BDL4988XC 49BDL3005X V1.30 www.philips.
BDL4988XC/49BDL3005X Safety Instructions Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards. Read and follow these instructions when connecting and using your display: Operation: • Keep the display out of direct sunlight and away from stoves or any other heat sources.
BDL4988XC/49BDL3005X Read and follow these instructions when connecting and using your display: • Unplug the display if you are not going to use it for an extensive period of time. • Unplug the display if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth when the power is off. However, never use alcohol, solvents or ammonia-based liquids.
BDL4988XC/49BDL3005X Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, display, printer, and so on) should have the same power supply source. The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A).
BDL4988XC/49BDL3005X Information for U.K. only WARNING - THIS APPLIANCE MUST BE EARTHED. (B) Important: (A) This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place.
BDL4988XC/49BDL3005X 中国大陆RoHS 根据中国大陆《电子电气产品有害物质限制使用标识要求》,以下部分列出了本产品中可能包含的有害物 质的名称和含量。 有害物质 部件名称 铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr (VI)) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 外壳 ○ ○ ○ ○ ○ ○ 液晶显示屏 × ○ ○ ○ ○ ○ 电路板组件* × ○ ○ ○ ○ ○ 电源适配器 × ○ ○ ○ ○ ○ 电源线/连接线 × ○ ○ ○ ○ ○ 遥控器 X ○ ○ ○ ○ ○ 本表格依据SJ/T 11364 的规定编制。 *: 电路板组件包括印刷电路板及其构成的零部件,如电阻、电容、集成电路、连接器等。 O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572规定的限量要求以下。 X: 表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572规定的限量要求。 上表中打“×”的部件,应功能需要,部分有害物质含量超出GB/T 26572规定的
BDL4988XC/49BDL3005X 《废弃电器电子产品回收处理管理条例》提示性说明 为了更好地关爱及保护地球,当用户不再需要此产品或产品寿命终止时,请遵守国家废弃电器电子产品 回收处理相关法律法规,将其交给当地具有国家认可的回收处理资质的厂商进行回收处理。 娤⌈ 㨢᳸$䵥ᵥ⍿Ʋ◦䏝㯹䉭❁ᳫ濕媣ᵥ⍿⊭侻ᷘ廞ノ㒞䵽䏳ⴰㄮƲ◦店䢋⾃濕⊭侻斾堿䏦ヵ ⪷ⴰㄮ悅⊔⩜⊭圊䕂㉨㑻Ʋ 限用物質及其化學符號 單元 鉛 (Pb) 汞 (Hg) 鎘 (Cd) 六價鉻 (Cr+6) 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) 塑料外框 ○ ○ ○ ○ ○ ○ 後殼 ○ ○ ○ ○ ○ ○ 液晶面板 - ○ ○ ○ ○ ○ 電路板組件 - ○ ○ ○ ○ ○ 底座 ○ ○ ○ ○ ○ ○ 電源線 - ○ ○ ○ ○ ○ 其他線材 - ○ ○ ○ ○ ○ 遙控器 - ○ ○ ○ ○ ○ 喇叭(選配) - ○ ○ ○ ○ ○ 風扇(選配) - ○ ○ ○ ○
BDL4988XC/49BDL3005X End-of-Life Disposal Your new Public Information Display contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of. Please find out about the local regulations on how to dispose of your old display from your local Philips dealer. (For customers in Canada and U.S.A.) This product may contain lead and/or mercury.
BDL4988XC/49BDL3005X Batteries For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in accordance with legislation. Please contact your local authority for details on the collection and recycling schemes. For Switzerland: The used battery is to be returned to the selling point.
BDL4988XC/49BDL3005X Table Of Contents 1. Unpacking and Installation........................................................1 1.1. Unpacking..........................................................................................1 1.2. Package Contents.........................................................................1 1.3. Installation Notes..........................................................................1 1.4. Mounting on a Wall............................................................
BDL4988XC/49BDL3005X 1. Unpacking and Installation 1.1. Unpacking • This product is packed in a carton, together with the standard accessories. • Any other optional accessories will be packed separately. • As this product is high and heavy, the operation of moving the device is recommended to be performed by two technicians. • After opening the carton, ensure that the contents are complete and in good condition. 1.2.
BDL4988XC/49BDL3005X 1.4. Mounting on a Wall To mount this display on a wall, a standard wall-mounting kit (commercially available) is required. It is recommended that you use a mounting interface that complied with TUV-GS and /or UL1678 standard in North America. Protective Sheet VESA Grid Table Tabletop stand 1. Spread a protective sheet on a flat surface, which is wrapped around the display when it was packed, beneath the screen surface to facilitate your operation without scratching the screen.
BDL4988XC/49BDL3005X 1.5. Mounting in Portrait Position This display can be installed in portrait position. 1. If the table stand is attached, remove it first. 2. Rotate the display counterclockwise by 90°.The “ ” logo should be in a vertical position when facing the display from the back.
BDL4988XC/49BDL3005X 1.6. Operating Instructions of Edge Alignment Kit 1.6.1. Installing the Edge Alignment Kit • Before installing the edge alignment kit, the display must be mounted to the frame of video wall correctly. • Use the provided thumb screw to facilitate your installation of the edge alignment kit. • Use the “Edge Alignment Kit-1” for four adjacent displays. 2 3 1 4 5 8 7 • 6 Use the “Edge Alignment Kit-2” for two adjacent displays.
BDL4988XC/49BDL3005X 1.7. Using of Edge Finishing Kit (Optional) You can use the edge finishing kit to protect the display and have a better appearance. 1.7.1.
BDL4988XC/49BDL3005X 2. Parts and Functions 2.1. Control Panel 9 MUTE INPUT 1 1 2 3 MENU 4 5 6 7 8 [ ] button 9 Turn the display On or turn the display to standby mode. 2 [MUTE] button -- When {SCHEDULE} is enabled, the light blinks green and red Work as a [ ] button to confirm a selection in the OnScreen-Display menu.
BDL4988XC/49BDL3005X 2.2. Input/Output Terminals 24 23 21 20 2 1 1 3 7 4 5 6 17 19 14 8 10 11 12 13 15 16 18 9 AC IN 13 MAIN POWER SWITCH 15 AC OUT 16 AC power input from the wall outlet. 2 IR IN / 5 IR OUT 17 18 7 19 20 RS232C OUT 21 RJ-45 HDMI1 IN / 10 22 AUDIO IN AUDIO OUT USB PORT Connect to a USB storage device. HDMI2 IN 23 SPEAKERS OUT Audio output to external speakers. DVI IN Connect to a source device using a DVI cable.
BDL4988XC/49BDL3005X damage caused by using other type of OPS module is not covered by the warranty. 4 Remote Control 5 2.3.1. General functions 6 2.3. [ ] HOME button Access the OSD menu. [ ] LIST button (Reserved). [ ] [ ] [ ] [ ] NAVIGATION buttons Navigate through the menu and select an item. 7 1 [ ] button Confirm an entry or selection. 8 [ ] ADJUST button Access currently available options, picture and sound menus. 9 2 [ ] MUTE button Mute the sound or reactivate sound.
BDL4988XC/49BDL3005X 2.3.2. ID Remote Control 4. Press [ENTER] button to confirm your selection. The red LED blinks twice and then lights off. Set the remote control ID if you intend to use this remote control on several different displays. NOTE: Press the [ID] button and the red LED blinks twice. 1. Press the [ID SET] button for more than 1 second to enter the ID mode. The red LED lights up. Pressing the [ID SET] button again will exit from the ID mode. The red LED lights off.
BDL4988XC/49BDL3005X 2.3.3. Inserting the batteries in the remote control The remote control is powered by two 1.5V AAA batteries. To install or replace the batteries: 1. Press and then slide the cover to open it. 2. Insert the batteries with the correct polarity (+) and (-). 3. Replace the cover. Caution: Incorrect use of batteries may cause leakage or explosion. Be sure to follow the instructions below: • Insert “AAA” batteries with the correct polarity (+ and -). • Do not mix battery types.
BDL4988XC/49BDL3005X 3. Connecting External Equipment 3.1. Connecting External Equipment (DVD/VCR/VCD) 3.1.1. Using COMPONENT video input Audio Out COMPONENT Out (YPbPr) [R] [L] DVD / VCR / VCD [AUDIO IN] [COMPONENT IN] (YPbPr) 3.1.2.
BDL4988XC/49BDL3005X 3.1.3. Using HDMI video input DVD / VCR / VCD HDMI Out [HDMI IN] 3.2. Connecting a PC 3.2.1. Using VGA input VGA Out D-Sub 15 pin Audio Out PC [VGA IN] [VGA AUDIO IN] 3.2.2.
BDL4988XC/49BDL3005X 3.2.3. Using HDMI input HDMI Out PC [HDMI IN] 3.2.4. Using DisplayPort input DisplayPort Out PC [DisplayPort IN] 3.3. Connecting Audio Equipment 3.3.1.
BDL4988XC/49BDL3005X 3.3.2. Connecting an external audio device Audio In Stereo Amplifier [AUDIO OUT] 3.4. Connecting Multiple Displays in a Daisy-chain Configuration You can interconnect multiple displays to create a daisy-chain configuration for applications such as a video wall. 3.4.1. Display control connection Connect the [RS232C OUT] connector of DISPLAY 1 to the [RS232C IN] connector of DISPLAY 2.
BDL4988XC/49BDL3005X 3.4.2. Digital video connection Connect the [DVI OUT / VGA OUT] connector of DISPLAY 1 to the [DVI IN] connector of DISPLAY 2. DISPLAY 1 DISPLAY 2 PC [DVI] [DVI IN] [DVI/VGA OUT] [DVI IN] Connect the [DP OUT] connector of DISPLAY 1 to the [DP IN] connector of DISPLAY 2. DISPLAY 1 DISPLAY 2 PC [DP] [DP IN] [DP OUT] [DP IN] Connect the [DVI OUT ] connector of DISPLAY 1 to the [DVI IN] connector of DISPLAY 2.
BDL4988XC/49BDL3005X 3.5. IR connection External IR Receiver [IR IN] NOTE: The remote control sensor of this display will stop working if the [IR IN] is connected. 3.6.
BDL4988XC/49BDL3005X 3.7. Wire-connecting to Network By connecting this display to a home network, you can play photos, music and videos from your computer. See Play multimedia files via Local Area Network (Page 18) for details. INTERNET ROUTER [RJ-45] [RJ-45] PC Network settings: 1. Switch the router On and enable its DHCP setting. 2. Connect the router to this display with an Ethernet cable. 3. Press [ ] HOME button on the remote control, then select Setup. 4.
BDL4988XC/49BDL3005X 4. Operation • Multiple display setup: NOTE: T he control button described in this section is mainly on the remote control unless specified otherwise. 4.1. DISPLAY 1 Watch the Connected Video Source ROUTER [RJ-45] DISPLAY 2 [RJ-45] [RJ-45] PC See page 11 for external equipments connection. 1. Press [ ] SOURCE button. 2. Press [ ] or [ ] button to select a device, then press [ 4.2.
BDL4988XC/49BDL3005X 4. You can connect up to 4 displays to the same PC and play the same media stream. 6. Check the media formats. Then, click Choose media streaming options..... 4.3.3. How to use DLNA-DMR from PC 7. Go to Advanced sharing settings, and click the checkbox Turn on network discovery. 1. Press [ button. ] HOME button, select Network and press [ ] Picture Network settings 8. Go to the directory of your media files and select the media file by right clicking on it.
BDL4988XC/49BDL3005X 4.5.3. Playing photo files 7. Press [PLAY] buttons (H F G I J) to control playback. 4.5. 1. Select Play options Photo from the top menu bar. Photo 4.5.1. Playing music files 1. Select 2. Select a photo thumbnail, then press [ Music from the top menu bar. If there are multiple photos in a folder, select one and press [ ] to Play All. Music 2. Select one music track and press [ ] button. • To play all tracks in a folder, select one music file. Then, press [ ] to Play All.
BDL4988XC/49BDL3005X Internet Web Address:X http:// History www.google.com w ww.google.com Bookmark . , @ ‘ a b c d e f g i j k l m n o p q r s t v w x y z h u < abc Done Hide ? ! - ABC 123 www 3. Move the cursor to “” icon and press [ Backspace ] button. Internet Web Address:X http://www.google.com History www.google.com w ww.google.com Bookmark 4. A web page appears as shown below: NOTES: • The Opera browser does not support FLASH format.
BDL4988XC/49BDL3005X 5. Change your settings 5.1.1. Picture Using the remote control: SOURCE FORMAT Picture Picture style Sound Backlight Tiling Colour Network Sharpness General settings Noise reduction Advanced MPEG artifact reducti... um ne Help LIST Picture enhancement INFO Advanced Scan mode Format and edges HDMI input range Picture reset ADJUST OPTIONS Picture style Select a predefined picture setting. 1. Press [ ] button on the remote control to display the OSD menu.
BDL4988XC/49BDL3005X • {V Zoom}: Expand the vertical size of image only. Note: Zoom, H Zoom and V Zoom are available only when the Picture format setting is set to Custom Zoom. See page 18 for the descriptions about Picture format. HDMI input range Color ranges of HDMI video format • {Auto}: Automatic color range of HDMI video format. • {Limit}: Limited range of HDMI video format. • {Full}: Full range of HDMI video format.
BDL4988XC/49BDL3005X Example: 2 x 2 screen matrix (4 displays) H monitors = 2 displays V monitors = 2 displays {Off} V monitors H monitors 1 2 3 4 Position Example: 5 x 5 screen matrix (25 displays) H monitors = 5 displays V monitors = 5 displays Frame comp.H Adjust the horizontal frame compensation. V monitors H monitors 1 2 3 4 5 6 11 7 12 8 13 9 14 10 15 16 21 17 22 18 23 19 24 20 25 Frame comp.V Adjust the vertical frame compensation.
BDL4988XC/49BDL3005X 1 5 2 3 6 7 5.1.5. General settings 4 8 9 10 11 12 13 14 15 16 Picture Menu language Sound Monitor Group Tiling Monitor ID Network Eco mode General settings Auto search Advanced Clock Help Scheduling Sleep timer OneWire Local KB lock RC lock Note 1: To use this function, serially connect all machines with RS-232 cable and set their Network control port to RS-232. Note 2: To use this function for DP 1.
BDL4988XC/49BDL3005X • Menu item {Correction time} Selection item {0.5, 1.0, 1.5, 2.0} hour • Menu item {Daylight saving} Selection item {on, off} Schedule 1 Status USB playlist When “daylight saving” is “on”, the real time clock will be adjusted automatically at the daylight saving time (e.g. April 5, 2015, 02.00 o’clock: time will be set 1 hour later or October 25, 2015, 02.00 o’clock: time will be set 1 hour earlier).
BDL4988XC/49BDL3005X 6. If {Source} {USB} is selected, go to Playlist setting. 0001/0002 Photo Photo Video • {Unlock}: Enable the remote control function. • {Lock all}: Lock all remote control functions. • {Lock but volume}: Disable all remote control functions except the [ ] and [ ] button. • {Lock but power}: Disable all remote control functions except the [ ] POWER button.
BDL4988XC/49BDL3005X 5.1.7. Help DisplayPort Ver. Set the DisplayPort version to 1.1a or 1.2, this setting is only valid on DisplayPort input and output, Picture 1.1a: Switch DisplayPort Ver. to 1.1a(default), the DisplayPort output is the clone of DisplayPort input. Sound 1.2: Switch DisplayPort Ver. to 1.2 to support MST(Multi-Stream Transport) Network NOTES: Advanced • If the display shows a black screen or works abnormally under DisplayPort source, please switch to 1.
BDL4988XC/49BDL3005X 6. USB device compatibility USB Video Subtitle Formats (for language subtitles, etc.) File Extensions Container .mpg mpeg PS .vob .ts TS Video codec Maximum resolution Max.Frame Rate (fps) Max.Bit Rate (Mbps) Audio codec MPEG-1 1920x1080 25p,30p,50i,60i 30 MPEG-1(L1&L2), MPEG-2 1920x1080 25p,30p,50i,60i 30 MPEG-1,2,2.5 L3, MPEG-4 ASP 1920x1080 25p,30p,50i,60i 30 AAC/HE-AAC(v1&v2), H.
BDL4988XC/49BDL3005X USB Multimedia Formats File Extensions Frequency Max.Bit Rate (kHz) (Mbps) - 48 384 MPEG-1,2,2.5 L3 - - 48 192 WMA Container Video codec Maximum resolution - Audio codec .mp3 MP3 .wma WMA .asf (V2 up to V9.2) .wma WMA Pro - - 96 768 WMA,WMA Pro .wav(PC) LPCM - - 192 768 LPCM LPCM - - 192 768 LPCM AAC - - 48 1024 AAC,HE-AAC(v1&v2) Playlists - - - - - M4A - - 48 1024 AAC,HE-AAC(v1&v2) .aif(mac) .aiff(mac) .aac .mp4 .m4a .
BDL4988XC/49BDL3005X 7. Input Mode VGA Resolution: Standard Resolution Active Resolution H Pixels V Lines VGA 640 480 WVGA 720 400 SVGA 800 600 XGA 1024 768 WXGA WXGA SXGA SXGA WXGA WXGA UXGA HD1080 1280 1280 1280 1280 1360 1366 1600 1920 768 800 960 1024 768 768 1200 1080 Refresh Rate Pixel Rate Aspect Ratio Stand for Mode 60 Hz 72 Hz 75 Hz 70 Hz 60 Hz 75 Hz 60 Hz 75 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 25.175 MHz 31.5 MHz 31.5 MHz 33.75 MHz 40 MHz 49.5 MHz 65 MHz 78.
BDL4988XC/49BDL3005X 8. Pixel Defect Policy We strive to deliver the highest quality products and use some of the industry’s most advanced manufacturing processes whilst practicing stringent quality control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCD- displays are sometimes unavoidable.
BDL4988XC/49BDL3005X 8.4. Dark Dot Defects Black dot defects appear as pixels or sub-pixels that are always dark or “off ”. These are the examples of black dot defects: One dark dot 8.5.
BDL4988XC/49BDL3005X 9. Cleaning and Troubleshooting 9.1. Cleaning Caution When Using the Display • Do not bring your hands, face or objects close to the ventilation holes of the display. The top of the display is usually very hot due to the high temperature of exhaust air being released through the ventilation holes. Burns or personal injuries may occur if any body parts are brought too close.
BDL4988XC/49BDL3005X 9.2. Troubleshooting Symptom Possible Cause Remedy No picture is displayed 1. The power cord is disconnected. 1. Plug in the power cord. 2. The main power switch on the back of the display is not switched on. 2. Make sure that the power switch is switched on. 3. The selected input has no connection. 3. Connect a signal connection to the display. 4. The display is in the standby mode.
BDL4988XC/49BDL3005X How to setup the settings in the menu to control all the monitors at the same time and individually via RC? Daisy chained by RS232 and no IR cable 1. The first display sets as “Primary” on OSD (Advanced option/IR control item), others set as “Secondary”. 2. The setup OSD will show on top left side of the display.(Toggle MENU will show again if it disappears) 3. Default setting: ID NO: 0, GP NO: 0, this setting can control all displays by IR.
BDL4988XC/49BDL3005X 10. Technical Specifications Display: Item Specifications Screen Size (Active Area) 48.5” (123.2 cm) LCD Aspect Ratio 16:9 Number of pixels 1920 (H) x 1080 (V) Pixel pitch 0.559 (H) x 0.559 (V) [mm] Displayable colors 1.
BDL4988XC/49BDL3005X General: Item Specifications Power Input 100 - 240V~, 50 - 60Hz, 6.0A Power Output 100 - 240V~, 50 - 60Hz, 2.5A Power Consumption (Max) 235 W Power Consumption (typ.) 110 W Power Consumption (Standby & Off) <0.5 W (RS232 in active) Dimensions (without stand) [W x H x D] 1077.7 x 607.9 x 93.5 (@Wall mount) / 103.8 (@Handle) Weight (without stand) 21.6 Kg Gross Weight (without stand) 33.5 Kg Energy Efficiency Class A Visible Screen Size 123.2 cm / 48.
2017 © Koninklijke Philips N.V. All rights reserved. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license from Koninklijke Philips N.V. Specifications are subject to change without notice.