Specifications

ManualsBrandsPhilips ManualsPrint & Scan56PFL9954H/98

Published by JA/EL 0968 BU TV Consumer Care, the Netherlands Subject to modification EN 3122 785 18312

2009-Aug-14

retrieval system or transmitted, in any form or by any means, electronic, mechanical,

photocopying, or otherwise without the prior permission of Philips.

Colour Television Chassis

Q549.2E

18310_000_090317.eps

090317

Contents Page Contents Page

1. Revision List 2

2. Technical Specifications and, Connections 2

3. Precautions, Notes, and Abbreviation List 6

4. Mechanical Instructions 10

5. Service Modes, Error Codes, and Fault Finding 15

6. Alignments 36

7. Circuit Descriptions 42

8. IC Data Sheets 53

9. Block Diagrams

Wiring Diagram 32" (Elite Core) 59

Wiring Diagram 37" (Elite Core) 60

Block Diagram Video 62

Block Diagram Audio 63

Block Diagram Control & Clock Signals 64

Block Diagram I2C 65

Supply Lines Overview 66

10. Circuit Diagrams and PWB Layouts Drawing PWB

Ambilight Interface: Interf. + Single DC-DC

(AB1)67 70

Ambilight Interface: Dual DC-DC (AB2) 68 70

Ambilight Interface: Microcontroller (AB3) 69 70

6 LED: Microcontroller Block (AL1) 71 74

6 LED: Microcontroller Block (AL2) 72 74

6 LED: LED Block (AL3) 73 74

8 LED: Microcontroller Block (AL1) 75 79

8 LED: Microcontroller Block (AL2) 76 79

8 LED: LED Block (AL3) 77 79

8 LED: LED Drive Block (AL4) 78 79

10 LED: Microcontroller Block (AL1) 80 84

10 LED: Microcontroller Block (AL2) 81 84

10 LED: LED Block (AL3) 82 84

10 LED: LED Drive Block (AL4) 83 84

SSB (B01A-B10) 85-133 137-138

SSB: SRP List Explanation 134

SSB: SRP List Part 1 135

SSB: SRP List Part 2 136

Light guide 139 140

Wi-Fi Antenna 141 141

Summary of content (141 pages)

PAGE 1
Colour Television Chassis Q549.2E LA 18310_000_090317.
PAGE 2
EN 2 1. Q549.2E LA Revision List 1. Revision List Manual xxxx xxx xxxx.1 • All Chapters: Added 56PFL9954H/98 to the manual. • All Chapters: Minor textual improvements. Manual xxxx xxx xxxx.0 • First release. Manual xxxx xxx xxxx.1 • All Chapters: the following sets to the manual: see Table 2-1 Described Model numbers. • Chapter 5: paragraph 5.8.10 PCI bus added. • Chapter 6: paragraph 6.6 Service SSB delivered without main software loaded added. 2.
PAGE 3
Technical Specifications and, Connections 2.3 Q549.2E LA 2. EN 3 Connections SERVICE UART VGA AUDIO IN VGA NETWORK 4 3 2 1 18310_001_090317.
PAGE 4
EN 4 2. Q549.2E LA Technical Specifications and, Connections Note: The following connector colour abbreviations are used (acc. to DIN/IEC 757): Bk= Black, Bu= Blue, Gn= Green, Gy= Grey, Rd= Red, Wh= White, Ye= Yellow. 2.3.1 Side Connections Head phone (Output) Bk - Head phone 32 - 600 ohm / 10 mW Cinch: Video CVBS - In, Audio - In Rd - Audio R 0.5 VRMS / 10 kohm Wh - Audio L 0.
PAGE 5
Technical Specifications and, Connections Cinch: Audio - In (VGA/DVI) Rd - Audio R 0.5 VRMS / 10 kohm Wh - Audio L 0.5 VRMS / 10 kohm Q549.2E LA 2. EN 5 jq jq HDMI 1, 2, 3 & 4: Digital Video, Digital Audio - In 19 18 1 2 E_06532_017.eps 250505 Figure 2-6 HDMI (type A) connector 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 2.4 - D2+ - Shield - D2- D1+ - Shield - D1- D0+ - Shield - D0- CLK+ - Shield - CLK- Easylink/CEC - n.c.
PAGE 6
EN 6 3. Q549.2E LA Precautions, Notes, and Abbreviation List 3. Precautions, Notes, and Abbreviation List Index of this chapter: 3.1 Safety Instructions 3.2 Warnings 3.3 Notes 3.4 Abbreviation List 3.1 Safety Instructions Safety regulations require the following during a repair: • Connect the set to the Mains/AC Power via an isolation transformer (> 800 VA). • Replace safety components, indicated by the symbol h, only by components identical to the original ones.
PAGE 7
Precautions, Notes, and Abbreviation List 3.3.6 3.4 Alternative BOM identification It should be noted that on the European Service website, “Alternative BOM” is referred to as “Design variant”. The third digit in the serial number (example: AG2B0335000001) indicates the number of the alternative B.O.M. (Bill Of Materials) that has been used for producing the specific TV set. In general, it is possible that the same TV model on the market is produced with e.g.
PAGE 8
EN 8 3. DNR DRAM DRM DSP DST DTCP DVB-C DVB-T DVD DVI(-d) E-DDC EDID EEPROM EMI EPLD EU EXT FDS FDW FLASH FM FPGA FTV Gb/s G-TXT H HD HDD HDCP HDMI HP I I2 C I2 D I2 S IF IR IRQ ITU-656 2009-Aug-14 Q549.
PAGE 9
Precautions, Notes, and Abbreviation List PWM QRC QTNR QVCP RAM RGB RC RC5 / RC6 RESET ROM RSDS R-TXT SAM S/C SCART SCL SCL-F SD SDA SDA-F SDI SDRAM SECAM SIF SMPS SoC SOG SOPS SPI S/PDIF SRAM SRP SSB STBY SVGA SVHS SW SWAN SXGA TFT THD TMDS TXT TXT-DW UI uP UXGA V VESA VGA VL VSB WYSIWYR WXGA XTAL XGA Pulse Width Modulation Quasi Resonant Converter Quality Temporal Noise Reduction Quality Video Composition Processor Random Access Memory Red, Green, and Blue. The primary color signals for TV.
PAGE 10
EN 10 4. Q549.2E LA Mechanical Instructions 4. Mechanical Instructions Index of this chapter: 4.1 Cable Dressing and Taping 4.2 Service Positions 4.3 Assy/Panel Removal 4.4 Set Re-assembly 4.1 Notes: • Figures below can deviate slightly from the actual situation, due to the different set executions. Cable Dressing and Taping 18310_210_090318.
PAGE 11
Mechanical Instructions Q549.2E LA 4. EN 11 18310_211_090318.eps 090318 Figure 4-2 Cable dressing 37" 18311_200_090506.
PAGE 12
EN 12 4.2 4. Q549.2E LA Mechanical Instructions Service Positions 4.3.3 Each Ambilight unit is mounted on a subframe. Refer to Figure 4-5 for details. For easy servicing of this set, there are a few possibilities created: • The buffers from the packaging. • Foam bars (created for Service). 4.2.1 Ambilight Foam Bars 1 1 1 Required for sets 42" E_06532_018.eps 171106 18310_212_090318.
PAGE 13
Mechanical Instructions Q549.2E LA 4. EN 13 1. Remove the Main Supply Panel as earlier described. 2. Remove the stand [1] and its subframe [2]. 3. Now you gain access the IR & LED board. When defective, replace the whole unit. 4.3.6 Piezo Touch Control Panel 4 The flexfoil between Piezo Flexfoil Assy (mounted on the plastic rim of the set), and the PWB as described below, is extremely vulnerable. Do not pull hard at the PWB or flexfoil.
PAGE 14
EN 14 4. Q549.2E LA 4 1 Mechanical Instructions 1 18310_217_090318.eps 090320 Figure 4-10 LCD Panel -1- 2 3 18310_218_090318.eps 090319 Figure 4-11 LCD Panel -24.3.9 Wi-Fi antenna Follow the instructions for LCD Panel until “remove plastic rim”. After removal of this rim, you gain access to the Wi-Fi antennas. 4.4 Set Re-assembly To re-assemble the whole set, execute all processes in reverse order.
PAGE 15
Service Modes, Error Codes, and Fault Finding Q549.2E LA 5. EN 15 5. Service Modes, Error Codes, and Fault Finding • Index of this chapter: 5.1 Test Points 5.2 Service Modes 5.3 Stepwise Start-up 5.4 Service Tools 5.5 Error Codes 5.6 The Blinking LED Procedure 5.7 Protections 5.8 Fault Finding and Repair Tips 5.9 Software Upgrading 5.1 How to Activate SDM For this chassis there are two kinds of SDM: an analogue SDM and a digital SDM. Tuning will happen according Table 5-1.
PAGE 16
EN 16 • • 5. Q549.2E LA Service Modes, Error Codes, and Fault Finding To view operation hours. To display (or clear) the error code buffer. TV will go to the Stand-by mode. If the NVM was corrupted or empty before this action, it will be initialized first (loaded with default values). This initializing can take up to 20 seconds. How to Activate SAM Via a standard RC transmitter: Key in the code “062596” directly followed by the “INFO” button.
PAGE 17
Service Modes, Error Codes, and Fault Finding • With the “OK” key, it is possible to activate the selected action. How to Exit SAM Use one of the following methods: • Switch the TV set to STAND-BY via the RC-transmitter. • Via a standard RC-transmitter, key in “00” sequence, or select the “BACK” key. 5.2.3 Customer Service Mode (CSM) Purpose When a customer is having problems with his TV-set, he can call his dealer or the Customer Helpdesk.
PAGE 18
EN 18 5.3 5. Q549.2E LA Service Modes, Error Codes, and Fault Finding Stepwise Start-up mode with a faulty FET 7U08 is done, you can destroy all IC’s supplied by the +3V3, due to overvoltage (12V on 3V3-line). It is recommended to measure first the FET 7U08 or others FET’s on shortcircuit before activating SDM via the service pads.
PAGE 19
Service Modes, Error Codes, and Fault Finding Q549.2E LA 5. EN 19 Off Stand by or Protection Mains is applied Standby Supply starts running. All standby supply voltages become available .
PAGE 20
EN 20 5. Service Modes, Error Codes, and Fault Finding Q549.2E LA From I_17660_125a.eps From I_17660_125a.eps Reset-system is switched HIGH by the AVC at the end of the bootscript Reset-system is switched HIGH by the AVC at the end of the bootscript Release reset MPEG4 module: BOLT-ON-IO: High AVC releases Reset-Ethernet when the end of the AVC boot-script is detected AVC releases Reset-Ethernet when the end of the AVC boot-script is detected MPEG4 module will start booting autonomously.
PAGE 21
Service Modes, Error Codes, and Fault Finding Q549.2E LA 5. EN 21 Constraints taken into account: - Display may only be started when valid LVDS output clock can be delivered by the AVC . - Between 5 and 50 ms after power is supplied, display should receive valid lvds clock . - minimum wait time to switch on the lamp after power up is 200ms. action holder: AVC action holder: St-by autonomous action Semi Standby The assumption here is that a fast toggle (<2s) can only happen during ON -> SEMI -> ON.
PAGE 22
EN 22 5. Service Modes, Error Codes, and Fault Finding Q549.2E LA Constraints taken into account: - Display may only be started when valid LVDS output clock can be delivered by the AVC . - Between 5 and 50 ms after power is supplied, display should receive valid lvds clock . - minimum wait time to switch on the lamp after power up is 200ms. - To have a reliable operation of the backlight, the backlight should be driven with a PWM duty cycle of 100% during the first second.
PAGE 23
Service Modes, Error Codes, and Fault Finding Q549.2E LA 5. EN 23 action holder: AVC Constraints taken into account: - Display may only be started when valid LVDS output clock can be delivered by the AVC . - Between 5 and 50 ms after power is supplied, display should receive valid lvds clock . - minimum wait time to switch on the lamp after power up is 200ms. action holder : St-by autonomous action Semi Standby The assumption here is that a fast toggle (<2s) can only happen during ON -> SEMI -> ON.
PAGE 24
EN 24 5. Q549.
PAGE 25
Service Modes, Error Codes, and Fault Finding Q549.2E LA Semi Stand by 5. EN 25 action holder: MIPS action holder: St-by autonomous action If ambientlight functionality was used in semi -standby (lampadaire mode), switch off ambient light Delay transition until ramping down of ambient light is finished. *) *) If this is not performed and the set is switched to standby when the switch off of the ambilights is still ongoing , the lights will switch off abruptly when the supply is cut.
PAGE 26
EN 26 5. Q549.2E LA action holder: MIPS Service Modes, Error Codes, and Fault Finding MP SP action holder: St-by autonomous action Log the appropriate error and set stand-by flag in NVM Redefine wake up reasons for protection state and transfer to stand-by µP. Switch off LCD lamp supply If needed to speed up this transition, this block could be omitted . This is depending on the outcome of the safety investigations . Wait 250ms (min.
PAGE 27
Service Modes, Error Codes, and Fault Finding 5.4 Service Tools 5.4.1 ComPair 5.4.2 5. EN 27 Memory and Audio Test With this tool you can test the memory of the PNX8543, as well if the PNX5100 is enabled and audio-testing. Introduction ComPair (Computer Aided Repair) is a Service tool for Philips Consumer Electronics products. and offers the following: 1. ComPair helps to quickly get an understanding on how to repair the chassis in a short and effective way. 2.
PAGE 28
EN 28 • • • • 5. Q549.2E LA Service Modes, Error Codes, and Fault Finding For all errors detected by MIPS which are fatal => rebooting of the TV set (reboot starts after LAYER 1 error blinking), one should short the solder paths (SDM) at start-up from the power OFF state by mains interruption and not via the power button to trigger the SDM via the hardware pins. In CSM mode – When entering CSM: error LAYER 1 will be displayed by blinking LED. Only the latest error is shown.
PAGE 29
Service Modes, Error Codes, and Fault Finding Q549.2E LA 5.
PAGE 30
EN 30 • • • • • 5. Q549.2E LA Service Modes, Error Codes, and Fault Finding Error 34 (Tuner). When there is no I2C communication towards the tuner after start-up, LAYER 2 error = 34 will be logged and displayed via the blinking LED procedure when SDM is switched on. Error 42 (Temp sensor). Only applicable for TV sets with an I2C controlled screen. Main NVM. When there is no I2C communication towards the main NVM, LAYER 1 error = 2 will be displayed via the blinking LED procedure.
PAGE 31
Service Modes, Error Codes, and Fault Finding 5.7.2 Hardware Protections • The only real hardware protection in this chassis appears in case of an audio problem e.g. DC voltage on the speakers. This protection will only affect the Class D (7D10) and puts the amplifier in a continuous burst mode (cyclus approximately 2 seconds). The linear stabilizers are providing: • • • • Repair Tip • There will be still picture available but no sound.
PAGE 32
EN 32 5.8.6 5. Q549.2E LA Service Modes, Error Codes, and Fault Finding Logging When something is wrong with the TV set (f.i.the set is rebooting) you can check for more information via the logging in Hyperterminal. The Hyperterminal is available in every Windows application via Programs, Accessories, Communications, Hyperterminal. Connect a “ComPair UART”cable (3138 188 75051) from the service connector in the TV to the “multi function” jack at the front of ComPair II box.
PAGE 33
Service Modes, Error Codes, and Fault Finding 5.8.15 SSB Replacement Q549.2E LA 5. EN 33 Attention: Flowchart 5.14 below is only valid when the new SSB already contains the main TV software. When this is not the case, refer to 6.6 Service SSB delivered without main software loaded for more information. Follow the instructions in the flowchart in case a SSB has to be exchanged. See figure 5-14 SSB replacement flowchart. Instruction note: SSB replacement Q528.x, Q522.x, Q529.x, Q54x.
PAGE 34
EN 34 5. Q549.2E LA 5.9 Software Upgrading 5.9.1 Introduction Service Modes, Error Codes, and Fault Finding 4. Insert USB stick into the TV. 5. The renamed “upg” file will be visible and selectable in the upgrade application. Back-up Software Upgrade Application If the default software upgrade application does not start (could be due to a corrupted boot 2 sector) via the above described method, try activating the “back-up software upgrade application”.
PAGE 35
Service Modes, Error Codes, and Fault Finding Q549.2E LA 5. EN 35 – • • • • • • • 5.9.5 Content of the MOP Ambilight ARM SW File • 5.9.6 The “StandbySW_xxxxx.hex” file can be used to upgrade the Stand-by software via ComPair. – The files “StandbySW_xxxxx_exhex.hex” and “StandbySW_xxxxx_dev.upg” may not be used by Service technicians (only for development purposes). UpgradeAll_Q5492_x.x.x.x_commercial.zip. Only for production purposes, not to be used by Service technicians.
PAGE 36
EN 36 6. Q549.2E LA Alignments 6. Alignments • Index of this chapter: 6.1 General Alignment Conditions 6.2 Hardware Alignments 6.3 Software Alignments 6.4 Option Settings 6.5 Reset of Repaired SSB 6.7 Total Overview SAM modes 6.1 General Alignment Conditions Perform all electrical adjustments under the following conditions: • Power supply voltage (depends on region): – AP-NTSC: 120 VAC or 230 VAC / 50 Hz (± 10%). – AP-PAL-multi: 120 - 230 VAC / 50 Hz (± 10%). – EU: 230 VAC / 50 Hz (± 10%).
PAGE 37
Alignments • • • Table 6-2 White tone default setting Colour Temp 32" R G 37" Black level offset B R G B R G 8 Normal 127 95 97 127 121 106 8 Cool 127 100 112 124 127 119 8 8 Warm 127 89 52 127 111 64 8 8 White Tone Colour Temp 56" R G B R G 127 117 111 8 8 Cool 124 124 125 8 8 Warm 127 95 65 8 8 EN 37 Diversity Not all sets with the same Commercial Type Number (CTN) necessarily have the same option code! Use of Alternative BOM => an alternative
PAGE 38
EN 38 6.5.1 6. Q549.2E LA Alignments SSB identification 3. Create a folder "upgrades" in the root of a USB stick (size > 50 MB) and save the "autorun.upg" file in this "upgrades" folder. Note: it is possible to rename this file, e.g. "Q549_SW_version.upg", this in case there are more than one "autorun.upg" files on your USB stick 4. Plug the prepared USB stick into the TV set, and select the "autorun" file in the displayed browser on the screen 5.
PAGE 39
Alignments Q549.2E LA EN 39 Main Menu Sub-menu 1 Sub-menu 2 Dealer options Picture mute Off/On Select Picture mute On/Off. Picture is muted / not muted in case no input signal is detected at input connectors. Virgin mode Off/On Select Virgin mode On/Off. TV starts up / does not start up (once) with a language selection menu after the mains switch is turned “on” for the first time (virgin mode) Select E-sticker On/Off (Uses on-screen) E-sticker Off/On Auto store mode None Sub-menu 3 6.
PAGE 40
EN 40 6. Main Menu Q549.2E LA Alignments Sub-menu 1 Sub-menu 2 Audio reproduction Acoustic system Source selection EXT1/AV1 type Sub-menu 3 Description Cabinet design used for setting dynamic audio parameters. SCART CVBS RGB LR Select input source when connected with external equipment. CVBS Y/C YPbPr LR CVBS Y/C YPbPr HV LR (CVBS) YPbPr LR EXT2/AV2 type SCART CVBS RGB LR Select input source when connected with external equipment.
PAGE 41
Alignments Main Menu Sub-menu 1 Development file ver- Development 1 file version sions Sub-menu 2 Display parameters DISPT 3.26.8.7 Sub-menu 3 Q549.2E LA 6. EN 41 Description Display information is for development purposes. Acoustics parameters ACSTS 3.6.6.5 PQ - PRFPP 1.26.10.4 Ambilight parameters PRFAM 2.6.1.3 Development 2 file version 12NC one zip software Display information is for development purposes. Initial main software NVM version Q5492_0.4.0.0 Flash units SW Q5492_0.26.15.
PAGE 42
EN 42 7. Circuit Descriptions Q549.2E LA 7. Circuit Descriptions Main difference with the previous platform is the introduction of “Net TV” and “CI+”. Index of this chapter: 7.1 Introduction 7.2 Power Architecture 7.3 Front-End 7.4 HDMI 7.5 Video and Audio Processing - PNX8543 7.6 Common Interface CI+ 7.7 Net TV 7.8 Ambi Light 7.1.
PAGE 43
Circuit Descriptions 7. EN 43 SSB Cell Layout 1CJ0 1M01 1R12 serv DDR2 DDR2 lvds-rx CY3 C40 ambi 5100 40x40 1.
PAGE 44
EN 44 7.2 7. Circuit Descriptions Q549.2E LA Power Architecture Refer to figure Figure 7-3 for the power architecture of this platform. F use PSU P la tfo rm P ow er 12VD isp V display LC D Power-on SSB Standby 3V3stby PNX5100 +3V3 stby +1V2 BL D IM * +1V2-ST AN D BY Lam p On * BL D IM Lam p On F use Fuse +12V 12V U ndervoltage detect Enable-3V3 +1V2 +1V2-PNX85XX +3V3 +3V3 D ual D C/D C Sw itches off +3V3 and +5V Inverter** Display +3V3F +2V5 +2V5 +2V5 (loc.Contr.
PAGE 45
Circuit Descriptions 7.3 Q549.2E LA 7. EN 45 Front-End P la tfo rm w ith e m b e d d e d E D ID The Front-End consist of the following key components: • • • • Tuner HD1816AF SAW filter 36M125 IF demodulator DRX3926K AGC amplifier UPC3221GV. E D ID: 2 5 3 B 3B 3B 3B I2C-SSB 4 × HDMI inputs CVBS SAW Filter IF Amplifier DRX3926K 2nd SIF PNX8543 TS 18440_211_090227.
PAGE 46
EN 46 7. Q549.2E LA Circuit Descriptions PNX8543x MEMORY CONTROLLER TS in from channel decoder MPEG SYSTEM PROCESSOR CI/CA TS out/in for PCMCIA DV-ITU-656 PRIMARY VIDEO OUTPUT LVDS for flat panel display (single or dual channel) LVDS DV INPUT AV-PIP SUB-PICTURE VIDEO DECODER CVBS, Y/C, RGB 3D COMB SECONDARY VIDEO OUTPUT Low-IF SSIF, LR DIGITAL IF MPEG/H.
PAGE 47
Circuit Descriptions Q549.2E LA 7.
PAGE 48
EN 48 7. Circuit Descriptions Q549.
PAGE 49
Circuit Descriptions Q549.2E LA 7. EN 49 DDR2-SDRAM PNX8543x MCU_DDR IIC4_DMA I2C-2 IIC2_DMA UART-1 IIC3_DMA UART1 DMA BUS I2C-3 MIPS 4KEc DCS-NETWORK I2C-1 EJTAG AVDSP PCI_XIO PCI/XIO UART-2 UART2 CAI USB CI/CA USB2.0 I2C-MC EJTAG JTAG_MMIO SYSTEM CONTROLLER 80C51 UART-3 PWMs GPIOs 18440_205_090226.eps 090226 Figure 7-10 PNX8543 connectivity and compute subsystem The Connectivity Subsystem consists of: • PCI/XIO interface • USB2.
PAGE 50
EN 50 7.6 7. Circuit Descriptions Q549.2E LA Common Interface CI+ Access Module (CAM) and the Integrated Digital Television (IDTV). The security mechanisms in CI+ are derived/copied from POD (with the exception of Out Of Band (OOB) used in US CA systems). For more information about conventional CA systems using a CI module, refer to the BJ3.0E L/PA or BL2.xU Service Manual. Together with this platform, an extention to the Common Interface (CI) Conditional Access system is added, called CI+.
PAGE 51
Circuit Descriptions Q549.2E LA 7. EN 51 18310_203_090317.eps 090317 Figure 7-12 Interface between Ambilight and SSB The SPI bus is a synchronous serial data link standard that operates in full duplex mode. ARM controller Refer to Figure 7-13 below for signal interfacing to and from the ARM controller. The ARM controller is located on the DC/DC board (item no. 7302) or AL panel (item no. 7102). SD A SC L S E L1 S E L2 S da1 Sck S c l1 P 0. 7 t bd P 0. 8 M OSI M A T0.0 AR M M ISO M A T1.
PAGE 52
EN 52 7. Q549.2E LA Circuit Descriptions Figure 7-14 SPI communication between ARM controller and LED drivers The ARM controller communicates with the LED drivers (on each AL module) via an SPI bus.
PAGE 53
IC Data Sheets Q549.2E LA 8. EN 53 8. IC Data Sheets This chapter shows the internal block diagrams and pin configurations of ICs that are drawn as “black boxes” in the 8.1 electrical diagrams (with the exception of “memory” and “logic” ICs).
PAGE 54
EN 54 8.2 8. IC Data Sheets Q549.
PAGE 55
IC Data Sheets 8.3 Q549.2E LA 8. EN 55 Diagram SSB: PNX8543 - Stand-by Controller B04A, PNX8543 (IC7H00) Block Diagram PNX8543x MEMORY CONTROLLER TS in from channel decoder MPEG SYSTEM PROCESSOR CI/CA TS out/in for PCMCIA DV-ITU-656 PRIMARY VIDEO OUTPUT LVDS for flat panel display (single or dual channel) LVDS DV INPUT AV-PIP SUB-PICTURE VIDEO DECODER CVBS, Y/C, RGB 3D COMB SECONDARY VIDEO OUTPUT Low-IF SSIF, LR DIGITAL IF MPEG/H.
PAGE 56
EN 56 8.4 8. Q549.
PAGE 57
IC Data Sheets 8. EN 57 Diagram SSB: Ethernet B07G, DP83816 (IC7N04) Pin Configuration NC VSS NC AUXVDD VSS TXCLK TXEN C RS COL/MA16 AUXVDD VSS TXD3/MA15 TXD2/MA14 TXD1/MA13 TXD0/MA12 AUXVDD VSS C1 X2 X1 VSS RXDV/MA11 RXER/MA10 RXOE RXD3/MA9 RXD2/MA8 RXD1/MA7 AUXVDD VSS RXD0/MA6 RXCLK M DC MDIO M A5 MA4/EECLK MA3/EEDI Block Diagram TPTDP/M RAM BIST Logic SRAM RXFilter .
PAGE 58
EN 58 8.6 8. IC Data Sheets Q549.2E LA Diagram SSB: Audio B10A, TPA3123D (IC 7D10) Block Diagram 1 F 0.22 F LIN BSR RIN ROUT 1 F 22 H 0.68 F PGNDR 0.68 F PGNDL 1 F 470 F LOUT BYPASS AGND 22 H BSL 470 F 0.
PAGE 59
Block Diagrams Q549.2E LA 9. EN 59 9. Block Diagrams Wiring Diagram 32" (Elite Core) WIRING DIAGRAM 32" (ELITE CORE) WIFI ANTENNA WIFI ANTENNA (1044) (1043) LCD DISPLAY (1004) 1M83 (AL1) 8684 TO BACKLIGHT 1G50 (B05C) 41. N.C 40. TXDAT39.TXDAT ... ... ... 3. TX2E+ 2. SCL-DISP 1. SDA-DISP 8151 SCL-AMBI-3V3 GND SDA-AMBI-3V3 GND GND +3V3 GND 8159 1M59 (B06A) 8319 8316 1M85 (AL4) 14. GND 13. VLED2 12. GND 11. VLED1 10. PROG 9. TEMP-SENSOR 8. EEPROM-CS 7. BLANK-BU 6. +3V3 5. PWM-CLOCK-BUF 4.
PAGE 60
Block Diagrams Q549.2E LA 9. EN 60 Wiring Diagram 37" (Elite Core) WIRING DIAGRAM 37" (ELITE CORE) WIFI ANTENNA WIFI ANTENNA (1044) (1043) 8802 8802 1M83 (AL1) 1. SCL 2. GND 3. SDA 4. CONTROL-1 5. CONTROL-2 6. +3V3 7. GND 8. EEPROM-CS 9. TEMP-SENSOR 10. PROG 11. VLED1 12. GND 13. VLED2 14. GND 8684 LCD DISPLAY (1004) TO BACKLIGHT TO BACKLIGHT 8319 AMBI-LIGHT MODULE 3/3 (1075) SCL-AMBI-3V3 GND SDA-AMBI-3V3 GND GND +3V3 GND 1. 2. 3. 4. 5. 6. 7.
PAGE 61
Block Diagrams Q549.2E LA 9. EN 61 Wiring Diagram 56" (Elite Core) WIRING DIAGRAM 56" (ELITE CORE) 8583 8586 8587 8588 Component Level Repair Only For Authorized Workshop 8589 8590 CN2 CN1 CN3 41P 51P 5P TO BACKLIGHT 11. NC 10. GND_SND 9. +VSND 8. +12V 7. +12V 6. +12V 5. GND1 4. GND1 3. GND1 2. STANDBY 1. 3V3_ST SSB 124P (1011) 1M20 (B01B) 14. GND 13. VLED2 12. GND 11. VLED1 10. PROG 9. TEMP-SENSOR 8. EEPROM-CS 7. BLANK-BUF 6. +3V3 5. PWM-CLOCK-BUF 4. SPI-LATCH1CONN 3.
PAGE 62
Block Diagrams Q549.2E LA 9.
PAGE 63
Block Diagrams Q549.2E LA 9.
PAGE 64
Block Diagrams Q549.2E LA 9. EN 64 Block Diagram Control & Clock Signals CONTROL + CLOCK SIGNALS B07A CI: PCMCIA CONNECTOR 7N04 DP83816AVNGNOPB 7H00 PNX85439EH/M2 B04N TUN_CA ETHERNET CONNECTOR 25M 1N02 ETHERNET CONTROLLER B04A 60 PCI-CLK-ETHERNET 61 1P00 1 CA-MICLK H32 CA-MDI(0-7) IRQ-PCI MOCLKA SSB_31043136343.
PAGE 65
Block Diagrams Q549.2E LA 9.
PAGE 66
Block Diagrams Q549.2E LA 9.
PAGE 67
Circuit Diagrams and PWB Layouts Q549.2E LA 10. EN 67 10. Circuit Diagrams and PWB Layouts Ambilight Interface: Interf.
PAGE 68
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 69
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 70
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 71
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 72
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 73
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 74
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 75
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 76
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 77
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 78
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 79
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 80
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 81
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 82
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 83
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 84
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 85
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 86
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 87
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 88
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 89
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 90
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 91
Circuit Diagrams and PWB Layouts Q549.2E LA 10. EN 91 SSB: PNX8543 - Debug 1 Personal Notes: 3 2 4 6 5 A A 1H11 C2 B 2H06 C3 2H07 D3 3HF3 A3 6HF0 B3 1 FH00 C2 FH08 D3 IH93 C2 IH94 C3 B IH95 D2 4 3 C PNX8543 : DEBUG A A +3V3-PER SML-310 6HF0 E B D 330R 3HF3 D BE 7HF2 PDTC114EU RESET-SYSTEM SPI-PROG G SDM D F 2H06 RES TSTPOINT FOR DEBUG C 100p SPI-PROG IH94 GND TSTPOINT FOR DEBUG 3 SKHUBHE010 1H11 2 C IH93 FH00 1 F 4 owner.
PAGE 92
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 93
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 94
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 95
Circuit Diagrams and PWB Layouts Q549.2E LA 10. EN 95 SSB: PNX8543 - Digital Video In 1 5 4 3 2 1 A 6 2 8 7 3 9 4 11 10 6 5 12 3HK0 B2 7H00-4 A3 9HK0 D2 IHSM B2 TH01 C2 TH02 C2 TH03 C2 TH04 C2 TH05 C2 TH06 C2 TH07 D2 TH08 D2 TH09 B2 TH10 B2 TH11 B2 TH12 B2 TH13 B2 TH14 C2 TH15 C2 TH16 C2 7 PNX 8543 : DIGITAL VIDEO IN B A A 7H00-4 PNX85439EH/M2/24182 B C18 E19 DDC-SCL DDC-SDA RREF-PNX85XX C15 D15 HDMIA-RX0HDMIA-RX0+ D C owner. All rights reserved.
PAGE 96
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 97
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 98
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 99
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 100
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 101
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 102
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 103
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 104
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 105
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 106
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 107
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 108
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 109
Circuit Diagrams and PWB Layouts Q549.2E LA 10. EN 109 SSB: PNX5100 - PCI 2 1 4 3 2 1 6 5 3 8 7 4 5 6 11 10 9 7 13 12 3CF1 C5 3CFK-1 B5 3CFK-2 B5 3CFK-3 B5 3CFL-1 B5 3CFL-2 B5 3CFL-3 B5 3CFN B5 7C00-2 A3 IC50 C5 IC51 C5 8 A PNX5100 : PCI A B owner. All rights reserved.
PAGE 110
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 111
Circuit Diagrams and PWB Layouts Q549.2E LA 10. EN 111 SSB: PNX5100 - Debug 1 2 4 3 Personal Notes: 6 5 A A 3CJ0 C3 3CJ1 C3 6CJ0 C3 7CJ0 D3 FCJ0 D3 B B 1 2 4 PNX5100 : DEBUG C A C A RESERVED D D B B +3V3 C 3CJ0 10K F E +3V3 F 330R E 3CJ1 C PNX5100-RST-OUT 6CJ0 SML-310 owner. All rights reserved.
PAGE 112
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 113
Circuit Diagrams and PWB Layouts Q549.2E LA 10. EN 113 SSB: U-Wand 4 Personal Notes: 6 5 A A B B 1F10 B3 1R20 A3 C 5FC5 A3 5FC6 A2 5FC7 A3 5FC8 A2 5FC9 A3 FFC2 A3 FFC5 A3 FFHB B3 FFC3 A3 FFC4 A3 1 FFHC B3 FFHD B3 FFHE B3 FFHF C3 FFHG C3 FFHH C3 FFHJ C3 FFHK C3 3 2 D FFHL C3 IFC0 A2 IFC1 A3 IFC5 A2 C 4 D U-WAND RES U-WAND owner. All rights reserved.
PAGE 114
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 115
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 116
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 117
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 118
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 119
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 120
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 121
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 122
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 123
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 124
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 125
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 126
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 127
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 128
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 129
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 130
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 132
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 133
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 134
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 135
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 136
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 137
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 138
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 139
Circuit Diagrams and PWB Layouts Q549.2E LA 10.
PAGE 140
Circuit Diagrams and PWB Layouts Q549.2E LA 10. EN 140 3015 6007 6008 3009 6006 3008 2001 3007 6005 3005 7001 6004 2002 6003 3004 6002 3003 6001 3002 3001 3016 Layout guide panel 6009 3000 I010 I009 1P09 I008 I001 I000 I005 I004 I006 I007 I003 I002 18310_559_090420.eps 090508 31043136344.
PAGE 141
Circuit Diagrams and PWB Layouts Q549.2E LA 10. EN 141 Wi-Fi Antenna Layout Wi-Fi Antenna 2 3 4 5 6 A A B B C C 1000 1000 B1 1 W D 2 3 WIFI ANTENNA D A owner. All rights reserved. Reproduction in whole or in parts is prohibited without the written consent of the copyright 1 A E E 3104 313 6328.2 1000 U.