ITEM #0040040 BATHROOM FAUCET MODEL #67211-6101 Francias / Español p. 9 ATTACH YOUR RECEIPT HERE Serial Number ____________ Purchase Date ____________ Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-389-8827 , 8 a.m. - 8 p.m., EST, Monday - Friday. AB12330 Lowes.
PACKAGE CONTENTS D A E F J M H B N L G K I C PART A B C D E F G H I J K L M N DESCRIPTION Faucet Mounting Bracket (Preassembled to Faucet (A)) Mounting Nut (Preassembled to Faucet (A)) Stopper (Preassembled to Pop-up Body (H)) Flange (Preassembled to Pop-up Body (H)) Gasket (Preassembled to Pop-up Body (H)) Nut (Preassembled to Pop-up Body (H)) Pop-up Body Pivot Nut (Preassembled to Pop-up Body (H)) Horizontal Rod (Preassembled to Lift Rod Strap (M)) QUANTITY 1 2 2 1 1 1 1 1 1 1 Clip (Preassemb
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate, or install the product. WARNING: Follow the installation instructions carefully. Proper installation is the installer’s responsibility. Failure to follow correct installation procedures can result in the faucet being loose, which can result in serious injury. CAUTION: Check local building codes before beginning installation to ensure compliance.
ASSEMBLY INSTRUCTIONS 2. Place the faucet (A) through the mounting holes on the sink. 2 Note: If the sink surface is uneven, use silicone sealant (not included) to create a watertight seal. A From under the sink, slide the mounting brackets (B) onto the threaded bolts on the faucet (A) and secure with mounting nuts (C). Note: Tighten mounting nuts until snug. Do not overtighten. B C 3. Connect a 1/2 in. IPS faucet connector or coupling nuts (not included) with 3/8 in. O.D.
ASSEMBLY INSTRUCTIONS 5. (E) from the Remove the stopper (D) and the pop-up body (H). Screw the nut (G) all the way down onto the pop-up body (H) and then push the gasket (F) down. 5 D E F G H 6. Apply silicone sealant (not included) to the underside of the (E). 6 E 7. Insert the pop-up body (H) into the sink and screw the (E) onto the pop-up body (H). Ensure the pivot hole is facing the back of the sink. Tighten the nut (G) and remove the pivot nut (I). 7 E G I H Lowes.
ASSEMBLY INSTRUCTIONS 8. Insert the stopper (D) onto the sink. Remove the preassembled horizontal rod (J) and clip (K) from the lift rod strap (M). Install the horizontal rod (J) into the popup body (H) and through the hole of the stopper (D). Install the pivot nut (I) onto the horizontal rod (J) and hand-tighten it back onto the pop-up body (H). 8 I D J H 9. Re-attach the lift rod strap (M) to the horizontal rod (J) using the clip (K). 9 M K J 10.
OPERATING INSTRUCTIONS 1. After the installation is complete: 1 a. Remove the aerator on the faucet (A). b. Turn on the water supply and allow both hot and cold water to run for at least one minute each. A c. While the water is running, check for leaks. d. Replace the aerator. CARE AND MAINTENANCE Clean carefully by gently wiping with a grit-free damp cloth. Use only mild soap with water. Never use acids, harsh chemicals, or abrasive detergents to clean the surface.
WARRANTY This faucet has been manufactured under the highest standard of workmanship. All parts of this faucet are warranted to be free from leaks or drips during domestic use for as long as the original purchaser owns this product. THIS EXCLUDES INDUSTRIAL, COMMERCIAL, OR BUSINESS USE. The manufacturer will replace FREE OF CHARGE, under the warranty conditions the entire unit or any part (at our option) which proves defective in material and/or workmanship under normal installation, use, and service.