Specifications

ManualsBrandsPhilips ManualsTV23PF9956/12

Published by BB 0466 Service PaCE Printed in the Netherlands Subject to modification EN 3122 785 14491

retrieval system or transmitted, in any form or by any means, electronic,

mechanical, photocopying, or otherwise without the prior permission of Philips.

Colour Television Chassis

LC4.2E

E_14490_000.eps

110604

Contents Page Contents Page

1. Technical Specifications, Connections,

and Chassis Overview 2

2. Safety and Maintenance Instructions,

Warnings, and Notes 5

3. Directions for Use 7

4. Mechanical Instructions 8

5. Service Modes, Error Codes, and Faultfinding 11

6. Block Diagrams, Testpoint Overviews,

and Waveforms

Wiring Diagram 19

Block Diagram Tuner and IF Video 20

Block Diagram Scaler 21

Testpoint Overview Tv & Scaler Board 22-23

I2C Overview 24

Supply Voltage Overview 25

7. Circuit Diagrams and PWB Layouts Diagram PWB

Tuner + VIF (Diagram A1) 26 38-47

Hercules (Diagram A2) 27 38-47

Histogram (Diagram A3) 38 38-47

Audio Amplifier (Diagram A5) 29 38-47

TV-Supply (Diagram A6) 30 38-47

Scaler (Diagram A7) 31 38-47

Scaler Interface (Diagram A9) 32 38-47

SDRAM (Diagram A10) 33 38-47

Flash / Control (Diagram A11) 34 38-47

HDMI (Diagram A12) 35 38-47

PCHD-MUX (Diagram A13) 36 38-47

Supply (Diagram A14) 37 38-47

Side IO and LKB Panel (Diagram D) 48 49

Rear IO Panel: Scart (17”) (Diagram H1) 50 52

Rear IO Panel: PCHD-IO (17”) (Diagram H2) 51 52

Rear IO Panel: Scart (23/26”) (Diagram H1) 53 55

Rear IO Panel: PCHD-IO (23/26”)(Diagram H2) 54 55

Front IR / LED Panel (Diagram J) 56 56

Pixel Plus Panel: EPLD Control (Diagram PP1)57 61

Pixel Plus Panel: LVDS In (Diagram PP2) 58 61

Pixel Plus Panel: EPLD I/O (Diagram PP3) 59 61

Pixel Plus Panel: Power Supply (Diagram PP4) 60 61

8. Alignments 63

9. Circuit Descriptions 66

Abbreviation List 72

IC Data Sheets 74

10 Spare Parts List 77

11 Revision List 82

Summary of content (82 pages)

PAGE 1
Colour Television Chassis LC4.2E AA E_14490_000.eps 110604 Contents Page 1. Technical Specifications, Connections, and Chassis Overview 2 2. Safety and Maintenance Instructions, Warnings, and Notes 5 3. Directions for Use 7 4. Mechanical Instructions 8 5. Service Modes, Error Codes, and Faultfinding 11 6.
PAGE 2
EN 2 1. Technical Specifications, Connections, and Chassis Overview LC4.2E AA 1. Technical Specifications, Connections, and Chassis Overview Note: Figures below can deviate slightly from the actual situation, due to the different set executions. 1.2 Connections 1.2.1 Rear Connections AERIAL IN 1.1 Technical Specifications 1.1.
PAGE 3
Technical Specifications, Connections, and Chassis Overview 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 C5 External 2: RGB/YUV - In and CVBS - In/Out 20 2 21 1 E_06532_001.eps 050404 Figure 1-3 SCART connector 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 - Audio - R 0.5 V_rms / 1 kohm - Audio - R 0.5 V_rms / 10 kohm - Audio - L 0.5 V_rms / 1 kohm - Audio - gnd Ground - Blue - gnd Ground - Audio - L 0.5 V_rms / 10 kohm - n.c. - CVBS - status 0 - 2 V: INT 4.5 - 7 V: EXT 16:9 9.
PAGE 4
EN 4 1. LC4.2E AA Technical Specifications, Connections, and Chassis Overview LCD PANEL TV & SCALER BOARD PIXEL PLUS PANEL SIDE IO PANEL P POWER SUPPLY UNIT A PP D FRONT LED PANEL J REAR I/O CINCH PANEL H E_14490_100.
PAGE 5
Safety Instructions, Warnings, and Notes LC4.2E AA 2. EN 5 2. Safety Instructions, Warnings, and Notes 2.1 Safety Instructions Safety regulations require that during a repair: • Connect the set to the Mains via an isolation transformer (> 800 VA). • Replace safety components, indicated by the symbol h, only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of fire or electrical shock hazard.
PAGE 6
EN 6 2. LC4.2E AA Safety Instructions, Warnings, and Notes Device Replacement The last step in the repair process is to solder the new component on the board. Ideally, the (LF)BGA should be aligned under a microscope or magnifying glass. If this is not possible, try to align the (LF)BGA with any board markers. To reflow the solder, apply a temperature profile according to the IC data sheet. So as not to damage neighbouring components, it may be necessary to reduce some temperatures and times.
PAGE 7
Directions for Use 3. Directions for Use You can download this information from the following website: http://www.philips.com/support LC4.2E AA 3.
PAGE 8
EN 8 4. Mechanical Instructions LC4.2E AA 4. Mechanical Instructions Index of this chapter: 1. Service Position 2. Rear Cover Removal 3. Power Supply Unit Removal 4. TV & Scaler Board Removal 5. I/O Panel Removal 6. Side I/O & Keyboard Panel and Front LED Panel Removal 7. Pixel Plus Panel Removal 8. Exchanging the LCD Panel 9. Re-assembly 4 Note: Figures below can deviate from the actual situation, due to different set executions.
PAGE 9
Mechanical Instructions 4.2 4.4 Rear Cover Removal 3 LC4.2E AA 4. EN 9 TV & Scaler Board Removal 3 3 3 1 1 3 2 2 3 1 3 3 E_14490_006.eps 130404 E_14490_004.eps 130404 Figure 4-7 : TV & Scaler board shield removal Figure 4-5 Rear cover removal 1. Manually unlock and remove the top cover cap (5). See Figure: “TV set rear view”. 2. Make sure all power-, audio-, video- and coax- cables are unplugged. 3. Remove all Torx screws (1) around the edges of the rear cover. 4.
PAGE 10
EN 10 4. LC4.2E AA Mechanical Instructions 1. Release the two clamps (1) at the I/O panel bracket. Carefully pull the bracket in the direction (2), as shown at the figure “I/O panel removal”, and remove it. 2. Disconnect all cables from the I/O panel. 3. Remove all mounting screws from the I/O panel (3). 4. Take out the I/O panel. 4.6 4.8 Exchanging the LCD Panel Side I/O & Keyboard Panel and Front LED Panel Removal 1 1 1 4 2 3 E_14490_010.eps 130404 1 Figure 4-12 Exchanging the LCD panel 1.
PAGE 11
Service Modes, Error Codes, and Fault Finding LC4.2E AA 5. EN 11 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: 1. Test Points 2. Service Modes 3. Problems and Solving Tips (related to CSM) 4. ComPair 5. Error Codes 6. The Blinking LED Procedure 7. Fault Finding and Repair Tips 8. Power Supply 5.1 Test Points This chassis is equipped with test points in the service printing. In the schematics test points are identified with a rectangle box around Fxxx or Ixxx.
PAGE 12
EN 12 5. Service Modes, Error Codes, and Fault Finding LC4.2E AA After entering SDM, the following screen is visible, with SDM in the upper right corner of the screen to indicate that the television is in Service Default Alignment Mode. 00022 LC42EP1 0.08/S42GV1 0.90 SDM ERR 0 0 0 0 0 After entering SAM, the following screen is visible, with SAM in the upper right corner of the screen to indicate that the television is in Service Alignment Mode. 00022 LC42EP1 0.08/S42GV1 0.
PAGE 13
Service Modes, Error Codes, and Fault Finding 11. NVM Editor. Can be used to change the NVM data in the television set. See table “NVM data” further on. 12. SC NVM Editor. Can be used to edit Scaler NVM. 13. ComPaIr. Can be used to switch on the television to In System Programming (ISP) mode, for software uploading via ComPair. Caution: When this mode is selected without ComPair connected, the TV will be blocked. Remove the AC power to reset the TV. 1 00022 LC42EP1 0.08/S42GV1 0.
PAGE 14
EN 14 5. LC4.2E AA Service Modes, Error Codes, and Fault Finding 6. Press the MENU RIGHT key to increase the COLOUR value. 7. Press the MENU button on the remote control transmitter twice to exit the user menu. 8. The new PERSONAL preference value is automatically stored. Then: 1. Press the AUTO PICTURE button on the remote control transmitter repeatedly (if necessary) to choose PERSONAL picture mode. 2. Press the MENU button on the remote control transmitter. This brings up the normal user menu. 3.
PAGE 15
Service Modes, Error Codes, and Fault Finding communicate (read and write) to devices on the I2C busses of the TV-set. • Manually (by asking questions to you): Automatic diagnosis is only possible if the micro controller of the television is working correctly and only to a certain extend. When this is not the case, ComPair will guide you through the faultfinding tree by asking you questions (e.g. Does the screen give a picture? Click on the correct answer: YES / NO) and showing you examples (e.g.
PAGE 16
EN 16 5. Service Modes, Error Codes, and Fault Finding LC4.2E AA If possible, check the entire contents of the error buffer. In some situations, an error code is only the result of another error and not the actual cause of the problem (for example, a fault in the protection detection circuitry can also lead to a protection). 5.7.2 In case a blank NVM is placed or when the NVM content is corrupted, default values can be downloaded into the NVM.
PAGE 17
Service Modes, Error Codes, and Fault Finding 5.7.4 Video Processing No power 1. Check +12 V and 3V3 at position 1910. 2. If no supply, check the connector 1910. 3. If it is correct, check the power supply board. Power supply is correct but no green light 1. Check the two connectors 1005 and 1601, if they are properly inserted. 2. If they are inserted correctly, check if the 3V3 is present. No picture display 1. Check the RGB signal. 2. If it is present, check 3-IC7016 (NE555). 3.
PAGE 18
EN 18 5. LC4.2E AA Service Modes, Error Codes, and Fault Finding Personal Notes: E_06532_012.
PAGE 19
Block Diagrams, Testpoint Overviews, and Waveforms LC4.2E AA 6. 19 6.
PAGE 20
Block Diagrams, Testpoint Overviews, and Waveforms LC4.2E AA 6. 20 Block Diagram Tuner and IF Video SYSTEM HERCULES +VTUN 7014 31 RF_AGC A2 7320 CS1A..
PAGE 21
Block Diagrams, Testpoint Overviews, and Waveforms LC4.2E AA 6.
PAGE 22
Block Diagrams, Testpoint Overviews, and Waveforms LC4.2E AA 6.
PAGE 23
Block Diagrams, Testpoint Overviews, and Waveforms LC4.2E AA 6. 23 Testpoint Overview TV & Scaler Board (Top Side) SERVICE TESTPOINT F452 500mV / div DC 20us / div 3139 123 5804.2 E_14490_022.eps 030604 E_06532_012.
PAGE 24
Block Diagrams, Testpoint Overviews, and Waveforms LC4.2E AA 6. 24 I2C IC Overview I2C BUS INTERCONNECTION DIAGRAM A2 HERCULES A1 TUNER IF +3V3STBY +3V3STBY A3 HISTOGRAM A7 SCALER A11 FLASH/CONTROL ERR 6 3096 3088 F303 7011 109 SET PROCESSOR 108 PART OF VIDEOPROCESSER (HERCULES) +3V3STBY +3V3STBY SDA SCL 3433 3432 F302 3303 +3.
PAGE 25
Block Diagrams, Testpoint Overviews, and Waveforms LC4.2E AA 6.
PAGE 26
Circuit Diagrams and PWB Layouts LC4.2E AA 7. 26 7.
PAGE 27
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 28
Circuit Diagrams and PWB Layouts 4 28 5 6 7 8 9 HISTOGRAM G TO 1801 OF 3D COMB FILTER BD 34 1V2 3015 0R 3052 0R 2040 10u 16V A2 F031 SVHS_R_IN A2 F032 SC2_C_IN A13 B_SDTV F033 2082 STATUS_2 A2 A2 SC2_Y_IN SC2_L_IN A2 A2 A2 RO A2 GO I060 3049 100R 3050 100R BO 2083 SC1_COMP_AV1_G_Y_CVBS_IN SC1_CVBS_IN SC1_COMP_B_U_IN SC1_COMP_R_V_IN 2054 1n0 F043 F044 F045 A2 SC1_COMP_AV2_R_IN A2 SC1_CVBS_RF_OUT SC1_FBL_IN SC1_L_RF_OUT P50 SC1_R_RF_OUT A2 A2 A2 A2 A2 A2 A2 A2 A2
PAGE 29
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 30
Circuit Diagrams and PWB Layouts LC4.2E AA 7. 30 TV & Scaler Board: TV-Supply 1 2 3 4 5 6 7 8 9 TV-SUPPLY 11V9 A TO / FROM 1200 OF POWER SUPPLY UNIT F903 1910 1 2 3 4 5 6 7 8 9 10 11 12 F904 11V2 AUD-SUP 3V3 (1V2) +3V3STBY 14V4 +12VUNREG 2936 1n0 3V3 P-GND 5909 F905 A F914 11V6 F906 F907 F908 F909 F910 2937 1n0 2938 1n0 2939 1n0 2940 1n0 (0V) 3V3 (0V) 3V2 (3V3) 3V3 (3V3) 3V3 2941 1n0 2942 1n0 B 2909 330u F902 16V N.C.
PAGE 31
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 32
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 33
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 34
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 35
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 36
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 37
Circuit Diagrams and PWB Layouts TV & Scaler Board: Supply 1 2 3 LC4.2E AA 4 7. 37 5 6 7 8 9 10 11 12 SUPPLY FROM TV-BOARD SUPPLY A A +12VSW 2970 1n0 2964 1n0 +3V3STBY 5958 +12VUNREG POWER_DOWN B 2965 1n0 2968 1n0 2966 1n0 +12VSW A9 A7 BU_LIGHT_ADJ1 LAMP_ON-OFF 11V6 F958 2962 100n B 2969 1n0 PROVISION FOR 1.
PAGE 38
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 39
Circuit Diagrams and PWB Layouts LC4.2E AA 7. 39 Layout TV & Scaler Board: (Part 1 Top Side) Part 1 E_14490_019a.
PAGE 40
Circuit Diagrams and PWB Layouts LC4.2E AA 7. 40 Layout TV & Scaler Board: (Part 2 Top Side) Part 2 E_14490_019b.
PAGE 41
Circuit Diagrams and PWB Layouts LC4.2E AA 7. 41 Layout TV & Scaler Board: (Part 3 Top Side) Part 3 E_14490_019c.
PAGE 42
Circuit Diagrams and PWB Layouts LC4.2E AA 7. 42 Layout TV & Scaler Board: (Part 4 Top Side) Part 4 E_14490_019d.
PAGE 43
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 44
Circuit Diagrams and PWB Layouts LC4.2E AA 7. 44 Layout TV & Scaler Board: (Part 1 Bottom Side) Part 1 E_14490_020a.
PAGE 45
Circuit Diagrams and PWB Layouts LC4.2E AA 7. 45 Layout TV & Scaler Board: (Part 2 Bottom Side) Part 2 E_14490_020b.
PAGE 46
Circuit Diagrams and PWB Layouts LC4.2E AA 7. 46 Layout TV & Scaler Board: (Part 3 Bottom Side) Part 3 E_14490_020c.
PAGE 47
Circuit Diagrams and PWB Layouts LC4.2E AA 7. 47 Layout TV & Scaler Board: (Part 4 Bottom Side) Part 4 E_14490_020d.
PAGE 48
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 49
Circuit Diagrams and PWB Layouts LC4.2E AA 7. 49 Layout Side IO and LKB Panel (Top Side) Layout Side IO and LKB Panel (Bottom Side) 1301 1302 1303 1306 1307 1308 1309 1310 1311 1312 1313 A1 B1 B2 A2 A2 A2 A2 A2 B2 B2 A2 3139 123 5887.1 3139 123 5887.1 E_14490_025.eps 190404 E_14490_026.
PAGE 50
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 51
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 52
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 53
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 54
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 55
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 56
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 57
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 58
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 59
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 60
Circuit Diagrams and PWB Layouts LC4.2E AA 7.
PAGE 61
Circuit Diagrams and PWB Layouts LC4.2E AA 7. Layout Pixel Plus Panel (Top Side) Layout Pixel Plus Panel (Bottom Side) 1001 1002 1003 1100 2105 2136 2216 2419 2503 3112 3202 3406 3420 3424 5106 6403 7101 7201 7403 3122 123 6047.3 61 E_14490_091.eps 150704 D1 C1 A1 A1 C1 B1 C1 A1 D1 C1 C1 B1 D1 D1 B1 B1 B1 C1 A1 3122 123 6047.3 E_14490_092.
PAGE 62
Circuit Diagrams and PWB Layouts LC4.2E AA 7. 62 E_06532_013.
PAGE 63
Alignments LC4.2E AA 8. EN 63 8. Alignments General: The Service Default Mode (SDM) and Service Alignment Mode (SAM) are described in chapter 5. Menu navigation is done with the cursor Up, Down, Left or Right keys of the remote control transmitter. 8.1 8.2 There are no hardware alignments foreseen for the LCD-TV. 8.3 General Alignment Conditions Software Alignments With the software alignments of the Service Alignment Mode (SAM) the geometry, white tone and tuner (IF) can be aligned.
PAGE 64
EN 64 8.3.2 8. Alignments LC4.2E AA White Tone • In the White Tone sub menu the colour values for the colour temperature values can be changed. The colour temperature mode (Normal, Delta Cool, Delta Warm) or the colour (R, G, B) can be selected with the Right/ Left cursor keys. The mode or value can be changed with the Up/Down cursor keys. First the values for the Normal colour temperature should be selected. Range: 0-255, 128 represent the middle of the value (no offset difference).
PAGE 65
Alignments Sound EN 65 How to change an Option Byte An Option Byte represents a number of different options. Changing these bytes directly makes it possible to set all options very fast. All options are controlled via seven option bytes. Select the option byte (OP1.. OP7) with the Menu Up/ Down keys, and enter the new value. No adjustments needed for sound.
PAGE 66
EN 66 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets LC4.2E AA 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets • Index of this chapter 1. Introduction 2. Block Diagram 3. Power Supply 4. Input/Output 5. Tuner and IF 6. Video: TV Part 7. Video: Scaler Part 8. Audio Processing 9. Control 10. LCD Display 11. Abbreviation List 12. IC Data Sheets 9.1 • The architecture consists of a TV and Scaler panel, I/O panel, Side I/O and Local Keyboard panel and Power Supply panel.
PAGE 67
Circuit Descriptions, Abbreviation List, and IC Data Sheets The video part delivers the RGB signals to the Scaler IC. The Genesis GM1501 Malibu Scaler IC can receive two video input signals: SDTV (from Hercules), DVI (from external DVI source), or PC (from external computer). After the video processing, the digital data is send via a Low Voltage Differential Signalling bus to the LCD panel. LVDS is used to improve data speed and to reduce EMI significantly.
PAGE 68
EN 68 9.6 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets LC4.2E AA Video: TV Part (diagrams A1, A2, and A3) SYSTEM 7011 PAL-MULTI/SECAM A 4 NTSC +VTUN +5VSW TDA12021 TDA12001 TDA12011 CHINA/NTSC-AP 7011 - IF 7014 1328 7 VIF1 24 8 VIF2 25 CON RGB Matrix Blue & Black Stretch Gamma Corr. FM cvbs/y 3311 1 31 RF_AGC AGC Detect 1330 7 VSIF1 8 VSIF2 QSS Mixer/ AM Demod. 30 Dig. 2H/4H Combfilter Skin Tone U/V Tint Saturation Y Delay Adj.
PAGE 69
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC4.2E AA 9. EN 69 7011 7605 u-Processor 85 R_SDTV 86 G_SDTV 87 B_SDTV A2 H_CS_SDTV A2 V_SDTV 7604 13 14 1 HS 12 VS 2 1 2 3 4 H_CS 5 6 9 8 15 V 9,11 A7 SD_HD_SEL A2 R_SDTV 27 A2 G_SDTV 3 A2 B_SDTV 7 HERCULES IC 7530 7607 107 14 RED_PR V_SDTV EXT.
PAGE 70
EN 70 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets LC4.2E AA • – Sharpness meter • Contrast improvement • Gamma Look-Up Table All other picture improvement processing is done in the Scaler. • 9.9 Audio Processing For the case of NAFTA and LATAM, there is only one transmission standard, which is the M standard. The diversity then will be based on whether it has a dBx noise reduction or a Non-dBx (no dBx noise reduction).
PAGE 71
Circuit Descriptions, Abbreviation List, and IC Data Sheets • • • • E_14490_062.eps 020604 Figure 9-5 Micro Controller block diagram • • 9.10.3 Basic Specification The Micro Controller operates at the following supply voltages: • +3.3 V_dc at pins 4, 88, 94, and 109. • +1.8 V_dc at pins 93, 96, and 117. • I2C pull up supply: +3.3V_dc. • 9.10.4 Pin Configuration and Functionality The ports of the Micro Controller can be configured as follows: • A normal input port. • An input ADC port.
PAGE 72
EN 72 9. LC4.2E AA Resolution (HxV) Luminance Supplier Circuit Descriptions, Abbreviation List, and IC Data Sheets : LC230W01-A2K8 (23”) : LC260W01-A5K6 (26”) : 1080x768 pixels (17”) : 1280x768 pixels (23”) : 1280x768 pixels (26”) : 450 nit (17”) : 450 nit (23”) : 450 nit (26”) : LG.Philips LCD 9.
PAGE 73
Circuit Descriptions, Abbreviation List, and IC Data Sheets NVM O/C ON/OFF LED OSD P50 PAL PC PCB PIG PIP PLL Progressive Scan PWB RAM RC RC5 RGB RGBHV ROM SAM SIF SC SC1-OUT SC2-B-IN SC2-C-IN SC2-OUT S/C SCART SCL SD SDA SDRAM SECAM SIF SMPS SND SNDL-SC1-IN SNDL-SC1-OUT SNDL-SC2-IN SNDL-SC2-OUT SNDR-SC1-IN SNDR-SC1-OUT SNDR-SC2-IN SNDR-SC2-OUT SNDS-VL-OUT SNDS-VR-OUT SOPS Colour carrier NTSC M/N = 3.579545 MHz, NTSC 4.43 = 4.
PAGE 74
EN 74 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets LC4.2E AA 9.13 IC Data Sheets This section shows the internal block diagrams and pin layouts of ICs that are drawn as "black boxes" in the electrical diagrams (with the exception of "memory" and "logic" ICs). 9.13.
PAGE 75
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC4.2E AA 9. 9.13.2 Diagram A7, Type GM1501 (IC7401) Block Diagram 2-wire Serial I/F Parallel ROM IF/external micro JTAG GPIO Low Bandwidth ADC Pulse Width Modulator Internal ROM Internal RAM Clock Generation 14.
PAGE 76
EN 76 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets LC4.2E AA 9.13.
PAGE 77
Spare Parts List LC4.2E AA 10. EN 77 10. Spare Parts List Set Level Various 1099h 8301 8403h 8990 9322 194 30682 3139 131 03961 3139 131 03581 3139 131 03861 TFT-LCD LC230W01 FFC Foil 20P Cable 20P Cable 12P TV Scalerboard [A] Various 1001 1005 1302h 1303 1304 1328 1330 1401 1704 1910 8910 2422 543 01255 2422 025 18249 3139 147 19701 2422 025 16835 2422 025 16835 2422 549 44372 2422 549 44369 2422 543 01133 2422 025 16543 2422 025 16705 3139 110 28271 Crystal 24.
PAGE 78
EN 78 2617 2618 2619 2620 2621 2622 2623 2624 2625 2626 2630 2631 2632 2633 2634 2635 2636 2638 2639 2702 2703 2707 2708 2710 2711 2712 2713 2714 2715 2718 2719 2735 2736 2737 2738 2739 2740 2741 2742 2743 2744 2745 2746 2847 2848 2860 2861 2862 2863 2864 2865 2866 2867 2868 2869 2909 2910 2911 2920 2921 2930 2931 2933 2934 2935 2937 2938 2939 2940 2941 2942 2953 2955 2956 2957 2958 2959 2960 2961 2962 2964 2965 2966 2968 2969 2970 2992 2993 2994 2995 2996 10.
PAGE 79
Spare Parts List 3615 3616 3617 3618 3619 3620 3621 3622 3623 3624 3625 3626 3633 3634 3635 3640 3641 3642 3643 3644 3645 3646 3703 3706 3711 3712 3714 3715 3717 3718 3719 3722 3725 3726 3727 3730 3731 3732 3733 3735 3736 3737 3738 3739 3740 3741 3742 3743 3744 3745 3746 3747 3748 3749 3750 3751 3836 3838 3910 3911 3930 3931 3932 3933 3951 3952 3953 3954 3955 3958 4xxx 3198 031 02290 3198 031 02290 3198 031 02290 3198 031 02290 3198 031 08210 4822 117 13632 4822 117 13601 4822 117 13601 4822 117 13601 4822
PAGE 80
EN 80 10. LC4.
PAGE 81
Spare Parts List 2522 5322 126 11583 10nF 10% 50V 0603 f 3101 3102 3103 3104 3105 3106 3107 3108 3109 3110 3111 3112 3113 3114 3115 3116 3117 3118 3122 3125 3202 3204 3207 3210 3213 3216 3402 3403 3406 3407 3421 3510 3512 3513 3515 3519 3520 4822 051 30103 4822 051 30479 4822 051 30479 4822 051 30103 4822 051 30103 4822 051 30103 4822 051 30103 4822 051 30103 4822 051 30103 4822 051 30479 4822 051 30103 4822 051 30103 4822 051 30103 4822 051 30479 4822 051 30102 4822 051 30333 4822 051 30103 4822 051 303
PAGE 82
EN 82 11. LC4.2E AA Revision List 11. Revision List Manual xxxx xxx xxxx.0 • First release. Manual xxxx xxx xxxx.1 The manual is updated with information for models with Pixel Plus. This information is only applicable for xxPF9956 models. • Chapter: Mechanical Instructions, added Pixel Plus Panel removal instructios. • Chapter: Service Modes, Error Codes, and Fault Finding, some layout issues fixed. • Chapter: Block Diagrams, Testpoint Overvies, and Waveforms: Pixel Plus Panel added.