IMPORTANT MANUAL Do Not Throw Away OPERATOR'S MANUAL MODEL: WARNING: Read this Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. PP175G42 LAWN TRACTOR ALWAYS WEAR EYE PROTECTION DURING OPERATION Visit our website: www.poulanpro.com Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. 115 78 06-49 Rev. 2 05.25.
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. SLOPE OPERATION • • • • WARNING! When loading or unloading this machine, do not exceed the maximum recommended operation angle of 15°. • Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Operation on all slopes requires extreme caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it. • Mow up and down slopes, not across.
PRODUCT SPECIFICATIONS Gasoline Capacity and type: 1.5 Gallons/5,67 L Regular Unleaded Oil Type: (API: SJ-SN) SAE 30 (above 32°F/0°C) SAE 5W30 (below 32°F/0°C) Oil Capacity: W/Filter: 48 Oz./1,4 L W/out Filter: 44 Oz./1,3 L Spark Plug: Champion RC12YC (Gap: .030"/ 0,76 mm) Charging System: Battery: 3 Amps Battery 5 Amps Headlights Amp/Hr: 35 Min. CCA: 280 Case size: U1R Blade Bolt Torque: CONGRATULATIONS on your purchase of a new tractor.
UNASSEMBLED PARTS Steering Wheel (1) Lock Steering Wheel Insert Washer (1) Large Flat Washer Steering Wheel (1) Hex Bolt Steering Steering Wheel Adapter Extension Shaft Steering Boot Seat (1) Washer (1) Knob (1) Seat Keys Oil Drain Extension Slope Sheet Battery (2) Hex Bolts Key(s) (2) Nut Keps 5
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness. TOOLS REQUIRED FOR ASSEMBLY NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps.
ASSEMBLY TO INSTALL STEERING WHEEL (See Fig. 2) INSTALL SEAT (See Fig. 3) ASSEMBLE EXTENSION SHAFT AND BOOT • Slide extension shaft onto lower steering shaft. • Place tabs of steering boot over tab slots in dash and push down to secure. Adjust seat before tightening adjustment knob. • Remove adjustment knob and cup washer securing seat to cardboard packing and set aside. • Remove seat from the cardboard packing and set seat aside. Remove the cardboard packing and discard.
ASSEMBLY ✓CHECKLIST CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on side of tires. BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ENSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT.
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. G H D E B F A C J Fig. 4 Our tractors conform to the applicable safety standards of the American National Standards Institute. (E) ATTACHMENT CLUTCH LEVER - Used to engage the mower blades, or other attachments mounted to your tractor.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses. HOW TO USE YOUR TRACTOR IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY POSITION OTHER THAN "STOP" WILL CAUSE THE BATTERY TO DISCHARGE AND GO DEAD. TO SET PARKING BRAKE (See Fig.
OPERATION TO ADJUST MOWER CUTTING HEIGHT (See Fig. 9) TO OPERATE MOWER Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills. • Select desired height of cut.
OPERATION BEFORE STARTING THE ENGINE REVERSE OPERATION SYSTEM (ROS) (See Fig. 12) CHECK ENGINE OIL LEVEL Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position. The engine in your tractor has been shipped from the factory already filled with summer weight oil. • Check engine oil with tractor on level ground.
OPERATION TO START ENGINE (See Fig. 4) MOWING TIPS When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. • Sit on seat in operating position, depress clutch/brake pedal and set parking brake. • Place gear shift lever in neutral position. • Move attachment clutch to “DISENGAGED” position. • Move throttle control to choke position. NOTE: Before starting, read the warm and cold starting procedures below.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation Check Tire Pressure T R A C T O R Check Operator Presence and ROS Systems Check for Loose Fasteners Check/Replace Mower Blades 3 Lubrication Chart Check Battery Level 4 Clean Battery and Terminals Clean Debris off Steering Plate 5 Check Transaxle Cooling Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (mode
MAINTENANCE TRACTOR BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. Always observe safety rules when per form ing any maintenance. BRAKE OPERATION If tractor requires more than five (5) feet (1,5 m) to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual.
MAINTENANCE V-BELTS OIL DRAIN HOLE Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. OIL DRAIN PLUG OIL DRAIN EXTENSION TRANSAXLE MAINTENANCE Keep transaxle free from build-up of dirt and chaff which can restrict cooling. Do not attempt to clean transaxle while engine is running or while the transaxle is hot.
MAINTENANCE CLEANING ENGINE COOLING SYSTEM (See Fig. 18) Debris may clog the engine's air cooling system. Remove blower housing and clean the area shown to prevent overheating and engine damage. • • CLEAN OUT CHAFF AND DEBRIS AIR SCREEN Clean engine, battery, seat, finish, etc. of all foreign matter. Clean debris from steering plate. Debris can restrict clutch/brake pedal shaft movement, causing belt slip and loss of drive. See Fig. 20. CAUTION: Avoid all pinch points and movable parts.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress clutch/brake pedal fully and set parking brake. • Place gearshift lever in neutral position. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO REMOVE MOWER (See Fig.
SERVICE AND ADJUSTMENTS • • ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring. Repeat on opposite side of tractor. • Insert end of link (E) into hole in front mower bracket and secure with washer and retainer spring (J). E A J F H B • Fig.
SERVICE AND ADJUSTMENTS TO LEVEL MOWER FRONT-TO-BACK ADJUSTMENT (See Figs. 29 & 30) IMPORTANT: Deck must be level side-to-side. Ensure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.
SERVICE AND ADJUSTMENTS TO REPLACE MOTION DRIVE BELT (See Fig. 32) TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 31) Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest. The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake. BELT REMOVAL • Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).
SERVICE AND ADJUSTMENTS TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT (See Fig. 33) TO ADJUST STEERING WHEEL ALIGNMENT If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steering wheel and reassemble per instructions in the Assembly section of this manual. The transaxle should be in neutral when the gear shift lever is in neutral (lock gate) position.
SERVICE AND ADJUSTMENTS REPLACING BATTERY (See Fig. 36) TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 37) WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from ac ci den tal grounding. • • • • • • • • • • Raise hood. Unsnap headlight wire connector. Stand in front of tractor.
STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING PROBLEM Will not start CAUSE 1. 2. 3. 4. 5. 6. 7. CORRECTION Out of fuel. Engine not “CHOKED” properly. Engine flooded. Bad spark plug. Dirty air filter. Dirty fuel filter. Water in fuel. 1. 2. 3. 4. 5. 6. 7. 8. Loose or damaged wiring. 9. Engine valves out of adjustment. Fill fuel tank. See “TO START ENGINE” in Operation section. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. Poor cut - uneven 1. 2. 3. 4. 5. Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, or trash under mower. Bent blade mandrel. Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels. 1. 2. 3. 4. 5. Replace blade. Tighten blade bolt. Level mower deck.
1. Fold this page along dotted line indicated above. 2. Hold page before you so that its left edge is vertically parallel to a tree trunk or other upright structure. 3. Sight across the fold in the direction of hill slope you want to measure. 4. Compare the angle of the fold with the slope of the hill. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees.
SERVICE NOTES 29
SERVICE NOTES 30
AVISO 30
AVISO 29
GUÍA SUGERIDA PARA MEDIR LAS PENDIENTES CON LA VISTA PARA UNA OPERACIÓN SEGURA P L E G AR A LO EST L A RGO A ES DE U N L A A PEN LÍNE DIE A P N U T NTE E DE ADA 1 5 GRA DOS SOLAMENTE ANDE CUESTA ARRIBA O CUESTA ABAJO Y NO ATRAVIESE EL CERRO 15 GRADOS MAX. ADVERTENCIA: Para evitar daños graves, haga funcionar su tractor arriba y abajo de las pendientes, nunca transversalmente con respecto a las pendientes. No cortar pendientes mayores de 15 grados.
PROBLEMA IDENTIFICACIÓN DE PROBLEMAS CAUSA 1. 2. 3. El corte disparejo 1. El motor continúa funcionando cuando el operador se baja del asiento con el embrague del accesorio enganchado Sistema de control que exige la presencia del operador –seguridad fallado. CORRECCIÓN 1. Revise el alambrado, los interruptores y la conexiones.Si no están correctas, pongase en contacto con un centro de servicio cualificado. PRECAUCIÓN: NO opere la máquina sino hasta haber corregido el problema. 4. 5.
PROBLEMA No arranca IDENTIFICACIÓN DE PROBLEMAS CAUSA Corta mucho césped, muy rápido. Aceleración en la posición de “ESTRANGULACIÓN” (CHOKE). Acumulación de césped, hojas y basura debajo de la segadora. Filtro de aire sucio. Nivel de aceite bajo/aceite sucio. Bujía fallada. Filtro de combustible sucio. Combustible rancio o sucio. 4. 5. 6. 7. 8. 1. 2. Pérdida de fuerza 1. 2. 3. 4. Batería baja o descargada Terminales de la batería corroídos. Alambrado suelto o dañado. Solenoide o arrancador fallados.
ALMACENAMIENTO Inmediatamente prepare su tractor para el almacenamiento al final de la temporada o si el tractor no se va a usar por 30 días o más. MOTOR SISTEMA DE COMBUSTIBLE Advertencia: Nunca almacene el tractor con gasolina en el estanque dentro de un edificio en donde los gases pueden alcanzar una llama expuesta o una chispa. Permita que el motor se enfríe antes de almacenarlo en cualquier recinto privado.
SERVICIO Y AJUSTES REEMPLAZAR LA BATERIA (Vea Fig. 36) ADVERTENCIA: No haga cortocircuito con los terminales de la batería al permitir que una llave de tuerca o cualquier otro objeto entre en contacto con ambos terminales a la misma vez. Antes de instalar la batería remueva las pulseras de metal, los relojes de pulsera de metal, los anillos, etc. El terminal positivo tiene que conectarse primero para evitar las chispas debido a la conexión a tierra por accidente.
SERVICIO Y AJUSTES REGULACIÓN DE LA POSICIÓN NEUTRO DE LA PALANCA DEL CAMBIO MECÁNICO (Vea Fig. 33) El cambio mecánico con diferencial y tracción anterior tiene que estar en posición neutro cuando la relativa palanca está en posición (cierre metálico. La regulación ya está predefinida por la Casa constructora, pero si es necesario efectuar más regulaciones, proceder de la siguiente manera: • Asegurarse que el cambio mecánico con diferencial y tracción anterior esté en posición neutro .
SERVICIO Y AJUSTES PARA CAMBIAR LA CORREA DE LA CUCHILLA DE LA SEGADORA (Vea Fig. 31) La correa de la cuchilla de la segadora se puede cambiar sin herramientas. Estacione el tractor en una superficie nivelada. Enganche el freno de estacionamiento. REMOCIÓN DE LA CORREA – Tire la correa alejándola de la segadora. • Haga salir la correa de las poleas del mandril y de las poleas de guía. • Remueva la segadora del tractor (Vea “PARA REMOVER LA SEGADORA” de esta sección de este manual).
SERVICIO Y AJUSTES IMPORTANTE: El piso debe quedar bien nivelado de lado a lado. Asegúrese de que los neumáticos estén inflados a la PSI que se indica en estos. Si están demasiado inflados o poco inflados, el césped no le quedará bien cortado, lo cual podrá llevarlo a pensar que la segadora no está bien regulada. AJUSTE DE DELANTE A ATRÁS (Vea Fig. 29 y 30) PARA NIVELAR LA SEGADORA REGULACIÓN VISUAL DE LADO A LADO (Vea Fig.
• • SERVICIO Y AJUSTES FIJE LOS BRAZOS DE SUSPENSIÓN LATERALES DE LA CORTADORA (A) AL CHASIS - Ubique el orificio del brazo encima de la clavija (B) que hay en la parte exterior del chasis del tractor, y fíjelo con una resorte de contención. Realice el mismo procedimiento en el otro lado del tractor. • Meta el fin de la conexión (E) en el hoyo en el suporte anterior de orificio y conecte con arandela e Retén del resorte (J). E A J F H B • Fig.
SERVICIO Y AJUSTES ADVERTENCIA: PARA EVITAR LESIÓNES SERIAS, ANTES DE DAR CUALQUIER SERVICIO O DE HACER AJUSTES: • Presione el pedal del embrague/freno completamente y aplique el freno de estacionamiento. • Ponga la palanca de cambios en la posición de neutro (N). • Ponga el embrague del accesorio en la posición desenganchado (DISENGAGED). • Ponga la llave de ignición en la posición de apagado (STOP) y remuévala. • Asegúrese que las cuchillas y que todas las partes movibles se hayan detenido completamente.
MANTENIMENTO SISTEMA DE ENFRIAMIENTO DE AIRE (Vea Fig. 18) Los escombros pueden atascar el sistema de enfriamiento de aire de motor. Remueva la cubierta del soplador y limpie el área mostrada para evitar el recalentamiento y daños al motor. REJILLA DE AIRE LIMPIEZA • • LIMPIE EL DESPERDICIO Y LOS ESCOMBROS Limpie todo material extraño del motor, la batería, el asiento, el pulido, etc. Limpie los desechos de la placa guía.
MANTENIMENTO CORREAS "V" Revise las correas "V" para verificar si existe deterioro y desgaste después de 100 horas de operación y cámbielas si es necesario. Las correas no son ajustables. Cambie las correas si empiezan a deslizarse debido al desgaste. ORIFICIO DE DRENAJE DEL ACEITE TAPÓN DE DRENAJE EXTENSOR DE DRENAJE DEL ACEITE ENFRIAMIENTO DEL TRANSEJE Mantenga el transeje sin acumulación de mugre o paja que puede restringir el enfriamiento.
TRACTOR MANTENIMENTO Siempre observe las reglas de seguridad cuando dé mantenimiento. OPERACIÓN DEL FRENO Si el tractor necesita más de cinco (5) pies (1,5 m) para detenerse a la máxima velocidad al cambio más alto en una superficie nivelada, de hormigón o pavimentada, hay que hacerle el servicio al freno. Vea “CONTROLAR Y AJUSTAR EL FRENO” en el capítulo de Servicio y ajustes de este manual. LLANTAS • • • Mantenga todos los neumáticos con la presión de aire adecuada. (Vea la PSI que se indica en estos.
MANTENIMENTO PROGRAMA DE MANTENIMIENTO ANTES DE CADA USO CADA 8 HORAS CADA 25 HORAS CADA 50 HORAS CADA 100 HORAS CADA TEMPORADA ALMACENAMIENTO Revisar la operación del freno Revisar la presión de las llantas T R A C T O R Verificar la sistemas presencia del operador y sistemas "ROS" Revisar si hay sujetadores sueltos Afilar/cambiar las cuchillas de la segadora 3 Tabla de lubricación Revisar el nivel de bateria 4 Limpiar la batería y los tereminales Limpie los residuos de la placa de dirección.
OPERACIÓN PARA HACER ARRANCAR EL MOTOR (Vea Fig. 4) Al hacer arrancar el motor por la primera vez o si se ha acabado el combustible del motor, se necesitará tiempo para el arranque extra para mover el combustible desde el estanque hasta el motor. • Siéntase en el sillón en la posición de operación, suelte el pedal del embrague/freno y ponga el freno de estacionamiento. • Ponga la palanca de cambio en la posición de neutro. • Mueva el embrague del accesorio a la posición "DESENGANCHADO".
OPERACIÓN FUNCIONAMIENTO ATRÁS (ROS) (Vea Fig. 12) Tu tractor está equipado con el Sistema de Funcionamiento Atrás (ROS). Cualquier tentativa del operador de viajar marcha atrás con el embrague puesto apagará el motor a menos que la llave de ignición se ponga en la posición de “ON” del ROS. ATENCIÓN: Ir marcha atrás con el embrague puesto para cortar, no es recomendable.
OPERACIÓN PARA AJUSTAR LA ALTURA DE CORTE DE LA SEGADORA (Vea Fig. 9) La posición de la palanca elevadora (A) determina a qué altura se cortará el césped. A PARA OPERAR LA SEGADORA Su tractor viene equipada con un interruptor sensor que exige la presencia del operador. Si el motor está funcionando y el embrague del accesorio está enganchado y el operador trata de bajarse del asiento, se apagará el motor.
OPERACIÓN La operación de cualquier tractor puede hacer que salten objetos extraños dentro de sus ojos, lo que puede producir daños graves en éstos. Siempre use anteojos de seguridad o protecciones para los ojos mientras opere su tractor o cuando haga ajustes o reparaciones. Recomendamos gafas de seguridad o una máscara de visión amplia de seguridad usada sobre las gafas. COMO USAR SU TRACTOR PARA AJUSTAR EL FRENO DE ESTACIONAMIENTO (Vea Fig.
OPERACIÓN FAMILIARICESE CON SU TRACTOR LEA ESTE MANUAL DE OPERARIO Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU TRACTOR Compare las ilustraciones con su tractor para familiarizarse con las ubicaciones de los diversos controles y ajustes. Guarde este manual para referencia en el futuro. H D G E B F A C J Fig. 4 Nuestros tractores cumplen con los estándares de seguridad del American National Standard Institute. (F) INTERRUPTOR DE IGNICIÓN - Se usa para hacer arrancar o hacer parar el motor.
OPERACIÓN Estos símbolos pueden aparecer sobre su tractor o en la literatura proporcionada con el producto. Aprenda y comprenda sus significados.
MONTAJE REVISIÓN DE LA PRESIÓN DE LAS LLANTAS Las llantas en su unidad fueron infladas demasiado en la fábrica por razones de envío. La presión de las llantas correctas es importante para obtener el mejor rendimiento en el corte. • Reduzca la presión de los neumáticos a la PSI que se indica en estos. REVISIÓN DE LA NIVELACIÓN DEL CONJUNTO Para obtener los mejores resultados en el corte, la caja de la segadora tiene que estar nivelada en la forma adecuada.
MONTAJE Ajuste el asiento antes de apretar la manilla de ajuste. • Remueva la manilla de ajuste y la arandela plana que aseguran el asiento al empaque de cartón y póngalos de lado para poder utilizarlos durante la instalación del asiento sobre el tractor. • Remueva y desechese del embalaje de cartón. • Colocar el asiento y en el asiento del recipiente de manera que la tres (3) cojíns esté posicionada en el agujero ancho ranurado en el recipiente.
MONTAJE Su tractor nuevo ha sido montado en la fábrica con la excepción de aquellas partes que no se han montado por razones de envío. Para asegurarse que su tractor funcione en forma adecuada y segura todas las partes y los artículos de ferretería que se monten tienen que ser apretados en forma segura. Use las herramientas correctas, según sea necesario, para asegurarse de que estén apretados en forma segura. HERRAMIENTAS NECESARIAS PARA EL MONTAJE Un juego de llaves de tubo facilitará el montaje.
PEDAZOS PARA LA MONTAJE Volante de dirección Inserto del volante de dirección (1) Arandela (1) Arandela de seguridad Volante de dirección (1) Perno hexagonal Adaptador Eje de Extención Accesorio de transción de la dirección Asiento (1) Manilla (1) Arandela (1) Asiento Extensión del aceite Llaves Batería Hoja de pendiente (2) Perno (2) Llaves (2) Tuerca 5
ESPECIFICACIONES DEL PRODUCTO FELICITACIONES por la compra de su tractor. Ha sido diseñado, planificado y fabricado para darle la mejor confiabilidad y el mejor rendimiento posible. • 62-75 Nm 45-55 Ft. Lbs. Torsión del Perno de la Cuchilla: • • Amp/Hr: Min. CCA: Modelo Tamaño: Batería: 3 Amps Bateria 5 Amps Luces Sistema de Carga: Champion RC12YC (Abertura: 0,76 mm / .
• REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles Mantener la máquina libre de hierba, hojas u otros escombros que pueden tocar el tubo de escape / partes del motor calientes y quemarse. No permitir que el puente del cortacésped cargue hojas u otros residuos que pueden causar acumulaciones. Limpiar toda salpicadura de aceite o carburante antes de hacer operaciones sobre la máquina o guardarla. Dejarla enfriar antes de guardarla. III.
REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles PELIGRO: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE. • • • • ADVERTENCIA: No avance cuesta abajo a punto muerto ya que podría perder el control del tractor.
MANUAL IMPORTANTE NO TÍRALO A FUERA MANUAL DE OPERARIO MODEL: ADVERTENCIA: Leer, entender y seguir todas las instrucciones sobre la máquina y en el manual antes de empezar. Si no se observan las instrucciones de seguridad siguientes se pueden producir lesiones graves o la muerte. PP175G42 TRACTOR PARA CÉSPED SIEMPRE USE PROTECCIONES PARA LOS OJOS MIENTRAS OPERE ESTE TRACTOR Vea la página web: www.poulanpro.