Headphones 4000 Series TAT4506 User manual Register your product and get support at www.philips.
Contents 1 Important safety instructions 2 Hearing Safety General information 2 2 2 Your True wireless earpieces 3 What's in the box Other devices Overview of your True wireless earpieces 3 Get started 3 3 4 5 Charge the battery 5 Pair the earpieces with your Bluetooth device for the first time 6 4 Use your earpieces Connect the earpieces to your Bluetooth device Control ANC (active noise cancelation) Manage your calls and music LED indicator status Voice Assistant 7 7 7 8 8 9 5 Reset the earp
1 Important safety instructions Hearing Safety Danger To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your headphones. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume continuously upwards as your hearing adapts.
2 Your True wireless earpieces Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/support. With this Philips True wireless earpieces, you can: • enjoy convenient wireless handsfree calls; • enjoy and control wireless music; • switch between calls and music. Quick start guide Global Warranty Safety leaflet What's in the box Other devices A mobile phone or device (e.g.
Overview of your True wireless earpieces Microphone Multi-function touch LED indicator (Earpieces) LED indicator (charging box) USB-C charging slot
3 Get started Charge the battery Note Before you use your earpieces for the first time, place the earpieces in the charging box and charge the battery for 2 hours for optimum battery capacity and lifetime. Use only the original USB-C charging cable to avoid any damage. Finish your call before charging the earpieces, as connecting the earpieces for charging will power the earpieces off. Charging Box Connect one end of the USB cable into the charging box, and another end into the power source.
Pair the earpieces with your Bluetooth device for the first time Enter the earpieces password “0000” (4 zeros) if prompted. For those Bluetooth devices featuring Bluetooth 3.0 or higher, no need to enter a password. Make sure that the headphones is fully charged and powered off. Philips TAT4506 Open the top cover from charging box. Single earpiece (Mono mode) Take either right or left earpiece out from charging box for Mono use. The earpiece will power on automatically.
4 Use your earpieces Control ANC (active noise cancelation) Connect the earpieces to your Bluetooth device Different ANC mode can be toggled via double tap on the right earpiece. Enable ANC • Turn on the Bluetooth function of your Bluetooth device. • Open the top cover from charging box. • ANC function is auto active when put into the ear. Touch the MFB button twice, it will change to Awareness mode. Touch the MFB button twice again, it will turn the ANC function off. The blue LED flashes.
ANC LED indicator status Call control Headphones status Indicator ANC mode is The blue LED will toggled turn on. Task Hang up call Right /Reject call earpiece Power on/off Task Multifunction button Turn the earpieces off.
Charging Box (4 blue LED) Charging Box LED (USB on) Indicator Battery LED indicator on Bluetooth device It will show a battery indicator on Bluetooth device after connected to earpieces.
5 Reset the earpieces TAT4506 Return earpieces to charging box & open the lid. Short press twice on casing button. 5 Follow steps in “Use your earpieces-Connect the earpieces to your Bluetooth device.” 6 Pair the earpieces with your Bluetooth device, select Philips TAT4506. 6 Technical data Music time: 6 hours Talk time: 6 hours Standby time: 200 hours Charging time: 2 hours Lithium-ion battery 50 mAh on each earpiece, Lithium-ion battery 500 mAh on charging box Bluetooth version: 5.
7 Notice Declaration of conformity Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www.p4c.philips.com. Remove the integrated battery If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headphones.
Compliance with EMF This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields. Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
8 Trademarks Bluetooth The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners. Siri Siri is a trademark of Apple Inc., registered in the U.S. and other countries. Google Google and Google Play are trademarks of Google LLC.
9 Frequently asked questions My Bluetooth earpieces do not turn on. The battery level is low. Charge the earpieces. I cannot pair my Bluetooth earpieces with my Bluetooth device. The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the earpieces. Pairing does not work. • Put both earpieces into charging box. • Make sure you have disabled the Bluetooth function of any previously connected Bluetooth devices.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product. UM_TAT4506_00_EN_V1.
