Owner Manual

8.6” (218 mm) 8.6” (218 mm)
SPL & SAL
User’s Manual
/ Mounting Template
Up to 120 lbs / 54 kg
Included Mounting Hardware
1. Mount (SPL or SAL) (x1)
2. M5 x 10, 15 & 25 mm bolts (x4)
3. M6 x 10, 15 & 25 mm bolts (x4)
4. M8 x 10, 15 & 25 mm bolts (x4)
5. Rectangular washers (x4)
6. Concrete anchors (x4)
7. Round washers (x4)
8. 5/16” lag bolts (x4)
9. Mounting template (x1)
10. Allen key (x2)
11. Wrench (x1)
You Will Need
A. Bubble level
C. Marker
D. Drill
E. 3/16” (wood) or
1/2” (concrete) drill bit
F. Hammer
G. Wrench
*SPL used in diagrams, steps also apply to SAL.
(2) where you want
to mount your TV.
2.2a Mark the center of the studs. Using the
provided mounting template** mark the
4 holes where the wall plate will be
mounted. Make sure it’s leveled.
2.3a Drill a 3/16” hole on each mark.
2.4a Mount the wall plate using the lag bolts and the round washers.
Do not overtighten.
2a. Drywall Installation1. Adjust Wall Plate Location
2b. Concrete Installation
3a. Fix hBars to TV 3b.Fix hBars to TV(For Curved LCD/LED TV and SAMSUNG TV)
400 only and 300 high
300 medium
300 low and 200 high
200 low
**SPL & SAL
mounting template
You can use masking tape
(one that won’t damage your
wall) to keep it in place.
Make sure it is leveled.
4. Hang TV from Arm
SAL
SPL
*Important Note
Due to SPL’s nature, the center of your TV will only be on the center of
the wall plate when the mount is fully extended; otherwise it will be
2.1b Using the provided mounting
template** mark the 4 holes where
the wall plate will be mounted.
Have a separation of no more than
17” (430 mm) between right and
left holes.
2.2b Drill a 1/2” hole with the same
depth of the anchor on each mark.
2.3b Insert a concrete anchor in each hole until it’s
2.4b Mount the wall plate using the lag bolts and round washers.
Do not overtighten.
4.1 Hang hBars from appropriate
keyholes on center bar depending on
hBars spacing and desired height.
See chart.
We recomend one person holds the TV while
other makes sure bolts are in place.
Rectangular
washer
3a.1 Center top hBar horizontally
and bolt to matching holes on
the back of your TV using M5,
M6 or M8 bolts (x4) and
optional rectangular washers
(x4).
Do not overtighten.
3a.2 Center bottom hBar
horizontally and bolt to
matching holes on the back of
your TV using M5, M6 or M8
bolts (x4) and optional
rectangular washers (x4).
Do not overtighten.
4.2 Fix lower hBar with allen bolts (x2).
4.3 Tighten upper and lower bolts.
Do not over tighten.
Bolts go
on top
1.1 Loosen bolts and position the wall plate in the
desired sliding slots of wall plate rails. You may
have to remove the bolts (x4) and washers (x4).
Once you have bolted the rails to the wall, it will
*Make sure you understand the important
note.
Upper hBar
Lower hBar
3b.1 Center top hBar horizontally
and bolt to matching holes on
the back of your TV using M8
bolts (x4) and spacer (x8)
optional rectangular washers
(x4).
Do not overtighten.
3b.2 Center bottom hBar
horizontally and bolt to
matching holes on the back of
your TV using M8 bolts (x4)
and spacer (x8) and optional
rectangular washers (x4).
Do not overtighten.
Bolts go
on top
Upper hBar
Lower hBar
5. Conceal Cables Horizontal Adjustment
Adjust the level of the TV by
loosening and re-tightening
the upper and lower nuts with
an hex wrench.
4.1 Run cables along arm channels.
Do not run power and signal
cables together, this may
cause interference.
4.2 Push cable covers until you hear
them click in place.
Panning
extended at 90˚
Adjust arms by tightening or loosening bolts on
articulations. Don’t remove bolts from arms, TV may
fall down and somebody may get hurt.
-90˚ to 0˚ to 90˚
Tilting
Gently pull the top of your TV while
pushing the bottom to the desired
position up to 15˚. Do the opposite to
tilt up.
Adjust tilt by tightening or loosening
these bolts, on both sides.
-3 to 15˚
Included Mounting Hardware
(For Curved LCD/LED TV and SAMSUNG TV)
1. M8 x 30 bolts (x4)
2. M8x 50 bolts (x4)
3. Φ15 x Φ8xΦ5 mm spacer (x8)
4. Φ15 x Φ8xΦ15 mm spacer (x8)
Rectangular
washer
Disclaimer
Promounts intends to make this manual accurate and complete, however, Promounts makes no claim that the information contained
herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation
or use of this product. The information contained in this document is subject to change without notice or obligation of any kind.
Promounts makes no representation of warranty, expressed or implied, regarding the information contained herein. Promounts
ciency of the information contained in this document.
Warnings & Cautions
IT IS HIGHLY RECOMMENDED THAT THIS PRODUCT BE INSTALLED BY A PROFESSIONAL.
PLEASE REVIEW THIS INSTRUCTION MANUAL COMPLETELY BEFORE STARTING THE INSTALLATION PROCESS.
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding
instruction.
WARNING: Improper installation can result in serious personal injury! Make sure that the structural members can support a weight
factor
WARNING: Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted.
WARNING: The installer is responsible for verifying that the wall or ceiling to which the mount is anchored will safely support the
combined load of all attached components or other equipment.
WARNING: The weight of the display placed on the mount must not exceed the maximum load capacity of the mounts.
WARNING: Watch for pinch points. Do not put your
WARNING: Make sure the mount and brackets are correctly oriented.
CAUTION: Check the unit for shipping damage before you begin the installation.
For more information, visit:
www.promounts.com
Promounts
TM
name, logo and model numbers are property of Promounts.
© Promounts
®
AUM022 v2.0
BY
Center
Bars
Upper
hBars
Lower
hBars
Arms
Wall
plates
Wall
plate
rails