Technical Specifications

ManualsBrandsPowernail ManualsAir Nailers & Staplers16-Gauge Pneumatic Hardwood Flooring Cleat Nailer

Read this manual before you use this Nailer.

Follow all safety warnings and instructions. Do not

attempt any disassembly or repairs while the air

line is connected. Always disconnect the air line

ﬁ rst. Do not use excessive unregulated air pressure.

If you are uncertain about the operation of the Nailer,

call us directly a 1-800-323-1653 for assistance

or contact the closest Powernail

Dealer for help.

Please retain this information for future reference.

WARNING

REVISION G3-0908

Operation and Maintenance Manual

Models 445 XLL, XLS, LL, LS, SL, SS, & SN

Pneumatic Powernailer

POWERNAIL

CO.

1300 Rose Road, Lake Zurich, IL 60047

Phone: 1-800-323-1653

Website: http://www.powernail.com

REVISION G.3

Summary of content (12 pages)

PAGE 1
POWERNAIL® CO. 1300 Rose Road, Lake Zurich, IL 60047 Phone: 1-800-323-1653 Website: http://www.powernail.com Operation and Maintenance Manual Models 445 XLL, XLS, LL, LS, SL, SS, & SN Pneumatic Powernailer® REVISION G.3 WARNING Read this manual before you use this Nailer. Follow all safety warnings and instructions. Do not attempt any disassembly or repairs while the air line is connected. Always disconnect the air line first. Do not use excessive unregulated air pressure.
PAGE 2
TO PREVENT ACCIDENTAL INJURIES: Always wear approved front and side EYE PROTECTION when operating this Nailer. Others in the work area should also wear front and side EYE PROTECTION. Eye protection will help guard against flying nails and debris, which could cause severe eye injury. EAR PROTECTION may be required to prevent hearing damage when there are high noise levels in the work area.
PAGE 3
AIR SUPPLY: The air must be clean and dry. Dirty and/or wet air will damage the Nailer. A combination filter-regulatorlubricator is required for proper Nailer performance and should be placed close to the Nailer per manufacturers’ recommendations. TO LOAD MODEL 445 XLL, LL or SL: Place up to two sticks (200 Powercleats) into the Nail Channel feed slot. Pull back the spring loaded Nail Pusher over the nails until it contacts the last nail and slowly release the Nail Pusher.
PAGE 4
TO REPLACE DRIVING BLADE (#14): 4 #10-32 cap screws holding the Plunger (#12) to the 1. Disconnect the air supply. Return Cylinder (#11). 2. Remove the four socket head cap screws holding the Adapter Foot, Foot and Nail Channel Assembly to the body. 5. Pull the Plunger up and out of the Nailer Body (#1) cavity. 3. Remove the Rubber Bumper. 4. Pull the Driving Blade with pliers until the Piston is fully extended outward towards the bottom of the cylinder. 5.
PAGE 5
the Teflon®Seal Ring. DO NOT OVER STRETCH THE 5 Return Cylinder O-Ring Gasket (#26): TEFLON® SEAL RING! Be sure the Teflon® Seal Ring is 1. Place a new O-Ring Gasket in the groove on top of the Return Cylinder when you reassemble the Driving centered all around the seal groove and not twisted. Blade Assembly. 4. Wipe off the Seal surface with a clean rag and lubricate it generously with the supplied lubricant, O-Ring 2.
PAGE 6
TO CLEAR A NAIL JAM (continued): 3. Separate the Foot and gate with a screw driver just enough to clear out the jammed nail. 4. Put thread locking compound on all screws and reassemble the components.
PAGE 7
MODELS 445 XLL, XLS, LL, LS, SL, SS & SN PARTS LIST ITEM # PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 09-445-29701 09-445-29702 09-445-29703 09-445-29703.
PAGE 8
MODELS 445 XLL, XLS, LL, LS, SL, SS & SN PARTS LIST ITEM # 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 PART NO. 09-445-29751 09-445-29754 09-445-29832 09-445-29756 09-445-29757 09-445-29758 09-445-29759 09-445-29760 09-445-29790 09-445-29791 09-445-29792 09-445-29795 09-445-29796 09-445-29797 09-445-29798 09-445-29799 09-445-29822 09-445-29836 09-445-29819 09-445-29738.1 DESCRIPTION QTY.
PAGE 9
POWERNAILER MODELS 445 XLL, XLS, LL, LS, SL, SS
PAGE 10
POWERNAILER MODEL 445 SN
PAGE 11
POWERCLEATS LENGTH DETERMINATION CHART This chart will assist you in determining the proper length of Powercleats® to use for various thicknesses of flooring. Approximate vertical penetration of the Powercleat under the hardwood floor is shown for each application. This is only a guide. Results should be tested in the field before proceeding.
PAGE 12
POWERNAILER MODEL 445 TROUBLE SHOOTING CHART PROBLEM POSSIBLE CAUSE SOLUTION Check air supply for 70 psi minimum to 110 psi maximum 2. Lack of lubrication Manually lubricate through male air inlet fitting Driving blade 3. Excessive dirt inside nailer Disassemble and clean does not retract 4. Bent or burred driving blade Replace driving blade 5. Seals worn out Replace all seals 6. U-Cup Lip Seals installed upside down Replace all seals 1. Low air pressure Turn up air pressure to 70-110 psi max 2.