestore the DVR todefault live setting, click “OK” button to save the setting. Step4:you can setup all channels with same parameters bymarking“all”, and then"Apply". 4.2.
Digital Video Recorder User Manual Click button to set the next channel group. Step5: click “default” button to resort default setting; click “apply” button to save the setting; click “exit” button to exit current interface. 4.2.
Digital Video Recorder User Manual Setup mask area Live image mask area 4.3 Record configuration Record configuration includes six sub menus: enable, record bit rate, time, recycle record, stamp and snap for NE orHD series. 4.3.
Digital Video Recorder User Manual 4.3.2 Record stream Step1:go to system configurationrecord configurationrecord bit rate; refer to Fig 4-12: Step2: setup rate, resolution, quality, encode and max bit stream Step3: setup everychannel with the requiredparameters, or mark “All”and setto apply thechanges to all channels. Reset default setting; click the“default” button and then“apply” button to save the setting.Pressthe “exit” button to exit current interface.
Digital Video Recorder User Manual Expire time:the maximum time a recording will be in the system. If the set date is overdue, the record files will be deleted automatically. To setup all channels with the same parameters mark“all”and then click "apply". Reset default setting; click the“default” button and then“apply” button to save the setting.Pressthe “exit” button to exit current interface. Fig 4-13 record configuration-time 4.3.4 Stamp Stamp: Change the position of the camera name or the time stamp.
Digital Video Recorder User Manual Before repositioningafter repositioning 4.3.5 Recycle record System configuration=>record configuration=>recycle record; mark"recycle record" to enable recycle recording. When the disk is full the new files will overwrite the earliest files and keep recoding after the HDD is full; if You disable this function the DVR will stop recording when the HDD is full. Reset default setting; click the“default” button and then“apply” button to save the setting.
Digital Video Recorder User Manual Fig 4-15 schedule configuration-schedule Step2: select channel and double-click to pop up a window as Fig 4-16. Now you can edit week schedule: • Fig 4-16 schedule-week schedule Press the “add” button to add a certain day schedule orpress the“delete” button to delete the selected schedule; Copy: You can copy this schedule to other day by pressing "copy" then "ok".
Digital Video Recorder User Manual • Click “OK” button to save the setting; click “Exit” button to exit current interface. If the user wants to apply the schedule setting of certain channel to other or all channels, he needs to select channel and click “Copy” button. 4.4.2 Motion Step1: enter into system configurationschedule configurationmotion; refer to Fig 4-17: Step2: the setup steps of motion are Similarto theschedule;Refer to 4.4.1 Schedule for details.
Digital Video Recorder User Manual 4.5 Alarm configuration Alarm configuration includes five sub menus: sensor, motion, video loss, other alarm and alarm out. 4.5.1 Sensor Sensor includes three sub menus: basic, alarm handling and schedule. • Basic system configuration =>alarm configuration =>sensor =>basic;Refer to Fig 4-19: Enable sensor alarm and then set the alarm type according to triggered alarm type. Two option: NO and NC (Normally open/closed).
Digital Video Recorder User Manual Fig 4-20 alarm handling-triggerFig configuration-sensor-alarm handling 4-21 alarm Full screen alarm: when alarm is triggered, there will pop up full screen alarm; Email: Select this function. When an alarm is triggered, a notificationemail will be sent to thedesignatedemail box including trigger events, time, snap pictures, device name, ID camera name etc. Snap (for NE or HD series): Select channels.
Digital Video Recorder User Manual • Schedule System configuration =>alarm configuration =>sensor =>schedule;Refer to Fig 4-22: The setup steps of sensor schedule are similar with allschedules;Refer to 4.4.1 Schedule for details. Note: the default schedule of sensor is to bealways on: the color of schedule setting interface is blue. Fig 4-22 sensor-schedule 4.5.2 Motion Motion includes two sub menus: motion and schedule.
Digital Video Recorder User Manual Next: click Area button, a dialog box will pop-up as Fig 4-24 a and 4-24b. To set the sensitivity value (1-8)drag the slide bar in the Area interface, the default value is 6. The higher the value the higher the sensitivity to movement, meaning more events will be recorded.
Digital Video Recorder User Manual To setup all channels with the same parameters choose“all”then apply to save relevant setup to all channels. Reset default setting; click the“default” button and then“apply” button to save the setting.Pressthe “exit” button to exit current interface. • Schedule system configuration =>alarm configuration =>schedule; refer to Fig 4-25:the setup steps of alarm schedule are similar to those in 4.4.1 Fig4-25 alarm configuration-schedule 4.5.
Digital Video Recorder User Manual 4.5.4 Other alarm Select system configurationother alarm (as shown in Fig 4-27) Disk full:You can choose the capacity of the disk storage and select the related alarm. If the disk is full, the system will perform according to the setup. IP conflict: if there is an IP address conflict within the same network, the system will perform according to the setup. Disconnect: if the system recognizesa network disconnectionthe system will perform according to the setup.
Digital Video Recorder User Manual 4.5.5 Alarm out Alarm out includes three sub menus: alarm out,schedule and buzzer • Alarm out System configuration =>alarm out; refer to Fig 4-28: You can set relay alarm out name and select hold time (the interval time between the two adjacent alarms). To setup all channels with the same parameters choose“all”then apply to save relevant setup to all channels. Reset default setting; click the“default” button and then“apply” button to save the setting.
Digital Video Recorder User Manual 4.6 Network configuration Network configuration includes four submenus: network, sub stream, Email and other settings. 4.6.1 Network Step 1: Main menu =>system configuration =>network configuration =>network; refer to Fig4-29: The defaultHTTP port is 80. If the value has changed, you need to add the port number after the IP address; if the HTTP port is set to 82, and the IP address is192.168.0.25the full address is: http://192.168.0.
Digital Video Recorder User Manual 4.6.2 Sub stream System configuration =>network configuration =>sub stream; refer to Fig 4-30:select fps, resolution, quality, encode and max bit rate To setup all channels with the same parameters choose“all”then apply to save relevant setup to all channels. Reset default setting; click the“default” button and then“apply” button to save the setting.Pressthe “exit” button to exit current interface.
Digital Video Recorder User Manual 4.6.3 Email system configuration =>network configuration =>email; refer to Fig 4-31 SMTP Server/Port: the name and port number of SMTP server. After selecting “This server requires a secure connection (SSL)”, you can setup mail servers (such as Gmail/Yahoo/Hotmail) according to the e-mail providerrequirements Note: Gmail SMTP server is "smtp.gmail.com", theport is 465 and the SSL Checkbox is marked [v]. Send address and password: sender’s accountdetails.
Digital Video Recorder User Manual Note: The domain name server selected makes it possible to usea domain name forthe DVR instead of using the DVR's "external" IP address. First register for a user name and password (at the DDNS website), and then apply for a domain name. After completing the registration (and only if the correct port forwarding rules are in effect) you will be able to access yourDVR from the internet. Simply write your domain name in the internet browser's address bar.
Digital Video Recorder User Manual If “Show icons for networked UPnP devices” can’t display in the“Network Tasks” list box, please follow the below operation: Click “Tools”- “Folder options” (figure 4-33) Select the “Show common tasks in folders” in the “Tasks” check box to display the UPnP icon (figure 4-34) Figure 34 Figure 33 (a) To register a domain with Provision-ISR DDNS server follow these steps: 1) Visit our website: http://provision-isr-dns.
Digital Video Recorder User Manual 2) Fill in the registration form, then click "Submit" (figure 4-36) 3) Fill in the host name you want to apply for. Now press "Request Domain",for example "home"(figure 4-37) Figure 37 Figure 36 If there is no problem with the domain registration you will see the following message: “Your domain was successfully created.
Digital Video Recorder User Manual User management configuration Step 1: enter into system configuration =>user management configuration; refer to Fig 4-38: Step 2: click Add button to display a dialog box as Fig 4-39: Fig 4-38 user-management Fig 4-39 add-general ① General: Input user name, password; select user type: normal and advance, input the MAC address of the PC; click OK button. Then this user will be added into the user list box; click Exit button to exit the current interface.
Digital Video Recorder User Manual 4.7 P.T.Z configuration P.T.Z configuration includes two submenus: serial port and advance①Serial port Fig 4-41 P.T.Z configuration-serial port System configuration => P.T.Z configuration =>serial port; Refer to Fig 4-41:mark"Enable" and then setup the value of that camera (address, baud rate and protocol according to the settings of the speed dome). To setup all channels with the same parameters choose“all”then apply to save relevant setup to all channels.
Digital Video Recorder User Manual SAMSUNG, RM110, HY, N-control. ③ Advance Configuration => P.T.Z configuration =>advance;Refer to Fig 4-42: click preset “Setting” button to see a dialog box as Fig 4-43: Fig 4-42 P.T.Z configuration-advance Fig 4-43 advance-preset setting a.
Digital Video Recorder User Manual Fig 4-44 preset set-setting b.user can control the dome rotates up, up left, down, right down, left , left down, right and up right and stop rotating; adjust the rotate speed and the value of zoom, focus and iris of the dome; c. select the serial number of the preset point. If relevant click enable the PTZ light. button to enable the PTZ wiper and click button to Note: PTZ must support wiper and light for these two functions to work.
Digital Video Recorder User Manual adjust the position of the preset point. Click Preview button to preview the cruise line; click OK button to save the setting; click Exit button to exit current interface without saving. c. select a preset point in the cruise line list box. Click "Delete" button to delete that cruise line; click Clear all button to clear all cruise line from the list box; click OK button to save the setting; click Exit button to exit current interface.
Digital Video Recorder User Manual 4.8.1 Reset Reset all settings the device will reboot, please note: perform the reset only after consulting with a technician. 4.8.2 Import/Export User can export the data files into mobile storage devices as backup function, and then import specified data files from mobile storage device to DVR. 4.8.3 Block/Allow list Fig 4-48 Block/Allow list Theauthorized user can block/allowusers from accessing the DVR according to their IP address.
Digital Video Recorder User Manual 5 Record search & playback and backup Search configuration includes four submenus: time search, event search, file management and image. 5.1 Time search Search configuration =>time search; Refer to Fig 5-1: Fig 5-1 Search configuration-time search select channel/s, screen display mode, (highlighted date in the calendar means there are recording on that date) .
Digital Video Recorder User Manual Note: the vertical column representsthe time (hours), while the horizontal column representsthe channels. Another option is to click Play button to playback record on the main screen to start play of last 30 minutes. Note: when the monitor resolution is VGA800*600, the time search interface will appear a hide button, click this button, the whole interface can be expanded.
Digital Video Recorder User Manual Fig 5-2 Search configuration-event search Click on the "Search" button to display the event information in the event list box. Here you can select the date and channel. You can choose events by motion, sensor or All accordingly. Double clicking on a certain record file will start playback. Note: when the monitor resolution is VGA800*600, the event search button will appear as a small line. Place the mouse on the line then click this button to expand the whole interface.
Digital Video Recorder User Manual Unlock: select a locked file and click the "Lock" button to unlock this file. Delete: select an unlocked file and click Delete button to delete this file. After selecting the “All”button user can lock, unlock or delete all files in the file management column. Double clicking an unlocked item willplayback the event. 5.4 Image This option is used to set start, end time and channels to search the captured images and save, lock or delete these images.
Digital Video Recorder User Manual 6 Manage DVR 6.1 Check system information Displaysthe system information.This includes five submenus: system, event, log, network and online user. 6.1.1 System information In this interface, user can check the hardware version, MCU version, kernel version, device ID, etc. 6.1.2 Event information This option is used to check data about recorded events according to the set date. Note: if there are overlapping files, a “+” character will show behind the channel ID. 6.1.
Digital Video Recorder User Manual 6.2 Manual alarm This option is used toactivate the alarm manually, this option also activates the buzzer. 6.3 Disk management 1. Format the disk Go to"disk management" Note: please format the hard disk before startinga recording. If the disk is not formatted, it will show the status of the disk-free space, and total space show OM at the bottom of screenbut the DVR will not record. Clicking the"Refresh" button will refresh the disk information in the list.
Digital Video Recorder User Manual 7 Remote Surveillance 7.1 IE Remote Surveillance To view the DVR from a network it must be connected to a modem or router through the LAN/WAN.The network setup should be done accordingly. Please refer to4.6 Network Setup.This DVR supports IE browser, Firefox and Chrome on Windows XP and Vista platform. 7.1.1 On LAN Step 1: Enter into the DVR’s Main MenuSetupNetwork interface to input IP address, Subnet Mask, etc.
Digital Video Recorder User Manual Step 6: IE will download ActiveX automatically. Then a window pops up and asks for user name and password.Input user name and password correctly, and enter to view. Note: If you cannot download and install ActiveX, please refer to Q&A. 2. Connect the DVR to internet directly. Step 1: Enter into the DVR’s Main MenuSetupNetwork interface to enable PPPoE and then input user name and password received from your ISP. Next, click ‘Apply’.
Digital Video Recorder User Manual 7.2 Remote Surveillance through Macintosh with Safari: Note: the current plug-in version supports only the 32-bit mode, so the safari browser must work on 32-bit mode. This works for Lion OS, with Safari 5.1, though upgrading your computer may cause failure to use Safari. The Setting steps are as follows: First: Right click safari icon and select “Show in Finder”. Second: Select ApplicationsRight click “Safari. App”Select “Get Info”.
Digital Video Recorder User Manual 7.2.1 On LAN Step 1: After starting Apple computer, click icon. The following window will pop up.
Digital Video Recorder User Manual Step 2: Enter into Network interface and then click “Ethernet Connected” to check the internet connection of Apple PC. Step 3: After acquiring the IP address, Subnet Mask and so on, please enter into the DVR’s Main MenuSetupNetwork interface to manually input IP address, Subnet Mask and Gateway according to the configuration of PC. The network segment should be the same as the PC. If using DHCP, please enable DHCP in the DVR and router.
Digital Video Recorder User Manual Step 5: Click icon and then select the Active X control, the welcome interface will be shown. Click “Continue””Install” button，the following window will pop up： Input the name and password of Apple PC and then click “OK” to install this Active X control. Step 6: After finishing installing the Active X control, please quit from the Safari browser. Right click icon on the desktop and then select “Quit” button to quit the browser. Then restart Safari browser.
Digital Video Recorder User Manual 7.
Digital Video Recorder User Manual Note: click button to record manual and the record file will be saved in user’s PC. Screen display mode: Click the icon beside the screen display mode, channel select dialog will appear as below: Take 8-channel DVR for example: user can mark channels form 1-ch to 16-ch at random to display the live pictures, 8 channels can be selected at most. Then click OK button to confirm the setting.
Digital Video Recorder User Manual Please connect speed dome to the device via RS485 firstly, make sure the protocol of the speed dome is supported by the device and set the relative parameters manually. User can control the dome up, down, right, left or stop rotating on ControlCenter, adjust rotation speed, Iris and zoom, focus on the dome, and set the presets, etc. Buttons definition: Buttons Description means the dome rotate up. means the dome rotate up left.
Digital Video Recorder User Manual Click the right mouse on the live interface, a pull-down menu will appear as below Stream: this DVR supports master stream and sub stream. Master stream has higher frame rate, max 25FPS（PAL）/30 FPS（NTSC）for every channel, but it needs higher network bandwidth simultaneously; second stream has low frame rate, max 6FPS （PAL）/7FPS（NTSC） for every channel, it requires low network bandwidth. Therefore, users can select the stream according to their bandwidth.
Digital Video Recorder User Manual Fig 7-5 Play record file interface 81
Digital Video Recorder User Manual This DVR supports remote time search, event search and file management.
Digital Video Recorder User Manual Step2: click “Search” button. The record data will be displayed in the data information list box; the highlight date in the area② means have record data, click those data; select the record channels in area③ Step3: User can set the data playing time and display mode in the area① as required Step4: Select certain item from the data information list box.
Digital Video Recorder User Manual By Event Search: Step1: Enter into Searchevent search; refer to Fig 7-8: Fig 7-8 event search interface Step2: click the highlight date and select record channels and then mark the event type: motion and sensor.
Digital Video Recorder User Manual File Management Step1: Enter into Searchfile management; refer to Fig 7-9: Fig 7-9 file management interface Lock: select certain file item in the file list box and then click “Lock” button to lock this file that ca not be deleted or overlaid Unlock: select a locked file and then click “unlock” button to unlock this file Delete: select an unlock file and then click “delete” button to delete this file from file list 85
Digital Video Recorder User Manual 7.4.2 Remote backup Click Backup button to enter into backup interface, refers to Fig 7-10: Fig 7-10 remote backup interface Step1: select channels, set the start and end time and then click “search’ button to display the file information in the file list box Step2: select backup files and click “browse” button to set the save path. Then click “backup” button to start backup. The backup files will be saved on user’s PC.
Digital Video Recorder User Manual 7.5 Remote System configuration User can remote setup the parameters of the device. Functions of remote configurations include: basic configuration, live configuration, record configuration,scheduleconfiguration,alarm configuration, network configuration, PTZ configuration and user configuration. User should firstly select an item in the menu list on the left, and then setup the relative parameters.
Digital Video Recorder User Manual 7.6 Remote Management Remote Information Search The system will automatically record the working condition and operation process during the period of work. User can view information, such as username, IP address and so on. Enter into INFO→Log. User can set the start time to view the log record as follows: Fig 7-12 Remote information search Note: There may be subtle differences with respect to functions of remote surveillancefrom different sources.
Digital Video Recorder User Manual 8 Mobile Surveillance This DVR supports mobile surveillance by IPhone, Android, blackberry or smart phones with Windows mobile and Symbian OS, though the service may depend on the cellular service provider and3G network availability and function. Dopod D600 (WM5) and Dopod S1 (WM6) was tested and work fine with the DVR. To enable mobile surveillance, first enable network service on the DVR and router, please refer to Chapter 4.6 Network configuration.
Digital Video Recorder User Manual 8.2 SuperLivePro 1.0 Manual (for iOS) Login interface Input server’s IP address (or domain name), user name and password Click “Remember server” to save the setting; click button user can quick input saved server address, user name and password.; If failed connecting, please check below points; 1.) Check the network connection to your iPad/iPhone. 2.) Check if the server address input is invalid. 3.
Digital Video Recorder User Manual Main screen Color adjustment Enlarge picture PTZ 2-way audio PTZ Presets 91
Digital Video Recorder User Manual NavBarIcon meaning: Quick Launch Bar Instruction: Gestures instruction： 1.) Tap to select the current channel, double tap the live image to switch to single channel or multi-channel displaying. 2.) Press for 2+ seconds and drag to swap the position of a Fig. 8.1.5 live channel. 3.) Tap to go back to normal mode when in full screen Snapshots interface You can see the captured images in the Image interface (Fig. 8.1.7), tap the thumbnail to check the full image. Fig. 8.1.
Digital Video Recorder User Manual Using the playback interface you can playback files on the DVR, follow the next steps just like on the web or local interface: Search menu Time search Remote file search Event search Local file search 93
Digital Video Recorder User Manual Configuration and information interface to change DVR settings: Settings menu Basic menu Record menu Network menu PTZ menu System menu Network menu Online users Email menu 94
Digital Video Recorder User Manual Device list interface for quick login (figure 8.1.8-8.1.9): Fig. 8.1.8 Fig. 8.1.
Digital Video Recorder User Manual 8.4 Windows Mobile application Step1：Firstly activate the network access on mobile phone and then run “Internet Explorer”. Input the server’s address and the connection is built up shown as below picture in the left: Step2：Click on the software name. A dialog box pops up as below picture in the middle: Step3：Click “Yes” to start downloading and installing: Step4：PCam will be opened automatically after installed.
Digital Video Recorder User Manual Notice: User name and password here are the same with that used on the DVR. The default is admin and 123456. 8.5 Symbian OS application Please use the smart phones with symbian version supported by this unit. The detail information is as follows: Symbian S40 support Symbian UIQ support Symbian S80 support Symbian S60 support rd Symbian S60 3 Edition-Symbian OS v9.1 support rd Symbian S60 3 Edition with FP 1-Symbian OS v9.
Digital Video Recorder User Manual Step3：A welcome window will pop up and requires a package. Click the software name to download. Refer picture in the right: Step4：A security windows will pop up after downloading and ask if install the package. Click YES to install. Step5：A Scam shortcut icon appears on the system menu after finished. Step6：Run Scam program.It will enter a function interface. Refer picture in the left: Step7：Click System setting--->Login Setting to enter login interface.
Digital Video Recorder User Manual Notice: User name and password here are the same with that used on the DVR. The default is admin and 123456. Step10：In Live View, users can do snapshot, change channels and control PTZ. Refer picture in the right: 8.6 BlackBerry OS application installation guide 8.6.1 Installation instruction for BlackBerry Mobile phone Client 1. Open the browser of BlackBerry phone and enter sever address 2. Click “SuperCam” to link 3.
Digital Video Recorder User Manual 4. Finished downloading, the software will be installed automatically. Note: If the software fails to download, please check in accordance with the following steps: 1. Check whether the network of mobile phone is normal or not 2. Check whether DVR server connect network normally or not 3. Modify the option of Browser Configuration. (1) Enter into Menu->Option->Browser Configuration; configure referring to the following figure in the left.
Digital Video Recorder User Manual Note：When user used the SuperCam software in mobile phone with touch screen, there will be compatible problem. Solution:Enter into Options Menu->Advance options->Applications->SuperCam and click “Disable Compatibility” button. This problem will be solved. 8.6.2 BlackBerry OS application guide 1. Login Enter server’s IP address (or domain name), user’s ID and password.
Digital Video Recorder User Manual 2. Main interface Playback Log Information Logoff Live 3.
Digital Video Recorder User Manual Note: User can click Mark 1 Return button on the Blackberry phone to return the previous interface.
Digital Video Recorder User Manual 4. Server list 5. Software configuration 6.
Digital Video Recorder User Manual Appendix A Q&A Q1. Why can't the DVR start after connecting to the power? a. The adapter has been damaged or is malfunctioned, change power adapter. b. The HDD might be malfunctioning Please remove the HDD to check. Q2. The menu is missing from the live image display a. Right click on the attached mouse or click the "menu" button on the DVR or remote. b. Press the ESC button for 5 seconds until you hear a beep. Q3.
Digital Video Recorder User Manual Q6. Cannot record a. HDD not formatted. Format it manually to FAT32 first. b. The record function is disabled or the setup is not correct. Please refer toChapter 5 Record, search, playback and backup. c. HDD is full and the recycle function is turned off. Please refer to 4.3 Record configurations. Changethe HDD or enable recycle. d. The HDD is damaged. Change to a new one. Q7. The mouse is not working. a. wait 1-2 minutes after the mouse is connected.
Digital Video Recorder User Manual ②select Security------Custom Level….Refer to Fig 8-1 ③Enable all the sub options under “ActiveX controls and plug-ins” refer to Fig 8-2 ④ Then click ok to finish setup. b. Other plug-ins or anti-virus block activeX. Please uninstall or close them.
Digital Video Recorder User Manual Q9: when DVR starts, it displays “please wait…”all the time First option: hard-disk data cable is causing the problem. Solution: shut down and unplug the DVR from the power, check the cables connected to the hard-disk are connected. If this does not solve the problem try using different cables. The second possible reason: DVR is forced to stop because hard disk has disabled track which causes the system checking hard while the disk cannot skip.
Digital Video Recorder User Manual Q12: Whatare the minimum configurations of PC for clients connecting? PC Module CPU Motherboard HDD RAM VGA OS DirectX Parameters Intel Celeron 2.4G Intel 845 80G 512M NVIDIA GeForce MX440/FX5200 ATIRADEON 7500/X300 Windows 2000(SP4 above) /Windows XP(SP2 above) /VISTA 9.
Digital Video Recorder User Manual a. Enter Control PanelUser Account and Family Safety User Account Control(refer to below picture); click Turn User Account on or off. Cancel Use User Account Control (UAC) to help protect your computer. b. Right click IE browser (refer to Fig 14-2), select Run as administrator to run browser.
Digital Video Recorder User Manual Appendix BCalculate Recording Capacity Users can calculate the size of hard disk according to the saving time and DVR recording settings. The DVR uses fixed video bit rate. The below are the details at different settings.
Digital Video Recorder User Manual Appendix C Compatible Devices 1. Verified &compatible USB drives(Format only to FAT32) Brand Capacity SSK 512MB, 1G, 2GB Netac 4GB Kingston 2GB, 4GB Aigo 2GB Smatter vider 1GB SanDisk 4GB 2.
Digital Video Recorder User Manual 3. Verified & compatible HDD list Brand Capacity WD AV-GP 20EURS-73S48Y0 2.0T WD AV-GP 10EURS-630AB1 1.0T WD 1002FAEX-00Z3A0 1.0T WD AV-GP 5000AVDS-63U7B1 500G WD 5000AADS-00L4B1 500G WD AV-GP 3200AVVS-63L2B0 320G WD 320G 3200AAJS Seagate Barracuda LP Seagate Barracuda LP ST2000DL003 ST3200542AS 2.0T 2TB Seagate Barracuda 7200.11 ST31500341AS 1.5T Seagate SV35.3 ST31000340SV 1T Seagate Pipeline HD.2 ST3500312CS 500G Seagate Barracuda 7200.
Digital Video Recorder User Manual Appendix D Form at Num ber of Inputs Playback Channels Rem ote Playback Channels Live Preview While Playback Loop Im age Capture Output Type Dual Display Case Audio Input(Output) Tw o Way Audio Mic In Alarm In(out) PTZ Control Recording CIF Recording Channels CIF Recording D1 Recording Channels D1 Recording 1080P Recording Channels 1080P H.
Digital Video Recorder User Manual Appendix E 8CH DVRSpecifications SA-8200N+ SA-8200HD+ (1U) SA-8200D1SDI Form at D1 + CIF D1 HD-SDI + D1 Num be r of Inputs 4 D1 + 4 CIF 8 4 SDI + 4 D1 Playback Channe ls 8 8 4 Re m ote Playback Channe ls 4 4 1 Live Pre vie w While Playback No Yes No Loop No No 4 Im age Capture Yes Yes Yes Output Type CVBS, VGA, HDMI, Spot CVBS, VGA, HDMI, Spot CVBS, VGA, HDMI, Spot Dual Dis play Yes Yes Yes Cas e Small 1U 1U 2U Audio Input 4 4 4 Audio Output 1 1 1 Tw o Way Audio Yes Yes
Digital Video Recorder User Manual Appendix F Form at Num ber of Inputs Local Playback Channels Rem ote Playback Channels Live Preview While Playback Loop Im age Capture Output Type Dual Display Case Audio Input (Output) Tw o Way Audio Mic In Alarm In Alarm Out PTZ Control Recording CIF Recording Channels CIF Recording D1 Recording Channels D1 Recording 1080P Recording Channels 1080P H.
Digital Video Recorder User Manual Appendix G 24CH/32CH DVRSpecifications Form at Num ber of Inputs Local Playback Channels Rem ote Playback Channels Live Preview While Playback Loop Im age Capture Output Type Dual Display Case Audio Input Audio Output Tw o Way Audio Mic In Alarm In Alarm Out PTZ Control Recording CIF Recording Channels CIF Recording D1 Recording Channels D1 Recording 1080P H.
