DC200_Eng 2008.2.15 11:20 Page 1 Docking Entertainment System Register your product and get support at www.philips.
DC200_Eng 2008.2.15 11:20 Page 2 Important notes for users in the U.K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fix new fuse which should be a BS1362 3 Amp, A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place.
DC200_Eng 2008.2.
DC200_Eng 2008.2.
DC200_Eng 2008.2.15 11:20 Page 5 English Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. SUPPLIED ACCESSORIES – 1 X certified AC/DC 9V adaptor (Brand name: PHILIPS, Model No.: AS140-090-Dw, Input: 100-240V ~ 50/60Hz 0.7A, Output: 9.0V 1.
DC200_Eng 2008.2.15 11:20 Page 6 OK for iPod . . . . . . . . . . . . . .confirms menu selection.
DC200_Eng 2008.2.15 11:20 Page 7 POWER SUPPLY Mains adaptor 1 Connect the mains adaptor to the set's DC 9V socket and to the power socket. Helpful hints: To avoid damage to the set, use only the adaptor supplied! The power rating is located on the bottom of the set. SELF-POWERED BACK-UP The self-powered back-up conveniently allows your alarm and clock time settings to be stored for up to 10 minutes when there is a power interruption e.g. AC power failure.
DC200_Eng 2008.2.15 11:20 Page 8 5 Press PROG/SET TIME to confirm. 6 In clock mode, press ALBUM/PRESET -/+ 1 /2 to set your time zone. 7 To zoom in/out the clock display, press MODE in clock mode. TUNER 1 Press SOURCE repeatedly to switch on the radio (FM only). ™ Display shows the radio frequency of the last selected waveband. Your preset station is also shown if you are listening to a preset. (See 2) 2 Adjust the sound using VOLUME 3 /4.
DC200_Eng 2008.2.15 11:20 Page 9 USING THE ALARM GENERAL Two different alarm times can be set. This can be useful when you need to be woken up at a different time e.g. during the week and at the weekend, and you can set different wake-up modes: • Tuner mode. • iPod/USB mode. • Nature sound mode. • Buzzer mode. The gentle wake buzzer alarm increases its beep tone frequency within seconds. SETTING THE ALARM TIME AND MODE (See 3) 1 In any mode, press and hold 1 ALM or 2 ALM for two seconds.
DC200_Eng 2008.2.15 11:20 Page 10 SWITCHING OFF THE ALARM There are three ways of switching off the alarm. Unless you cancel the alarm completely, the 24-hour ALARM RESET will be automatically selected after 59 minutes from the time your alarm first goes off. 24 HOUR ALARM RESET If you want the alarm mode to be stopped immediately but also wish to retain the same alarm setting for the following day: • Press POWER or 1 ALM / 2 ALM. REPEAT ALARM This repeats your alarm call at 9 minute intervals.
DC200_Eng 2008.2.15 11:20 Page 11 PLAYING iPod USING DC200 1 Remove the top cover of dock. 2 Snap the compatible iPod into the dock connector. 3 Press SOURCE repeatedly to switch on the iPod mode. • Make sure that you have powered on Apple iPod before selecting iPod source. ™ On the DC200’s display, “iPod” is displayed when iPod is connected. 4 The connected iPod player will play automatically.
DC200_Eng 2008.2.15 11:20 Page 12 Notes: In some USB flash players (or memory devices), the stored contents are recorded using copyright protection technology. Such protected contents will be unplayable on any other devices (such as DC200 device).
DC200_Eng 2008.2.15 11:20 Page 13 ™ The current album number flashes. 3 Press ¡1 / 2™ to select a desired album number. 4 Press PROG to confirm. ™ The current track number flashes. 5 Press ¡1 / 2™ to select a desired track number. 6 Press PROG to confirm. 7 Repeat steps 3-6 to select and store all desired tracks. 8 To start playback of your programme, press 2;. Helpful hints: – Up to 999 playable audio files stored on a USB mass storage device can be played on DC200.
DC200_Eng 2008.2.15 11:20 Page 14 directly set the sleep function. CONNECTING AN EXTERNAL DEVICE You can listen to the sound of the connected external device through your DC200’s speakers. 1 Press SOURCE repeatedly to select AUX mode. 2 Use the supplied AUX-IN cable to connect DC200’s AUX IN jack to an AUDIO OUT or headphone jack on an external equipment (such as CD player, or VCR). MAINTENANCE & SAFETY • Install the unit near the AC outlet and where the AC power plug can be easily reached.
DC200_Eng 2008.2.15 11:20 Page 15 TROUBLESHOOTING If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. WARNING: Under no circumstances should you try to repair the set yourself, as this will invalidate the guarantee.
DC200_Eng 2008.2.15 11:20 Page 16 Environmental information All unnecessary packaging material has been omitted. The packaging can be easily separated into three materials: cardboard, polystyrene and plastic. Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging, dead batteries and old equipment.
DC200_Eng 2008.2.15 11:20 Page 17 Meet Philips at the Internet http://www.philips.
