Register your product and get support at www.philips.com/welcome CED780 User manual CED780_05_UM_V1.0.
1 Important Safety Notice 2 Your in-car entertainment system Introduction What's in the box Overview of the main unit Overview of the remote control 5 5 5 7 7 7 9 7 Play with Bluetooth device Pair the Bluetooth-enabled devices Make a call Receive call Bluetooth phone book settings Favorite call Adjust Bluetooth settings Listen to music from Bluetooth device 10 8 Play iPod/iPhone 3 Get started Install the car audio Mount into the dashboard Attach the front panel Install remote control battery Turn on Se
12 Product information USB playability information 13 Troubleshooting About the Bluetooth device 4 38 39 40 40 EN CED780_05_UM_V1.0.
Safety Notice Read and understand all instructions before you use the device. If damage is caused by failure to follow instructions, the warranty does not apply. Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. The device is designed for negative ground (earth) 12 V DC operation only. not watch video when driving.
packaging materials, exhausted batteries and old equipment. ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary $ % & * % ® device that plays DivX video. Visit divx.com for more information and software & * ABOUT DIVX VIDEO-ON-DEMAND: This & * % ® device must be registered in order to play purchased DivX Video-onDemand (VOD) movies.
Copyright 2012 © Koninklijke Philips Electronics N.V. < = notice. Trademarks are the property of Koninklijke Philips Electronics N.V or their respective owners. Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. 2 Your in-car entertainment system Eng l i s h Never dispose of your product with other household waste.
a i Remote control battery b j Rubber cushion k User manual l Quick start guide c d e f g h i j k l a Main unit and front panel (with a sleeve) b Remote control c Trim plate d Carrying case for front panel e ISO standard connector f Audio and Video cable g Hexagon head screw h Screws - M4x8mm (x4) 8 EN CED780_05_UM_V1.0.
Eng l i s h Overview of the main unit ab c d e g f h i j k o n m l q p a OPEN Open/Close TFT screen. b Press to answer a call. Press and hold to transfer call. c / Turn the unit on or off. Mute or unmute sound. Rotate to adjust volume. d BAND Select tuner band. e +/-PRESET Select preset radio station. Search for track/folder. f DISP Adjust dimmer settings. Press and hold to turn off TFT display. g TILT Adjust position of the screen. h Eject disc.
External audio/video socket. k Unlock the panel. Overview of the remote control l a b c d USB socket. m SOURCE Select source. e n Press to terminate call. o / Tune for radio station. Skip/search for track. Fast backward/forward playback. ~ } | f g h i { z y j k p RESET Reset the unit when it hangs up. x l q SD/SDHC card slot u m n t o s p r q w v a Turn the unit on or off. b NAVI Enter GPS navigation system. c SOURCE Select source.
x Turn maximizing sound on or off. i DVD MENU Access DVD main menu. / Skip to previous/next track/chapter. Move cursor to left/right. Eng l i s h h y Turn TFT on or off. j Turn full sound on or off. z DVD AUDIO Select audio language or audio channel. Return to previous menu or exit. { TOP MENU Return to top menu. k l DBB Turn Dynamic Bass Boost (DBB) sound on or off. | TILT +/ Adjust position of the screen. m EQ Access audio setting menu.
3 Get started Caution Notes on speaker connection Never connect speaker wires to the metal body or chassis of the car. Never connect speaker wires with stripes to one another. Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. Always follow the instructions in this chapter in sequence. Install the car audio Connect wires Caution Ensure that all loose leads are insulated with electrical tape.
5 6 7 8 2 Connector Connect to Red wire The +12V power terminal which is live in the accessory (ACC) position of the ignition switch. If there is no accessory position, connect to the +12V car battery terminal that is always live.
22 21 20 1 5 8 7 6 2 9 0! " § $ % & / 18 19 3 4 14 EN CED780_05_UM_V1.0.
Connect to/with Extension wire Parking brake (-) 3 4 5 6 7 8 Pink wire Extension wire (not included) Brake switch Ground Purple wire Gearbox switch Reverse gear signal ISO wires 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Yellow cable Red cable White cable Red cable White cable Red cable White cable Yellow cable Brown cable Blue cable White wire Black wire Black wire Black wire 2 Ensure that car dashboard opening is within these measurements: Reverse camera (B+) Black lamp lead + Connected in step 1 ab
Attach the front panel 5 Install the sleeve into the dashboard and = Z Slide the unit into the dashboard until you hear a click. 1 Attach the trim plate. 2 Insert the left side of the panel in the chassis until it is correctly engaged. 3 Press the right side of the panel until the mechanism locks it into place. Note ? Z = Install remote control battery sleeve, skip this step.
Open the battery compartment. 2 Insert one CR2025 battery with correct polarity (+/-) as indicated. 3 Close the battery compartment. Eng l i s h 1 4 Tap [Finish] " Turn on Caution Risk of road accidents! Never watch videos or adjust settings while you drive. 1 Press to turn the unit on. » The available OSD (On-Screen Display) languages are displayed. 2 = » The OSD language is changed to the selected language immediately.
2 Tap to display the full menu. 4 Play audio/ video/picture Load discs 3 4 Tap . » The setup menu is displayed. You can play video, audio or images stored on the following discs: DVD video, DVD-R, DVD-RW VCD Audio CD, CD-R, CD-RW 1 Insert the disc into the disc slot with label side facing up. » The disc starts playing automatically. 2 To remove the disc, press the button. » When the disc is ejected, the unit switches to the previous source, if connected.
Supported DVD region code 3 China To remove the USB device, switch the car " take off the USB device. » When USB device is disconnected, it plays the previous source. Eng l i s h Countries where you bought the unit ; # = ] Insert SD card Latin America Note This device supports Secure Digital High Capacity Russia, India Connect USB device (SDHC) card. 1 Detach the front panel.
4 Play/Pause Tap on the name to start play. Select audio track For video discs that contain two or more audio tracks. 1 To pause, tap . To resume play, tap 2 To skip forward/backward, tap 1 During play, tap anywhere except for the upper left corner to display the control bar. 2 Tap repeatedly to select audio track. » The audio channel information is displayed on upper line of the screen. again. Tip . You can also press DVD AUDIO on the remote control repeatedly to change audio track.
Tap to select: [Rep: chapter]: play the current chapter repeatedly. [Rep: title]: play all chapters in the title repeatedly. [Rep: disc]: cancel repeat play. For VCD karaoke: Tap to select: [Rep: one]: play the current track repeatedly. [Rep: disc]: cancel repeat play. Tap on the upper line of the screen to select: : play the current track repeatedly. : play all tracks in the current folder repeatedly. : cancel repeat play.
5 Listen to radio Zoom You can zoom in pictures for a close view. 1 During view pictures, tap anywhere except for the upper left corner to display the control bar. 2 Tap repeatedly to zoom in/out the picture. Rotate pictures 1 During view pictures, tap anywhere except for the upper left corner to display the control bar. 2 Tap Tune to a radio station 1 2 Tap to display home menu. Tap . » Band and frequency information is displayed. repeatedly to rotate the picture.
Tune to a preset station 1 2 Eng l i s h [Local]: stations with strong and weak signals can be broadcast. Select band. Tap one of the preset channels (1 to 6) to select a preset station. Store radio stations in memory You can store up to 6 stations in each band. Play with RDS (Optional) Store stations manually 1 2 3 Select band. Tune to the station by tapping or . Tap and hold one of the channels 1 to 6 over two seconds. » The station is saved under the selected channel.
Select program type Before tuning to RDS stations, you can select program type and let the unit search only for programs of the selected category. 1 Under radio mode, tap . » The radio option menu is displayed. 2 Tap [PTY list]. » The PTY list of available program type is displayed. 3 <= select an option. » The setting is changed.
1 2 Tap 3 Refer to the user manual of the navigation map to operate the navigation tool. to display main menu. Tap . » The navigation menu is displayed in a few seconds. Eng l i s h 6 Use navigation system Insert map card Note Navigation map card is not included in the packaging of the car entertainment system. 1 2 3 Press OPEN to release the panel. Open the card door under the screen. Insert the map card into the map card slot. GPS Card 4 5 Close the card door. Attach the front panel.
7 Play with Bluetooth device 6 Enter default password "0000" in your device. » iI the pairing succeeds. the phone call record is displayed. You can make or receive phone calls with Bluetooth-enabled phones through the unit. You can also listen to music from a Bluetoothenabled device. Pair the Bluetooth-enabled devices To connect your Bluetooth device to the unit, you need to pair the device to the unit. Pairing needs only to be done once. You can pair up to eight devices.
Tap on one device that you want to reconnect/disconnect. Tap (green) to reconnect the selected device. Tap (red) to disconnect the selected device. Tap Tap to clear all input. to go back to previous screen. 3 Tap 4 During talking, tap Eng l i s h 3 to start calling. Tip If the Bluetooth device is paired, under disconnect on top of the screen into the Bluetooth/ mode, tap paired device list.
Tip You can also press Tip / on front panel to answer/ You can enter desired name/number on the keypad to search quickly. terminate the call. Switch phone call to mobile phone If you do not want your passenger to hear your incoming call, you can switch the call the mobile phone. During talking, tap . » The voice is transferred from the loudspeaker to the mobile phone. Favorite call You can make a favorite call from the favorite call list. 1 Tap on top of screen. » The dial screen is displayed.
2 8 Play iPod/iPhone Eng l i s h [New Pairing]: pair the new device. [Paired Device]: display paired device. Tap an option to change the setting. Compatible iPod/iPhone Listen to music from Bluetooth device If the connected Bluetooth device supports ; ; & # ;~| you can listen to the music stored on the device through the unit.
1 Connect your iPod/iPhone to the front USB socket via Apple's own 30pin USB cable. » Music playback starts. 2 3 4 Tap ^ Tap on the screen to select desired song. Tap on the selected song to play. Charge the iPod/iPhone When the iPod/iPhone is connected to the car audio system, the iPod/iPhonebegins to charge. Tip For certain iPod models, it may take up to one minute before the charging indication is displayed. 2 3 4 5 To pause/resume play, tap . To skip a track, tap / .
3 Adjust EQ settings by tapping on the screen. [Bass] bass range: -14 to +14. [Middle] middle range: -14 to +14. [Treble] treble range: -14 to +14. [LPF] = _ 160. [MPF] " _ ] 1.0KHz, 1.5KHz, 2.5KHz. [HPF] _ ] 12.5KHz, 15.0KHz, 17.5KHz. 4 ? = sound settings, tap to restore default settings.
4 Tap . » The subwoofer setting is displayed. 4 Tap on the screen to adjust music listening zone setting. Turn FullSound on/off [Subwoofer]: tap [On]/[Off] on screen to turn the subwoofer on or off. Tap or to select subwoofer volume: 0 to 14. [LPF]: tap screen to select subwoofer = _ ~ 5 Tap to exit. Switch music listening zone Philips FullSound restores the audio details that is lost in music compression.
During play, tap on the upper line of screen. (red): turn maximizing sound (MAX sound) on. (gray): turn maximizing sound (MAX sound) off. 10 Adjust settings Eng l i s h Turn MAX sound on/off Display system setup menu 1 Tap 2 Tap . » The settings menu is displayed. > to display the full menu. Turn DBB on/off When DBB (Dynamic Bass Boost) is activated, low tones will be enhanced electronically. Tap on the upper line of screen to toggle between the settings.
General settings [Radio Region] Options [Beep] [On] [Off] [Language] [Calibration] [Clock Mode] [Date] [Time] [Parking] [12Hr]/[24Hr] [On] [Off] [Camera] [PAL/NTSC] [Demo] (Auto start after power off) [On] [Off] 4 Tap 34 EN Description Select one that matches your location. Turn the beep sound on. Each time you press a button, the unit beeps. Turn off the beep sound. Select OSD (on screen display) language. Calibrate the touch screen. Select time format. Set date. Set time. Turn parking on.
Options [On] [Off] [Navigation Voice Gain] [High] [Low] 3 Tap Description Access the Navigation Program Path mode. Turn the navigation voice on. Turn the navigation voice off. Select the navigation voice to high. Select the navigation voice to low. to exit. 2 Tap on a setting repeatedly to change setting. Bluetooth settings [New Pairing] [Auto Connect] Options [On] [On] [Off] Adjust Bluetooth settings 1 Tap [Pin Code] . [Device Name] 3 Tap Description Pair new device.
11 Others 1 In any mode, tap . » The option menu is displayed. 2 Tap [Display Design] to set the options. Adjust brightness 1 Press DISP on front panel repeatedly to adjust the dimmer settings. 2 Press and hold DISP to turn off the display, press again or tap on TFT screen to switch on. [Wallpaper]: tap to change wallpaper on screen. [Visualizer]: tap to change visualizer on screen. [Skin]: tap to change OSD display color. [Backlight]: tap to change main unit button illumination color.
Operate the connected the device (see instruction manual of the device). Tip If you connect the system to other audio devices Reset Eng l i s h 4 When the unit hangs up, you can reset it. Press RESET with a ball-point pen or similar tool. through the REAR OUT L/R connector (see "Wiring Diagram" section), tap [AV-IN2] to listen to that device. Detach the front panel You can detach the front panel to deter theft. 1 2 Press OPEN to release the panel. Push the right side of the panel leftward.
12 Product information Note Product information is subject to change without prior notice. FUSE (15A) General Power supply Tip If the fuse breaks immediately after it has been replaced, there may be an internal malfunction. In this case, consult your Philips dealer.
Radio Frequency range AM(MW) Usable sensitivity - FM Usable sensitivity - AM (MW) 87.5 - 108.0 MHz (50kHz per step) 522 - 1620 KHz (9kHz per step) 5 uV 25 uV LCD Screen size Display resolution Contrast ratio Brightness 7.0 inches 800 x 480 dots 500 450 cd/m2 Bluetooth Communication system Output Maximum communication range Frequency band Compatible Bluetooth Supported codecs Receive Transmit Bluetooth Standard version 2.0 Bluetooth Standard Power Class 2 Line of sight approx. 8m 2.
RealVideo3 (*.rm) RealVideo2 (*.ram) MS Video (*.avi) Note For format (container) not listed above, it is not guaranteed to work. Please avoid from using with the product. 13 Troubleshooting Warning Never remove the casing of this device. To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this device, check the following points before requesting service. If the problem remains unsolved, go to the Philips web site (www. philips.
Disc region code is not compatible with the unit. Use disc with proper region code. No image Parking wire connection is incorrect. Check the wiring. No image on rear display Check if you are playing DivX video. If yes, it’s normal, for this device does not support video out in DivX playing mode. Video DVD settings do not match with the DVD. Adjust video DVD settings. Video connection is improper. Check the connections. Noise in broadcasts. Signals are too weak.
Specifications are subject to change without notice © 2012 Koninklijke Philips Electronics N.V. All rights reserved. CED780_05_UM_V1.0 CED780_05_UM_V1.0.