SHB2505 User manual Register your product and get support at www.philips.
Contents 1 Important safety instructions 2 Hearing Safety General information 2 2 2 Your Bluetooth wireless headset What's in the box Other devices Overview of your Bluetooth wireless headset 3 Get started Charge the battery Pair the headset with your Bluetooth device at the first time Pair the headset with another Bluetooth device 4 Use your headphones Reconnect the headset to your Bluetooth device Power on/off Manage your calls and music LED indicator status How to wear 5 Factory reset the headset
1 Important safety instructions Hearing Safety Danger To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your headset. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume continuously upwards as your hearing adapts.
2 Your Bluetooth wireless headset Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. With this Philips wireless headset, you can: • enjoy convenient wireless handsfree calls; • enjoy and control wireless music; • switch between calls and music.
Overview of your Bluetooth wireless headset Microphone Multi-function buttons LED indicator (headset) Micro USB charging slot LED indicator (charging case)
3 Get started • • Charging process is verified by white LED light on the earpieces. When the headset is fully charged, the white light goes off. Charge the battery Note Before you use your headset for the first time, place the headsets in the charging case and charge the battery for 3 hours for optimum battery capacity and lifetime. Use only the original USB charging cable to avoid any damage.
In right headset, it has voice “Pairing” and LED flashes in white and blue. The headset is now in pairing mode and is ready to pair with a Bluetooth device (e.g. a mobile phone). Turn on the Bluetooth function of your Bluetooth device. Pair the headset with your Bluetooth device. Refer to the user manual of your Bluetooth device. In right headset, it has voice “Connected” and LED stays on for 5 seconds on both headsets. You can use your device to play music or make a call.
4 Use your headset Connect the headset to your Bluetooth device Turn on the Bluetooth function of your Bluetooth device. Take both headsets from the charging case, the headset will power on and reconnect automatically. If no device is connected, the headset will automatically turn off after 3 mins. Both headsets are now powered on and are paired with each other automatically. Power on/off Task Multifunction button Operation Turn the Headsets headset on. Take both headsets from the charging case.
Call control Task Multifunction button Pick up/hang Right/Left headset up call Reject an Right/Left incomging headset call Switch caller Right/Left during a call headset Operation Siri/Google You will hear ‘battery low’ on the headset. The white LED flash twice for every 3 minutes. Battery is fully charged. The LED is off. Press once Press and hold for 2 seconds Press and hold for 2 seconds Battery LED indicator on headset status Voice control Task Low battery level (headset).
Battery LED indicator on Charging case with USB cable While charging headset, Blue LED status as below: 4 blue LED stay on for 75-100% power 2 blue LED stay on and 3rd LED flashes every second for 50-75% power 1 blue LED stay on and 2nd LED flashes every second for 25-50% power 1 blue LED flashes every second for 0-25% power 5 Factory reset the headset If you encounter any pairing or connection issue, you can follow the following procedure to factory reset your headset.
6 Technical data Headset Music time: 3 hours (additional 9 hrs with charging case) Talk time: 2.5 hours (additional 7 hrs with charging case) Standby time: 60 hours Charging time: 2 hours Rechargeable lithium ion battery: 50 mAh on each earpiece Bluetooth version: 5.0 Compatible Bluetooth profiles: • HSP (Hands-Free Profile-HFP) • A2DP (Advanced Audio Distribution Profile) • AVRCP (Audio Video Remote Control Profile) Supported audio codec: SBC Frequency range: 2.
7 Notice Declaration of conformity Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www.p4c.philips.com. Remove the integrated battery If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headphones.
Compliance with EMF This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields. Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company.
8 Frequently asked questions My Bluetooth headset does not turn on. The battery level is low. Charge the headset. I cannot pair my Bluetooth headset with my Bluetooth device. The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the headset. Pairing does not work. • Put both earpieces into charging case. • Make sure you have disabled the Bluetooth function of any previously connected Bluetooth devices.
I hear but cannot control music on my Bluetooth device (e.g. play/pause/skip forward/backward). Make sure the Bluetooth audio source supports AVRCP (see ‘Technical data’ on page 10). The volume level of the headset is toot low. Some Bluetooth devices cannot link the volume level with the headset through volume sync. In this case, you have to adjust the volume on your Bluetooth device independently to achieve an appropriate volume level.
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados. Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução 242/2000, e atende aos requisitos técnicas aplicados. Para maiores informações, consulte a site da ANATEL: www.anatel.gov.br Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license.