QC5570
1 7 2 3 8 4 9 5 10 6 11 13 12
empty page before TOC
English 6 简体中文 20
English Introduction Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. Your new Philips hair clipper with new ergonomic design and 180º adjustable cutting element allows you to clip your own hair easily. You can move the clipper over all areas of your head as easily as running your fingers through your hair. To enjoy using the hair clipper, we advise you to read the following information.
English 7 Danger - Keep the supply unit dry. Warning - To charge the battery, only use the detachable supply unit (HQ8505) provided with the appliance. - The supply unit contains a transformer. Do not cut off the supply unit to replace it with another plug, as this causes a hazardous situation.
English Caution - Never immerse the charging stand in water and do not rinse it under the tap. - Never immerse the appliance in water. Do not use the appliance in the bath or shower. - Never use water hotter than 60°C to rinse the appliance. - Only use this appliance for its intended purpose as shown in the user manual. - For hygienic reasons, the appliance should only be used by one person.
English 9 Note: Charge the appliance for at least 1 hour before you use it for the first time or after a long period of non-use. Charging takes approx. 1 hour. A fully charged appliance has a operating time of up to 60 minutes. Note: This appliance can be used cordless or directly from the wall socket. Battery charge indicator - When the battery is almost empty, the battery charge indicator flashes orange. - When the appliance is charging, the battery charge indicator on the appliance flashes white.
English fully recharge the battery. Before first use 1 1 Pull the front of the cutting element upwards and remove the cutting element from the appliance. 2 2 Turn the cutting element and lubricate the three points indicated with oil from the oil bottle supplied. Using the appliance This appliance can be used cordless or directly from the wall socket. Preparing for use Make sure your hair is clean and dry. 1 Comb your hair with a styling comb in the direction of hair growth.
English 11 - Since all hair does not grow in the same direction, you need to move the appliance in different directions (upwards, downwards and across). - Make sure that the flat part of the comb attachment is always fully in contact with the scalp to obtain an even result. - Write down the settings you use to create a certain hairstyle as a reminder for future clipping sessions.
English Hair clipping with comb 1 Insert the edge of the comb attachment into the swivel head. Make sure the comb attachment locks into position properly. Note: The length settings are indicated on the comb attachment. – 3 mm – 5 mm – 7 mm 2 Turn the length setting adjustment ring to set the comb attachment to the desired setting. The arrowhead on the appliance indicates which setting you have selected.
English 13 6 Regularly remove cut hair from the comb attachment. If a lot of hair has accumulated in the comb attachment, remove the comb attachment from the appliance and blow and/or shake the hair out of it. When you remove the comb attachment, the selected setting does not change. Contouring without comb You can use the appliance without comb attachment to clip your hair very close to the skin (0,5mm) or to contour the neckline and the area around the ears.
English 5 To contour the neckline and the sideburns, turn the appliance and make downward strokes. Note: Move the appliance slowly and smoothly. Just follow the natural hairline. 6 Adjust the position of the swivel head to make contouring easier (see 'Using the swivel head '). Cleaning and maintenance Regular cleaning guarantees better grooming results. Never clean, remove or replace a shaving or cutting unit while the appliance is switched on.
English 15 4 Place your thumb in the center of the round side of the cutting element and your index finger on the teeth of the cutting element. Use your index finger to lift the cutting element from the swivel head. 1 2 5 Rinse the cutting element under the tap or clean it with the cleaning brush supplied. 6 Rinse the inside of the appliance under the tap or clean it with the cleaning brush supplied.
English 2 Turn the cutting element and lubricate the three points indicated. Storage 1 Switch off the appliance and disconnect it from the mains. 2 Store the appliance and its accessories in the storage pouch supplied. Ordering accessories To buy accessories or spare parts, visit www.philips.com/parts-and-accessories or go to your Philips dealer. You can also contact the Philips Consumer Care Center in your country (see the international warranty leaflet for contact details).
English 17 - Follow your country’s rules for the separate collection of electrical and electronic products and rechargeable batteries. Correct disposal helps prevent negative consequences for the environment and human health. Removing the rechargeable battery Only remove the rechargeable battery when you discard the product. Before you remove the battery, make sure that the product is disconnected from the wall socket and that the battery is completely empty.
English information below, visit www.philips.com/support for a list of frequently asked questions or contact the Consumer Care Center in your country. Problem Possible cause Solution The appliance produces an uneven cutting result. The comb does not touch the skin when you move the appliance through the hair. Make sure the comb is always fully in contact with the skin when you move the appliance through the hair. You only move the appliance in one direction.
English Problem Possible cause 19 Solution I do not know how to change the hair length settings of the comb attachments. You can change the hair length settings of the comb attachments with the length setting adjustment ring on the appliance. Turn the ring to set the comb attachment to the desired setting. See chapter ‘Using the appliance’, section ‘Hair clipping with comb’ One of the comb attachments is damaged or worn. Do not use the comb attachment anymore.
简体中文 简介 感谢您的惠顾,欢迎光临飞利浦! 为了让 您能充分享受飞利浦提供的支持,请在 www.philips.
简体中文 21 重要安全信息 使用本产品及其附件之前,请仔细阅读本 重要信息,并妥善保管以供日后参考。 随 附的附件可能因产品而异。 危险 - 保持电源部件干燥。 - 警告符号注释: 禁止在打开的水龙头下 进行清洗。 警告 - 要给电池充电,请仅使用产品随附的可 拆卸电源部件 (HQ8505)。 - 电源部件中包含一个变压器。 请勿自行 更换电源部件的插头,否则将导致严重 后果。 - 本产品也可以由 8 岁或以上年龄的儿童 以及肢体不健全、感觉或精神上有障碍 或缺乏相关经验和知识的人士使用,但 前提是有人对他们使用本产品进行监督 或指导,以确保他们安全使用,并且让 他们明白相关的危害。 切勿让儿童玩弄 本产品。 不要让儿童在无人监督的情况 下对本产品进行清洁和保养。 - 手持部分与电源软线分开后,才能在水 中清洗手持部分。
简体中文 - 使用前,请务必检查产品。 请勿使用损 坏的产品,否则可能对人体造成伤害。 请务必用原装型号更换损坏的部件。 - 本产品包含的电池不可更换。 - 切勿拆开本产品更换充电电池。 警告 - 切勿将充电座浸入水中,也不要在自来 水龙头下冲洗。 - 切勿将产品浸入水中。 请勿在洗澡或淋 浴时使用本产品。 - 切勿使用温度高于 60°C 的热水冲洗 本产品。 - 只能将本产品用于用户手册中所示的原 定用途。 - 出于卫生的目的,本产品只能供一个人 使用。 - 请勿在包含电动空气清新器的墙壁插座 上或其周围使用电源部件,以免电源部 件受到不可修复的损坏。 - 切勿使用压缩气体、钢丝绒、研磨性清 洁剂或腐蚀性液体(例如汽油或丙酮) 来清洁产品。 电磁场 (EMF) 本 Philips 产品符合所有有关暴露于电磁 场的适用标准和法规。
简体中文 23 概述 - 该产品可放心在水龙头下清洗。 - 符号注释:适合用在打开的水龙头下进 行清洗。 - 电源部件适合在 100 - 240 伏的电源电 压下工作。 - 该电源部件可将 100-240 伏的电压转换 为 24 伏以下的安全低电压。 充电 第一次使用本产品之前,以及当电池状态 指示灯指示电池电量快要耗尽 (请参见 '电 池充电指示灯')时,请为本产品充电。 注意: 首次使用前或长时间不用之后,请 为产品至少充电 1 小时。 充电约需 1 小时。充满电的产品最长可使 用 60 分钟。 注意: 本产品可以不接电源或直接连在插 座上使用。 电池充电指示灯 - 当电池的电量几乎耗尽时,电池充电指 示灯会呈橙色闪烁。 - 产品充电时,其电池充电指示灯呈白色 闪烁。 - 电池充满电后,电池充电指示灯将呈白 色持续亮起。 注意: 电池充满电后,电池充电指示灯将 在大约 30 分钟后自动关闭。
简体中文 使用电源部件充电 1 将小插头插入本产品,然后将电源部件 插入电源插座。 电池充电指示灯指示产品正在充电 (请 参见 '电池充电指示灯')。 2 充电之后,从电源插座上拔下电源部 件,并从本产品上拔下小插头。 注意: 电池充满电后,电池充电指示灯将 在大约 30 分钟后自动关闭。 优化充电电池寿命 每年将充电电池彻底放电两次, 方法是让马达一直转动,直到不再转为 止。 然后 将电池再次完全充电。 首次使用之前 1 将修剪部件前端向上拉,然后从产品上 取下修剪部件。 1 2 2 转动修剪部件,用随附油瓶中的油润滑 所示的三个位置。
简体中文 25 使用本产品 本产品可以不接电源或直接连在插座上使 用。 使用准备 确保头发清洁干燥。 1 使用定型梳沿头发生长的方向梳理头 发。 头发修剪提示 - 建议您从常规梳齿附件的最高设置开始 修剪,然后逐渐缩短设置。 - 要获得最大修剪效率,请沿头发生长的 反方向移动本产品。 - 因为头发不会全部以相同的方向生长, 您需要以不同的方向移动产品(向上、 向下或交叉)。 - 确保梳齿附件的扁平部分完全接触到头 皮,以获得均匀的修剪效果。 - 记下您使用的设置,用作以后剪发过程 中打造某种发型的参考。 使用旋转头 90˚ 45˚ 0˚ 90˚ 18 0° 45˚ 您可以将旋转头从开始位置 0°(指向前 方)向左或向右旋转 45° 或 90°。 您可 以通过这种方法调整修剪部件,以贴合待
简体中文 修剪头发部位的头部轮廓。 这使您可以更 轻松地为自己理发。 1 要将修剪部件设置到所需位置,请转动 旋转头(可听到“咔哒”一声)。 注意: 始终通过转动旋转头调整修剪部 件的位置。 请勿转动修剪部件或梳齿附 件。 注意: 请勿向左或向右转动旋转头超过 90°。 您可以像握持定型梳一样握住旋转头来 使用本产品。 使用修剪梳修剪头发 1 将梳齿附件的边缘插入旋转头。 确保梳齿附件正确锁定到位。 注意: 梳齿附件上指示长度设置。 – 3 mm – 5 mm – 7 mm
简体中文 27 2 旋转长度设置调整环,将梳齿附件设为 所需设置。 产品上的箭头表示您选择的设置。 7 5 2 1 提示: 使用不同设置在从颈部到头顶的 各种头发长度之间实现自然顺利的过 渡。 切勿将长度设置调整环转到最高设置之 外。 3 在修剪不同位置的头发 (请参见 '使用旋 转头 ')时,可以将旋转头转动到您的手 臂感觉最舒服的位置。 4 按开/关按钮启动产品。 QC5570: 短暂地按下按钮。 QC5580: 按住按钮 2 秒钟。 5 将理发器在头发上缓慢移动。 6 定期清除梳齿附件中剪下的头发。 如果梳齿附件中积聚了许多头发,请先 取下梳齿附件,吹去和/或抖掉梳齿附件 上的头发。 取出梳齿附件时,所选的设 置不会改变。 不用梳齿的情况下修剪轮廓 即使没有梳齿附件,您也可以使用理发器 以非常贴近头皮的距离(0.
简体中文 密贴合颈部周围和双耳附近的皮肤修剪头 发。 由于修剪部件会去除接触到的每一根头 发,因此在没有梳齿附件修剪头发时要小 心。 1 将梳齿附件从旋转头拉出。 切勿拔扯梳齿附件容易变形的顶部。 请 务必拉拔底部。 2 在开始紧贴双耳附近的发线修剪头发之 前,请梳理耳朵上方的发梢。 3 按开/关按钮启动产品。 4 修整耳朵周围的轮廓时,倾斜产品,使 修剪部件只有一边接触发梢。 5 要紧贴颈部周围和鬓角轮廓,请转动产 品并向下修剪。 注意: 缓慢、流畅地移动产品。 只需 顺着自然生长的发际线。 6 调整旋转头的位置,使修剪轮廓更容易 (请参见 '使用旋转头 ')。 清洁和保养 为保证更好的修剪效果,请定期清洗剃 毛刀。
简体中文 29 切勿在产品开启时清洗、拆卸或更换剃 毛或修剪部件。 切记先检查水温是否太高,以防烫手。 切勿使用毛巾或纸巾擦干修剪部件或剃 毛刀网,因为有可能造成损坏。 切勿使用压缩气体、钢丝绒、研磨性清 洁剂或腐蚀性液体(例如汽油或丙酮) 清洁本产品。 每次用完产品后,请在水龙头下冲洗产品 或用随附的清洁刷进行清洁。 在自来水龙头下清洗剃须刀之前,务必拔 掉其电源插头。 小心不要让修剪部件掉落在地板上。 1 关闭产品并断开电源。 2 取下发梳。 3 在水龙头下冲洗梳齿附件或用随附的清 洁刷进行清洁。 1 2 4 将拇指放在修剪部件的圆边中心,食指 放在修剪部件的齿上。 使用食指从旋转 头提起修剪部件。
简体中文 5 在水龙头下冲洗修剪部件或用随附的清 洁刷进行清洁。 6 在水龙头下冲洗产品的内部或用随附的 清洁刷进行清洁。 7 将修剪部件的凸缘插入槽内,然后将修 剪部件推回旋转头。 1 2 润滑修剪部件 每 3 个月用产品随附的油瓶中的油润滑一 次修剪部件。 1 将修剪部件前端向上拉,然后从产品上 取下修剪部件。 1 2 2 转动修剪部件并润滑所示的三个位置。
简体中文 31 存放 1 关闭产品并断开电源。 2 将产品及其附件存放在随附的存储袋 中。 订购配件 如需购买附件或备件,请访问 www.philips.
简体中文 当您使用工具打开本产品时以及在您弃置 充电电池时,请采取必要的安全保护措 施。 1 断开产品电源并让产品继续运行,直到 马达停止。 2 去除产品的上顶盖部分。 3 使用螺丝刀打开产品内部主体。 4 使用螺丝刀从产品取下充电电池。 5 使用家用剪刀剪断电线。 ˌɫǩ؆ (Pb) мȞġĈҴˀΙĀǩ؆Ӎߒʔ ĈҴˀΙ ᰽ ⬡ ԣ͍Ჱ Ġ⅑ԓ᧠ Ġ⅑ȕ᧠⓭ (Hg) (Cd) (Cr (VI) ) (PBB) (PBDE) PCB’s X O O O O O מŪǗɢذ Electrical contact pins X O O O O O ǗˈਝǦ Power plug X O O O O O Ǘ۷Ǽ Internal metal parts X O O O O O ʭˌ̇͒ɫ ǕȪϜ֪֙SJ/T 11364Āܪǭৠ̑뺯 O ȪФ˽ĈҴˀΙć˽ˌɫǨĈߴΙࠒնġĀߒʔߴćGB/T 26572ܪǭĀՄʔđ̂ŘĪ뺯 X ȪФ˽ĈҴˀΙψɺć˽ˌɫĀԚĂߴΙࠒնġĀߒʔɸŜGB/T 26572ܪǭĀՄʔđ̂뺯 - 该表格中所显示的“有害物质”在产品
简体中文 33 故障处理方法 问题 产品的修剪效 果不均匀。 本章归纳了使用本产品时最常见的一些问 题。 如果您无法根据以下信息解决问题, 请访问 www.philips.
简体中文 问题 可能的原因 解决方法 如果修剪部件和 清洁修剪部件和修剪 修剪梳不干净, 梳。 修剪性能会下 降。 启动产品后, 产品无法工 作。 产品没有连接电 将充电插头插入产 源插座。 品,然后将电源部件 插入电源插座。 我不知道如何 将梳齿附件连 接至产品。 要连接梳齿附件,只 需将其滑入产品的插 槽中即可。 我不知道如何 更改梳齿附件 的头发长度设 置。 您可使用产品上的长 度设置调整环 更改梳齿附件的头发 长度设置。 旋转调整 环,将梳齿附件设为 所需设置。 请参 阅“使用产品”一章 的“使用修剪梳修剪 头发”部分 其中一个梳齿 附件损坏 或磨损。 切勿再使用梳齿附 件。 请使用原装型号 的附件或梳齿更换。 您可以从当地的飞利 浦经销商获得替换梳 齿附件,或访问 www.philips.
简体中文 35 保修和支持 如需信息或支持,请访问 www.philips.
简体中文 保留备用 发行日期: 11/9/2018
Empty page before back cover
© 2018 Koninklijke Philips N.V. All rights reserved 保留所有权利 4222.002.8362.