Register your product and get support at www.philips.
3 1 2 3 H 4 5 6 8 10 7 9 11 12 13 14 I A B C J K L M G F D E 1
6 English introduction Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips. com/welcome. With this new bedroom air purifier you breathe cleaner air. For the best results, place the bedroom air purifier in a room where you spend most of your time, e.g. the bedroom. Wherever there are people, plants or pets, there are airborne particles that can affect your well-being, especially if you suffer from allergies.
English 7 8 SLEEP button with light 9 Power on/off button with light 10 FAN SPEED button with light 11 FAN SPEED lights (AC4004: 3 lights, AC4002: 2 lights) 12 RESET button for pre-filter 13 RESET button for filter 2 14 RESET button for filter 3/4 i Filter 4: HEPA filter (AC4124) J Filter 3: activated carbon filter (AC4123) K Filter 2 (AC4004 only): multi-care filter (AC4121) l Filter 1: pre-filter M Front panel important Read this user manual carefully before you use the appliance and save it for future
8 English - Do not place the appliance directly below an air conditioner to prevent condensation from dripping onto the appliance. Make sure all filters are properly installed before you switch on the appliance. Only use the original Philips filters specially intended for this appliance. Do not use any other filters. Avoid knocking against the appliance (the air inlet and outlet in particular) with hard objects. Always lift or move the appliance by the handgrip at the back of the appliance.
English 2 9 1 Place your fingers in the recesses of the side panels and gently pull the bottom of the front panel towards you. Then lift the hooks at the top of the panel out of the top of the appliance. 1 2 To remove the pre-filter, grab the two projections and pull the filter towards you. 3 Remove all other filters from the appliance. 4 Remove all packaging material from the filters. 5 Put filter 4 (HEPA filter) back into the appliance.
10 English 6 Put filter 3 (activated carbon filter) back into the appliance. 7 AC4004 only: attach filter 2 (multi-care filter) to the back of filter 1 (pre-filter). Note: Make sure that the front of filter 2 (multi-care filter), that is the side with the tag, points towards the pre-filter. 8 Place filter 1 (pre-filter) in the appliance. Note: AC4004: make sure the multi-care filter is attached to the back of the pre-filter. Note: Make sure that the side with the two projections points towards you.
English , The power-on light and one of the AIR QUALITY lights on the control panel goes on. English 11 11 The air quality light ring shows the quality of the air. AC4004: AiR QUAliTY lights Colour Air quality Blue very good Deep purple Purple Red Colour Blue Deep purple Purple Colour Red Blue good Air quality indication fair bad quality Air very good AC4002: AiR QUAliTY lights good fair Air quality bad very good Deep purple goodlight ring, press the AIR QUALITY button.
12 English Note:When the appliance is operating in another mode and you want to activate the auto mode, simply press the AUTO button. , The AUTO light and one of the FAN SPEED lights go on. The FAN SPEED light indicates at which fan speed the appliance is operating. Note:When the air quality is very good and the fan speed operates at a very low fan speed, the FAN SPEED light for the lowest speed level does not go on. In this case only the power-on light and the AUTO light are on.
English 13 - When you choose a fan speed manually (see section ‘Fan speed’ in this chapter). In this case, one of the FAN SPEED lights, the TIMER light and one of the HOUR lights are on. - In combination with the SLEEP mode (see section ‘Sleep mode’ in this chapter). In this case, the SLEEP light and one of the HOUR lights are on (but dimmed). 1 Press the on/off button to switch on the appliance. 2 Press the TIMER button to activate the timer. , The TIMER light goes on.
14 adjust the sensitivity of the air quality sensor. When it is set to a higher sensitivity level, the appliance already starts cleaning the air at lower pollution levels to make the air even cleaner. There are 3 sensitivity levels: - extra sensitive standard - sensitive - standard extra sensitive The air qualitysensor sensorisisset setto tostandard standardsensitivity. sensitivity.
English - 15 Clean the pre-filter when the filter cleaning light flashes to ensure optimal functioning of the appliance. 1 Unplug the appliance. 2 2 Place your fingers in the recesses of the side panels and gently pull the bottom of the front panel towards you. Then lift the hooks at the top of the panel out of the top of the appliance. 1 3 To remove the pre-filter, grab the two projections and pull the filter towards you. 4 AC4004 only: remove the multi-care filter from the back of the prefilter.
16 English 1 9 To reattach the front panel, insert the two hooks into the top of the appliance first (1). Then push the panel against the body of the appliance (2). 10 Put the plug in the wall socket. 2 11 Press and hold the reset button for filter 1 (the button below the filter cleaning light) for 2 seconds to reset the appliance. Air quality sensor Clean the air quality sensor every 2 months for optimal functioning of the appliance.
English 17 Filter replacement Filter maintenance When one of the filters is almost full and has to be cleaned or replaced, the corresponding light or lights (the pre-filter cleaning light or one of the filter replacement lights together with the ‘REPLACE FILTER’ light) start to flash. You then have to clean or replace this filter. This air purifier is also equipped with the Healthy air protect lock to ensure that the filters are in optimal condition when the appliance is operating.
If you do not replace the filter in time, the appliance stops operating approx. 2 weeks after the filter replacement light started flashing.When the appliance is locked, it does not operate until you have replaced the full filter and pressed the reset button. Note: time between the filter replacement signal and theFILTER lockingonofthe the Note:The When filter replacement lights 2 or 3/4 and REPLACE appliance varies, depending on how often you use the appliance.
English 19 5 To remove filter 3 (activated carbon filter), grab its tag and pull it towards you. 6 To remove filter 4 (HEPA filter), grab its tag and pull it towards you. 7 Discard the filter that has to be replaced and unpack the new filter. 8 Put filter 4 (HEPA filter) back into the appliance. Note: Make sure that the side with the tag points towards you. 9 Put filter 3 (activated carbon filter) back into the appliance.
20 English 11 Put filter 1 (pre-filter) back into the appliance. Note: Make sure that the side with the two projections points towards you. Note: Make sure that all hooks are properly attached to the appliance. 1 12 To reattach the front panel, insert the two hooks into the top of the appliance first (1). Then push the panel against the body of the appliance (2). 13 Put the plug in the wall socket and switch on the appliance again.
English 21 AC4002 only: adding the multi-care filter AC4002 comes with the pre-filter, activated carbon filter and the HEPA filter. For this appliance, only the filter cleaning light of filter 1 (pre-filter) and the filter replacement light of filter 3 and 4 (activated carbon filter and HEPA filter) have been activated. If you want to enjoy the benefits of the multi-care filter, you can purchase this filter separately (see the table above).
22 English Problem Possible solution The appliance doesn’t work. You ignored the filter replacement lights. You did not replace a filter when the corresponding filter replacement light and the REPLACE FILTER light started flashing and did not respond when the appliance started to beep every 30 minutes after approx. 2 weeks.
English Problem Possible solution The appliance still indicates that I need to replace a filter, but I already did. Perhaps you did not reset the appliance. Plug in the appliance, press and hold the reset button corresponding to the filter you have replaced. The appliance beeps if you have reset it properly. 23 When I press the SLEEP When you press the SLEEP button, the appliance enters the SLEEP mode, button, all lights except which is designed to allow you to sleep undisturbed.
© 2012 Koninklijke Philips Electronics N.V. All rights reserved.
