Manual

ManualsBrandsProkit's Industries ManualsPower ToolsSS-952B

SS-952B

SMD Rework Station with Vacuum Pickup

User’s Manual

Edition

2013

Summary of content (16 pages)

PAGE 2
SS-952B Instruction Manual Thanks for buying PRO’SKIT SS-952B SMD Rework Station with vacuum pickup. Please read the user’s manual carefully before using the product. Specification Power supply Power Air pump Capability Temperature 210V~240V/50Hz 600W(MAX) Diaphragm special-purpose lathe pump 23L / min (MAX) 100℃-480℃ Features  Closed-loop temperature control. Digital display for easy adjustment. High power, quick warm up.  ESD safe design, prevent static and electric leakage damage the PCB.
PAGE 3
1.
PAGE 4
2. Display function description From left to right, that first digital indication: A. Stand for auto real-time measuring; b. Stand for the set temperature; The second, third and forth digital indicate the temperature degree, the six and seventh digital indicate the airflow in percentage; 3. Operating Instructions When connected power plug, the device starts to work, temperature display indicate ”A100” and air flow display indicate “F15”. After adjust temperature and air then begin to use.
PAGE 5
3-3 Set Airflow  Press “C3” button, airflow indication change from “F15” to “F18”, and airflow starts to increase; release the button when it reaches “F99”, the glass ball that in the airflow meter will rising to the top, indicating the max airflow.  Press “C4” button, airflow indication change from“F99”to “F96”, airflow starts to decrease; release the button when it reaches “F06”, the minimum for no airflow.
PAGE 6
device will automatically blow air (at room temperature) to bring down temperature to 90℃ The panel will then display the following after reaching the safe temperature level and to indicate that the device is now in sleep mode. NOTES:  Time is configurable from 1 to 20 minutes (default 5 minutes).  The device has a switch located at the handle (cradle), which activates the countdown before the system goes to sleep.
PAGE 7
Prepare work before operation  Select the FP Pick-up Wire, The size of it and IC should match. FP Pick-up has a small wire (15mm). But it probably needs a big FP Pick-up wire (20mm) Please choose the suitable FP Pick-up Wire according to the size of IC Select the suitable nozzle, which should be matched with IC in size.  Loosen the screw of nozzle  Set up the nozzle according to the graph.  Tighten the screw properly 8 The process of removing solder.
PAGE 8
 Joining evenly blow the hot air to leads.  Cleaning After jointing is finished, clean the remaining solder NOTE: its effect to joint by hot air, but it is also possible lead to the problem of solder link or solder ball, we advice you to check it carefully. NOTE:  Don’t overexert while fixing muzzle, or pull the muzzle with forceps, or screw breech block too tightly.  Be careful, working with high temperature. Don’t use this product near flammable gas, paper, or other flammable things.
PAGE 9
NOTE:  Pay attention that tube can not be bent, it may influence of gas flow  Absorbed item surface should be smooth, in order to be sucked.  Pay attention to prevention of ESD, so as not to damage the device 11. Change the fuse  Make sure the equipment is completely isolated from the main power source before changing the fuse.  The fuse of the main unit is located at the back of the equipment, right above the power plug connector.  Change the blown fuse by unscrewing the fuse holder.
PAGE 10
SS-952B 二合一熱拆吸筆焊台感謝您使用寶工 SS-952B 二合一熱拆吸筆焊台。為了您更好的使用本機，請您在使用產品前詳細閱讀本使用手冊，以發揮本機的最佳效能。閱讀後請妥為收存，以備日後查閱。 1. 產品概述 1-1 規格電源電壓功率消耗空氣泵容量熱空氣溫度 210V ~240V / 50Hz 600W（最大）膜片式專用泵 23L/min (最高) 100℃- 480℃ 1-2 功能 ◆ 感測器閉合回路,數顯控溫,調溫方便,開機功率大,升溫迅速,溫度精確穩定,不受出風量影響. ◆ 防靜電設計,防止因靜電及漏電而損壞 PCB 板. ◆ 不需接觸焊點的焊錫方式,可免除零件位移及熱充擊.
PAGE 11
2.
PAGE 12
2-1 顯示器功能狀態說明從左至右，第一位指示功能： A-表示自動即時測量 b-表示設置溫度第二、三、四位元顯示溫度值第六、七位元顯示氣量的百分數當七個顯示器全顯示“-＂時，表示機處於休眠狀態。 3. 操作使用方法插上電源，整機開始工作，溫度顯示為“A100＂風量顯示為“F51＂。設置需要的溫度及風量, 便可以開始使用.
PAGE 13
 ① ② 3-3. 風量設定按住右邊第四個按鈕 C3，風量顯示從“F 15＂轉為“F18＂風量即開始上升，直至顯示為“F 99＂鬆開按鈕，風量計玻珠升到頂端，此時風量達到最高。按住右邊第五個按鈕 C4,風量顯示從“F99＂轉為“F 96＂風量即開始下降,直至降到“F 06＂此時風量最低，鬆開按鈕，風量就會停止。 4. 復位鍵的使用按住中間第三個按鈕 D，整機馬上恢復到待機狀態，溫度顯示為 “A100＂和“F51＂。注意: 當本機處於高溫時，不要直接使用復位鍵，應先將溫度降至最低再按復位鍵,以免造成對發熱體及手柄的損壞。 5. 手柄開關的使用說明  觸點式開關裝置在手柄架上,當您工作完畢把手柄放回支架時,開關就會接通.  手柄開關接通時,發熱體即進入休眠計時,當您 5 分鐘不提起手柄工作，溫度顯示為“E＂並自動進入息機省電保護狀態; 當您重新提起手柄工作,機器自動恢復到原來的設置狀態.
PAGE 14
替換發熱材料編號 5SS-952B-F-H 名稱/規格發熱材料/(210 伏特-240 伏特)250 瓦特 6-1 替換部件 6-2 替換發熱材料  鬆開拴緊手柄的 3 枚螺絲,移出電線管。  拆開手柄，鬆開接地電線護套，取出管件，管同內裝置有石英玻璃和熱絕緣體。  勿掉落或遺失  取出發熱材料鬆開終端板，取出發熱材料。  插入新發熱材料小心處理，切勿磨擦發熱材料電線，插入新發熱材料，重接終端。感測器線有極性，應注意區別。（發熱芯傳器黃色為正極，紅色為負極。  手柄連接線中感測器的兩根線，紅色為負極，黑色為正極，請確認後，再連接發熱材料）。  依拆開時的相反程式，回裝手柄。 7. ◇ ◇ ◇ ◇ ◇ 使用前準備工作選擇與積體電路尺寸相配合的起拔鋼絲.FP 起拔器配有小鋼絲(15 毫米)但可能需要大起拔鋼絲(20 毫米).請依照集成電路塊尺寸,選擇適合的起拔鋼絲. 選擇積體電路尺寸相配合的噴咀. 鬆開噴咀螺絲. 裝置噴咀. 適當緊固螺絲 8.
PAGE 15
◇ ◇ ◇ ◇ 塗抹適量錫膏,將 SMD 放在電路板上。預熱 SMD。焊接,向引線部份平均噴出熱氣。清理,焊接完畢，清除熔料殘餘。注意：用熱氣焊接是有效的,但也可能導致焊劑球、焊劑搭連等問題。我們建議您仔細檢查焊接元件。注意事項： * 安裝噴咀時勿用力過大，或用鉗子拉動邊緣，勿過度擰緊螺絲。 * 必須在發熱管與噴咀冷卻時安裝噴咀。 * 小心高溫操作切勿在易燃氣體、紙質、或其他易燃物品附近，使用本拆焊台，噴咀十分灸熱，為免灼傷身體，切勿觸摸發熱管，或以熱氣直噴身體部位. 對於新機，因手柄內有隔熱材料—雲母管，開機後短時間內冒白煙，這屬正常現象。 10. 吸筆使用 1) 依據需要提取的物品重量(不大於 100g)及表面大小, 選擇使用的吸盤規格, 安裝在吸筆的頭部. 2) 將吸盤水平放置在被吸物的表面, 用手按住吸筆上的孔位, 使吸筆吸住物品. 3) 將被吸物移動到放置的位置, 松開堵住吸筆上的小孔, 物品會脫離吸盤. 注意事項： * 使用吸筆時注意皮管不可彎折, 影響氣體流動. * 被吸物表面需要光潔, 以利被吸取. * 注意防靜電措施, 以免損壞器件. 11.