Register your product and get support at www.philips.com/welcome Installation Manual for xxHFL2819D/10 Status: Release Version 1.
Contents 1. Requirements before starting the installation.......................................................................................................... 2 2. Find out the state of the TV ...................................................................................................................................... 3 3. Re-install TV ..........................................................................................................................................................
1. Requirements before starting the installation Before starting the installation, make sure that you have everything you need at hand. Master remote control 22AV8573 or Guest remote control 22AV1407A And USB stick To enter the Hotel TV menu using the guest remote (22AV1407A): For all HFL2809 models you can use the guest remote and the key sequence 3,1,9,7,5,3,MUTE to access the Hotel Mode. The key sequence will not work if High Security Mode is enabled.
2. Find out the state of the TV It is important to know if a TV is in ‘virgin mode’ (out of the box) or installed before. If you can see this screen below, you know that the TV is in ‘virgin mode’ and you can install the set. See chapter 4 of this manual. If you power on the set and then press the ‘Home’ button on the guest remote, you will see this screen appear, if the TV already has been installed or the wizard was already skipped.
You can start the installation wizard again by reinstalling the TV as explained in chapter 3 of this manual. To be able to modify any settings on the TV you must disable the Hotel TV mode. Disable the Hotel TV mode To access the setup menu you should press the ‘RC5 SETUP’ key and then press the ‘Home/Menu’ button if you are using the 22AV8573. To access the Hotel TV menu using the guest remote you need to input the key sequence 3,1,9,7,5,3,MUTE .
3. Re-install TV If you want to start an installation from scratch you can always re-install the TV. First step is to set the Hotel Mode to OFF and exit using the MENU or Return button on the guest remote. Note: It is not required to use a save button, once you exit the menu, you will save the settings from the Hotel TV Menu Press the MENU button on the guest remote to access the full menu of the TV. The following menu should be displayed.
If you are sure that you want to re-install the TV, select “Yes” and press OK. TV will reboot itself and show the “virgin state” screens with a welcome message. Note: All settings will be reset to default values except Hotel menu values. Those values will remain the same. To reset the Hotel TV menu use the Reset to Default Values option present in that menu.
4. Installation wizard When you turn on the TV for the first time, or you have reinstalled the TV, you should see the following screen. The installation wizard, from whom this screen is a part, will guide you through all the menus for a basic TV installation. Please select your language and press “OK” to start the installation of the TV set. The first step is to select the country, which will enable country cable providers, time setting and channel list presets.
Depending on country you might need to follow an additional step, setting up a pin code. This pin code will be used for blocking TV channels and settings. In some cases due the country regulations, you have to provide a pin code formed from four digits. This pin code will be required in case you want to modify the settings of the TV. Selected PIN code cannot be 0000. Enter a PIN code and confirm it by entering it once more. Press the OK button to continue.
Aerial Installation If you select the AERIAL option in the Search Type screen, the TV set will search for digital terrestrial TV (DVB-T) broadcasts. NOTE: You can press the “MENU” button to cancel. After all the available stations are stored, the Channel List will be displayed on the screen. If you like to sort the channels according to the LCN (*), please select “Yes” and then press OK. Press the “MENU” button to quit the channel list and watch TV.
Note: If option Aerial & Cable option is selected, when DVB-T channel search is complete, you need to define the start frequency, end frequency and step for DVB-C channels. If you don’t know those values, use the default ones and press “OK” to start the search. When the automatic channel installation is complete, the following summary appears. Here you can move, edit or lock channels. The information bar displayed on the bottom part of the screen will guide you through the option that you are using.
Pressing the MENU button will bring the MENU with all options active. 5. Picture Accessing the picture submenu will bring the following menu on the screen: The option which can be set: - - Mode: Can be set to one of these options: Cinema, Game, Dynamic and Natural. Contrast: Sets the difference between the brightest and darkest of the screen. Brightness: Sets the brightness value for the screen. Sharpness: Sets the sharpness value for the objects displayed on the screen.
6. Sound The sound options are available from the main menu: Select and press “OK” to access the submenu: The options available are: - - Volume: Adjusts the volume level. Equalizer: In the equalizer menu, the preset can be changed to Music, Movie, Speech, Flat, Classic and User. Press the “MENU” button to return to the previous menu. The equalizer menu settings can be changed manually only when the Equalizer Mode is in “User” mode.
7. Settings The submenu can be access by pressing “OK” when this menu is highlighted. The options available are: - The Conditional Access: Controls conditional access modules when available. Language: Configures language settings (-may change depending on the country selected) Preferred and current settings will be available. - Parental: Configures parental settings including PIN code, Menu lock, Maturity Lock and Child Lock.
- Timers: Sets timers for selected programs. / Sets sleep timer to turn off the TV after a certain time. Date/Time: Sets date and time. Note:* The TV takes the time info via the broadcast. Correct time will be available on Date/Time Settings, if the time info is provided in the broadcast. If the TV is in no channel mode, Date/Time settings can be changed. However, if there is a channel preset, only “Time Settings Mode” can be changed and if this is set to Manual, Time Zone will be enabled.
The menu contains options for automatic channel install, manual channel install, network scan, analog fine tune for a better reception of the analog TV channels. The first time installation option will delete the TV channels and set all settings to default values, except Hotel TV settings. Automatic Channel Scan (Retune): Displays automatic tuning options available. Digital Aerial: Searches and stores aerial DVB-T channels. Digital Cable: Searches and stores cable DVB-C channels.
Manual Channel Scan: This feature can be used for direct broadcast entry. Search Type: Type of the channel to install Digital Cable, Digital Aerial or Analog Channel: The preset frequency Frequency: Input for the frequency Network scan: Enable or disable the network scan Signal quality & Signal Level These two options will show the quality and level of signal received on the frequency defined above. Network Channel Scan: Searches for the linked channels in the broadcast system.
First Time Installation: Deletes all stored channels and settings, resets the TV to factory settings and starts the first time installation. You can follow the instructions in the Initial Installation section for more information on this process.
8. Channel list For channels options like: reorder, rename or lock you have to access the menu from the picture below. Channel management can be also done with channel editor application available for PC. Check appendix 1 for channel editor installation and usage. Press “OK” for the submenu. Note: If the following menu is not displayed in the menu, please go and disable the Hotel TV mode. Edit channel list: The channel list with all TV channels installed will be displayed.
With the up and down arrow buttons you can select the channel and with the left and right arrow buttons the function which will be used for that channel. To move a TV channel in the list you need to do something similar. Select the TV channel with the up or down arrow buttons, and then select the Move function and press “OK”. The TV will display a new window in which you must enter the new position of the channel. The channel plan will be updated after you press “OK”.
Export Channel list to USB: This option will export the channel to USB. The exported channel plan can managed on PC using Channel Editor Application. See appendix 1. Note: The USB drive must be format FAT32. Import Channel list to USB: This option will import the channel plan from USB. Make sure that only channel plans managed with Channel Editor are imported from USB. 9. Media Browser You can play photo, music, and movie files stored on a USB disk by connecting it to your TV.
10. Professional Settings [Hotel Mode] Feature to enable or disable the Hotel TV Menu features. Note: When enabled, the TV will follow configured feature settings. If the Hotel Mode is set to OFF, none of the settings from this menu will be active. [Pin8] Feature to enable or disable the auto SCART feature Note: This feature allows a connected SCART device to turn the TV on or off. [Last status] This feature allows the TV to remember the last used configuration and restore when startup again.
[Startup Position] Select startup program/source when TV is switched on via Power On key or Digit keys. • Auto TV wakes up in last used channel/source. • TV: The TV set wakes up with the channel specified in Startup Channel field • SCART / Side AV / HDMI1/ YPbPr / VGA_PC [Startup Channel] Feature to select the startup channel. [Volume Limit] Feature to set the maximum volume level. Selectable values between 0-63.
[OSD Disable] Feature to hide menu items when the Remote Control Menu key is pressed. • Disable All Menus :all menu icons are hidden • Disable Setup Menus: Picture, sound, settings and media browser menu icons are displayed. When [Hotel Mode] is set to Off, all TV menu items will be displayed (picture, sound, settings install and retune, channel list, media browser). If OSD Disable is set to Disable All Menus, the EPG will not be displayed. [Teletext] Feature to hide the Teletext display.
[USB option] Feature to detect if a USB device is connected. • On: to enable USB device detection. • Off: to disable USB device detection. When [Off] the Media Browser icon will be displayed but cannot be activated. [Fixed Pic. Mode] Feature to hide the picture menu icon • Off: picture icon is displayed amongst all menus. • On: picture icon is hidden [Digital Tuner] • Off: mixture of analog and digital channels • On: digital channels only [Multiple RC support] Feature to enable the Multi RC.
[High Security] If you set this option as ON, the Hotel TV menu will be accessible only with Philips master remote control. [Reset to Default Values] Highlight this option and press the OK button on the remote to return the TV to default settings. Note: Only Hotel TV options will be affected by this action. TV channels will not be deleted. [EPG Enabled/Disable] Enabling this option will make EPG available when Hotel TV mode is active.
11. Welcome Logo Once this feature is configured and set, the welcome image will be displayed within 8 seconds after switch on. This page will remain until a key on the RC is pressed. How to upload Welcome Logo 1. Create a graphics file: 960 x 540.png with the logo. Follow the next guidelines: Maximum size of the welcome logo should be less than 1024 Kb. Always use 16 bit color depth. 2. File name: hotel_wel.png (File name is case-sensitive) 3. Create a folder named “welcome_image” on your USB key. 4.
12. Clone With cloning it is possible to copy to/from a USB device the configuration data and the channel list data from a TV. Place a USB Memory stick in the USB side connector of the TV. *The USB device should be formatted as FAT or FAT32. Access the Hotel Mode Menu with the RC 8573 (yellow remote) or with the guest remote by entering the key sequence 3,1,9,7,5,3,MUTE and navigate with the TV remote to following items: [Copy from USB] 1. Select [Copy from USB] and press OK. 2.
13. Feature settings [Multi RC] Enter the MultiRC Menu Feature to configure the remote control to work with one TV. To enter the MultiRC Menu on TV press the key sequence: MENU, RETURN, 1,2,3,4. On the TV a menu will guide you to select the desired TV configuration. Choose a number between 1 and 4 to assign to the TV. Afterwards configure the remote control for the same number as TV by keeping pressed MENU (HOME)+Digit for 5 seconds. The HFL2809 supports a maximum value of four remotes.
14. CSM (Consumer Setup menu) Enter Service Menu It is only possible to enter the Service Menu if the Hotel Mode is disabled. Enter the Hotel Mode menu and set the Hotel Mode to “Off” To enter the Service Menu: • Press the following key sequence: Menu, 1,2,3,6,5,4 No items can be selected in the Service Menu. The software version number will show as VES141HE_x.y.
Appendix 1 Channel List Editor Channel List Editor PC tool enables editing exported XML channel list files in a way that is more understandable and user friendly. Note: XML means Extensible Markup Language Channel list should be exported from a TV set using the option available in the following menu (make sure that Hotel mode is set to OFF): 1. 2. 3. 4. Insert the USB key on side connector of the TV. Enter in the MENU and navigate to Channel list. Select the option “Export Channel list to USB”.
Interface description and usage 1. Main window Main menu consists of pretty much the same options as the toolbar below, with exception of “Save as” and “Exit” option from File submenu. File submenu consists of standard options as it can be seen on ion the Image 1-1 – File Image 1-1 – File Edit submenu consists of controls to Add, Edit and Delete the current selected channels in the list. Image 1-2 – Edit Tools submenu consists of Settings and Preferences ( Image 1-2- Tools).
First group from the left provides file operations next to it provides channel managing operations and the last group provides list settings and help. Image 1-3 – Toolbar Clone – clones channel info except for Service name and service number for easy adding channel with similar values. Under tool bar there is a list of channels from the loaded list sorted by network type in a tree view. More than one channel can be selected by holding SHIFT or CTRL and right mouse click.
Image 1-6 - Common Service Params And, depending on the Network Type of the currently selected channel, different additional groups can be displayed: Image 1-7 - DVB Triplet Values in DVB Triplet are only present when DVB channels are selected, for Analogue channels values in this group are empty. Image 1-9 - DVB-C When the form is in add/edit state new buttons are added under “Tuner Configuration” group: Image 0-8 - Edit state 2.
Image 2-1 - Add Add – changes the state of the main form to add state and empty’s all the fields so the user can enter new values. Only when in add state Network Type combo box is enabled. When correct values are entered user can save with pressing “Enter” key or pressing “Add” button. Image 2-2 – Clone Clone - is much like Add just instead of leaving all the fields empty it leaves all the values from the previously selected channel except for values that needs to be unique (Service Name, Channel Number...
Image 2-3 – Edit Edit – enables editing of the currently selected channel info. When correct values are entered user can save with pressing “Enter” key or pressing “Save” button. Channel or selection of channels can be moved using drag and drop. Move will cause renumbering of the channels in the list. Delete – removes the channel from the list. When single service channel is selected on delete message appears asking the user to confirm deletion of the channel with the corresponding name.
Channel number or LCN can take values from 1 – 9999 as it is defined in code. These limitations are applied in the editor. Save – when the channel list is according with the requirements press “Save” button for saving the channel list. This option will rewrite the open file and save it in the same location. If you want to save the file in to another location please use the “Save As” option from File menu. 3.
© 2014 Koninklijke Philips N.V. All Rights reserved. Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips N.V. or their respective owners. www.philips.
