43BDL3510Q 50BDL3510Q 55BDL3510Q V1.00 www.philips.
43BDL3510Q_50BDL3510Q_55BDL3510Q Safety Instructions Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards. Read and follow these instructions when connecting and using your display: Operation: • Keep the display out of direct sunlight and away from stoves or any other heat sources.
43BDL3510Q_50BDL3510Q_55BDL3510Q • Only the lifetime of the display stated in this specification is guaranteed if the display is used under the proper operation conditions. IMPORTANT: Always activate a moving screen saver program when you leave your display unattended. Always activate a periodic screen refresh application if the unit will display unchanging static content.
3BDL3510Q_50BDL3510Q_55BDL3510Q Warning: This equipment is compliant with Class A of EN55032/CISPR 32. In a residential environment this equipment may cause radio interference. Federal Communications Commission (FCC) Notice (U.S. Only) NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
43BDL3510Q_50BDL3510Q_55BDL3510Q Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, display, printer, and so on) should have the same power supply source. The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A).
43BDL3510Q_50BDL3510Q_55BDL3510Q Information for U.K. only WARNING - THIS APPLIANCE MUST BE EARTHED. (B) Important: (A) This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows:+ 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place.
43BDL3510Q_50BDL3510Q_55BDL3510Q China RoHS 根据中国大陆《电器电子产品有害物质限制使用管理办法》，以下部分列出了本产品中可能包含的有害 物质的名称和含量。 有害物质 部件名称 铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr (VI)) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 外壳 O O O O O O 液晶显示屏 X O O O O O 电路板组件* X O O O O O 电源适配器 X O O O O O 电源线/连接线 X O O O O O 遥控器 X O O O O O 本表格依据SJ/T 11364 的规定编制。 *: 电路板组件包括印刷电路板及其构成的零部件，如电阻、电容、集成电路、连接器等。 O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572规定的限量要求以下。 X: 表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572规定的限量要求。 上表中打“X”的部件，应功能需要，部分有害物质含量超
43BDL3510Q_50BDL3510Q_55BDL3510Q 限用物質及其化學符號 單元 鉛 (Pb) 汞 (Hg) 鎘 (Cd) 六價鉻 (Cr+6) 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) 塑料外框 ○ ○ ○ ○ ○ ○ 後殼 ○ ○ ○ ○ ○ ○ 液晶面板 － ○ ○ ○ ○ ○ 電路板組件 － ○ ○ ○ ○ ○ 電源線 － ○ ○ ○ ○ ○ 其他線材 － ○ ○ ○ ○ ○ 遙控器 － ○ ○ ○ ○ ○ 喇叭（選配） － ○ ○ ○ ○ ○ 風扇（選配） － ○ ○ ○ ○ ○ 備考1.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。 備考2.
43BDL3510Q_50BDL3510Q_55BDL3510Q Waste Electrical and Electronic Equipment-WEEE Attention users in European Union private households This marking on the product or on its packaging illustrates that, under European Directive 2012/19/EU governing used electrical and electronic appliances, this product may not be disposed of with normal household waste. You are responsible for disposal of this equipment through a designated waste electrical and electronic equipment collection.
43BDL3510Q_50BDL3510Q_55BDL3510Q Batteries For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in accordance with legislation. Please contact your local authority for details on the collection and recycling schemes. For Switzerland: The used battery is to be returned to the selling point.
43BDL3510Q_50BDL3510Q_55BDL3510Q 5.2.4. 5.2.5. 5.2.6. 5.2.7. Table Of Contents 1. 2. Unpacking and Installation ........................................ 1 1.1. Unpacking ........................................................... 1 1.2. Package Contents ............................................. 1 1.3. Installation Notes.............................................. 1 1.4. Mounting on a Wall ......................................... 2 1.4.1. VESA Grid .............................................
43BDL3510Q_50BDL3510Q_55BDL3510Q 1. Unpacking and Installation 1.1. Unpacking • This product is packed in a carton, together with the standard accessories. • Any other optional accessories will be packed separately. • As this product is high and heavy, the operation of moving the device is recommended to be performed by two technicians. • After opening the carton, ensure that the contents are complete and in good condition. 1.2.
43BDL3510Q_50BDL3510Q_55BDL3510Q 1.4. Mounting on a Wall To mount this display on a wall, a standard wall-mounting kit (commercially available) is required. It is recommended that you use a mounting interface that complies with TUV-GS and /or UL1678 standard in North America. Protective Sheet VESA Grid Table 1. Spread a protective sheet which was wrapped around the display when it was packed on a flat surface.
43BDL3510Q_50BDL3510Q_55BDL3510Q 1.5. Mounting in Portrait Orientation This display can be installed in portrait orientation. Rotate the display 90 degrees Counterclockwise. The “ ” logo should be on the right side when facing the display. 90° 90° 1.5.1. How to remove the logo 1. Prepare a piece of paper with a cutting area of logo as a protector to prevent the front bezel from scratching. 1 2 3 2. Use a knife and carefully remove the logo sticker with the paper placing beneath. 3.
43BDL3510Q_50BDL3510Q_55BDL3510Q 2. Parts and Functions 2.1. Control Panel 9 1 1 2 3 4 5 6 7 8 [ ] button [MUTE] button 9 Press this button to mute the sound or reactivate sound. 3 [INPUT] button Choose the input source. 5 Receives command signals from the remote control.
43BDL3510Q_50BDL3510Q_55BDL3510Q 2.2. Input/Output Terminals 13 12 11 10 9 RJ45 USB 2.0 USB Service Port PC LINE IN AUDIO OUT IR-OUT IR-IN 1 1 2 HDMI 1 IN HDMI 2 IN DVI-I 3 4 5 11 AC IN AC power input from the wall outlet. 2 12 MAIN POWER SWITCH HDMI1 IN / 4 13 DVI IN RS232 IN / IR IN / 7 14 RS232 OUT 9 IR OUT NOTES: • This display’s remote control sensor will stop working if the jack [IR IN] is connected. 10 USB SERVICE PORT USB 2.
43BDL3510Q_50BDL3510Q_55BDL3510Q 2.3. Remote Control 1 [ ] POWER button Turn the display on or put the display to standby mode. 2.3.1. General functions 2 [PLAY] buttons Control playback of media files. 3 10 1 NORMAL [ ] SOURCE button Choose input source. Press [ ] or [ ] button to choose from VGA , DVI, HDMI 1, HDMI 2 or USB. Press [ ] button to confirm and exit. ID 11 4 2 [ ] HOME button Access the OSD menu. 5 FORMAT SOURCE 3 12 4 13 [ ] LIST button Reserved.
43BDL3510Q_50BDL3510Q_55BDL3510Q 2.3.2. ID Remote Control Press [ID] button. The red LED blinks twice. Set the remote control ID if you intend to use this remote control on several different displays. 1. Press [ID SET] button for more than 1 second to enter the ID Mode. The red LED lights up. Press the [ID SET] button again to exit from ID mode. The red LED lights off. Press the digit numbers [0] ~ [9] to select the display you want to control. For example: press [0] and [1] for display No.
43BDL3510Q_50BDL3510Q_55BDL3510Q 2.3.3. Inserting the batteries in the remote control The remote control is powered by two 1.5V AAA batteries. To install or replace batteries: 1. Press and then slide the cover to open it. 2. Insert batteries with the correct polarity (+) and (-). 3. Replace the cover. Caution: Incorrect use of batteries may cause leakage or explosion. Be sure to follow the instructions below: • Insert “AAA” batteries with the correct polarity (+ and -). • Do not mix battery types.
43BDL3510Q_50BDL3510Q_55BDL3510Q 2.4. USB Cover • Use the USB cover and screws to hide the USB stick.
43BDL3510Q_50BDL3510Q_55BDL3510Q 3. Connecting External Equipment 3.1. Connecting External Equipment (DVD/VCR/VCD) 3.1.1. Using HDMI video input HDMI 1 IN HDMI 2 IN [HDMI IN] HDMI Out DVD / VCR / VCD 3.2. Connecting a PC 3.2.1. Using DVI input PC [PC LINE IN] PC LINE IN DVI-I Audio Out [DVI IN] 3.2.2.
43BDL3510Q_50BDL3510Q_55BDL3510Q 3.3. Connecting Multiple Displays in a Daisy-chain Configuration You can interconnect multiple displays to create a daisy-chain configuration for applications such as a menu board. 3.3.1. Display control connection Connect the [RS232 OUT] connector of DISPLAY 1 to the [RS232 IN] connector of DISPLAY 2. DISPLAY 1 DISPLAY 2 PC [RS232] [RS232 IN] 3.4.
43BDL3510Q_50BDL3510Q_55BDL3510Q 3.6. Wire-connecting to Network INTERNET ROUTER [RJ-45] [RJ-45] PC Network Settings: 1. Switch the router on and enable its DHCP setting. 2. Connect the router to this display with an Ethernet cable. 3. Press [ ] HOME button on the remote control, then select Setup. 4. Select Connect to network, then press [ ] button. 5. Wait until this display finds the network connection. 6. If the “End User License Agreement” window prompts, accept the agreement.
43BDL3510Q_50BDL3510Q_55BDL3510Q 4. Operation 1/2 NOTE: The control button described in this section is mainly on the remote control unless specified otherwise. 4.1. Play multimedia files from USB device Return aaa1 aaa2 aaa3 xxx1 xxx2 xxx3 123 1. Connect your USB device to the USB port on the display. USB RJ45 USB 2.0 USB Service Port PC LINE IN AUDIO OUT IR-OUT IR-IN 8. Press [ ], [ ], [ ] or [ ] button to choose “Return" item ] button to return to the top layer. then press [ 2.
43BDL3510Q_50BDL3510Q_55BDL3510Q 5. 5.2. OSD Menu An overview of the On-Screen Display (OSD) structure is shown below. You can use it as a reference for further adjustment of your display. 5.1. 5.2.1. Picture menu Navigating the OSD Menu 5.1.1.
43BDL3510Q_50BDL3510Q_55BDL3510Q Press - button to narrow the width of the image on the screen to the left. Color temperature It is used to adjust the color temperature. NOTE: VGA input only. The image becomes reddish as the color temperature decreases, and becomes bluish as the color temperature increases. Clock Phase Scan mode Improves focus, clarity and image stability by increasing or decreasing this setting. Change the display area of the image. NOTE: VGA input only.
43BDL3510Q_50BDL3510Q_55BDL3510Q V position Off : Disable the function and gray out Audio Out Volume. Moves the vertical position of the image up or down. Source Select the audio input source. Analog: audio from audio input. Auto adjust Digital : audio from HDMI/DVI audio. Press “Set” to detect and adjust H position, V position, Clock, Phase automatically. Audio reset Reset all settings in the Audio menu to factory preset values. NOTE: VGA input only. Screen reset 5.2.4.
43BDL3510Q_50BDL3510Q_55BDL3510Q {Off} Example: 2 x 2 screen matrix (4 displays) H monitors = 2 displays V monitors = 2 displays V monitors H monitors 1 2 3 4 Position Example: 5 x 5 screen matrix (25 displays) H monitors = 5 displays V monitors = 5 displays Frame comp. Top Adjust the top frame compensation. Frame comp. Bottom Adjust the bottom frame compensation. V monitors H monitors 1 6 11 16 21 2 7 12 17 22 3 8 13 18 23 4 9 14 19 24 5 10 15 20 25 Position Frame comp.
43BDL3510Q_50BDL3510Q_55BDL3510Q Monitor ID 5.2.6. Configuration menu Set the ID number for controlling the display via the RS232 connection. Each display must have a unique ID number when multiple sets of display are connected. Monitor ID number range is between 1 to 255. PICTURE Switch on State SCREEN Network Control Port AUDIO Boot on source Last input TILING Power LED light On NETWORK OSD Turn Off 15 • {1-255} – {Monitor ID} The default setting is 1.
43BDL3510Q_50BDL3510Q_55BDL3510Q 5.2.7. Option PICTURE Language SCREEN Auto signal detection AUDIO Date and Time TILING Schedule NETWORK HDMI EDID 2.
43BDL3510Q_50BDL3510Q_55BDL3510Q Leave hour and minute options empty if you do not want to use the function of power-on or power-off schedule. • Keypad Control Choose to enable or disable the display keyboard (control buttons) function. {Repeat modes} -Press [ ] button to select which day in a week this schedule item will take effect, and then press the [OK] button. ], then repeat 3. For additional schedule settings, press [ the steps above.
43BDL3510Q_50BDL3510Q_55BDL3510Q Slideshow Duration Duration of each picture for USB autoplay and USB Play List. USB Play List Choose 1 playlist to play, support up to 7 playlists. USB Cloning Copy PD settings from one set to another. Import: Import settings from another set. Export: Export settings to another set. Firmewre update Update firmware via USB disk. Factory Reset Reset all your customized settings to the factory default values.
43BDL3510Q_50BDL3510Q_55BDL3510Q 6. Supported Media Formats USB Multimedia Formats Video format Video Codec Resolution Bit Rate MPEG1/2 1080P@30fps 40Mbps H.264 1080P@30fps 50Mbps WMV3 1080P@30fps 40Mbps Motion JPEG 640x480@30fps 40Mbps Audio format Audio Codec Sampling Rate Channel Bit Rate MPEG1/2 Layer1 16KHz-48KHz Up to 2 32Kbps-448Kbps MPEG1/2 Layer2 16KHz-48KHz Up to 2 8Kbps-384Kbps MPEG1/2 Layer3 16KHz-48KHz Up to 2 8Kbps-320Kbps AAC, HEAAC 8KHz-48KHz Up to 5.
43BDL3510Q_50BDL3510Q_55BDL3510Q 7. Input Mode Timing support: • • • • • • • • Item Resolution H.Freq. (KHz) V.Freq. (Hz) 1 720×400 @70Hz DOS 31.469 70.087 2 640×480 @60Hz DMT 31.469 59.94 3 640×480 @67Hz MAC 35 66.667 4 640×480 @72Hz DMT 37.861 72.809 5 640×480 @75Hz DMT 37.5 75 6 800×600 @56Hz DMT 35.156 56.25 7 800×600 @60Hz DMT 37.879 60.317 8 800×600 @72Hz DMT 48.077 72.188 9 800×600 @75Hz DMT 46.875 75 10 832×624 @75Hz MAC 49.725 74.
43BDL3510Q_50BDL3510Q_55BDL3510Q 8. Pixel Defect Policy We strive to deliver the highest quality products and use some of the industry’s most advanced manufacturing processes whilst practicing stringent quality control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCDdisplays are sometimes unavoidable.
43BDL3510Q_50BDL3510Q_55BDL3510Q 8.4. Dark Dot Defects Black dot defects appear as pixels or sub-pixels that are always dark or “off”. These are the examples of black dot defects: One dark dot 8.5.
43BDL3510Q_50BDL3510Q_55BDL3510Q HOW TO AVOID MURA Although we can not guarantee the complete eradication of Mura every time, in general the appearance of Mura can be minimized by these methods: • Lower the backlight brightness • Use a screen saver • Reduce the ambient temperature around the unit 9. Cleaning and Troubleshooting 9.1. Cleaning Caution When Using the Display • Do not bring your hands, face or objects close to the ventilation holes of the display.
43BDL3510Q_50BDL3510Q_55BDL3510Q 9.2. Troubleshooting Symptom Possible Cause Remedy No picture is displayed 1. The power cord is disconnected. 1. Plug in the power cord. 2. The main power switch on the back of the display is not switched on. 2. Make sure the power switch is switched on. 3. The selected input has no connection. 3. Connect a signal connection to the display. 4. The display is in standby mode.
43BDL3510Q_50BDL3510Q_55BDL3510Q 10. Technical Specifications Display: Item Specifications 43BDL3510Q 50BDL3510Q 55BDL3510Q Screen Size (Active Area) 108 cm / 42.5 inch 125.7 cm / 49.5 inch 138.7 cm / 54.6 inch Aspect Ratio 16:9 16:9 16:9 Number of pixels 3840 (H) x 2160 (V) 3840 (H) x 2160 (V) 3840 (H) x 2160 (V) Pixel pitch 0.315 (H) x 0.315 (V) [mm] 0.372 (H) x 0.372 (V) [mm] 0.372 (H) x 0.372 (V) [mm] Displayable colors 8 bits+FRC, 1.07 Billion colors 8 bits+FRC, 1.
43BDL3510Q_50BDL3510Q_55BDL3510Q General: Item Specifications 43BDL3510Q 50BDL3510Q 55BDL3510Q Power Input 100 - 240V~, 50/60Hz 100 - 240V~, 50/60Hz 100 - 240V~, 50/60Hz Power Consumption (Max) 150 W 165 W 180 W Power Consumption (typ.) 90 W 105 W 120 W Power Consumption (Standby & Off) <0.5 W <0.5 W <0.5 W Dimensions [W x H x D] 973.0 x 561.2 x 63.5 mm 1128.4 x 649.0 x 63.5 mm 1241.8 x 712.6 x 63.6 mm Weight 11.3 Kg 14.8 Kg 16.6 Kg Gross Weight 14.7 Kg 18.6 Kg 22.
2020 © Koninklijke Philips N.V. All rights reserved. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license from Koninklijke Philips N.V. Specifications are subject to change without notice.
