Assembly Manual 6x5 CAUTION Sharp Edges PATENTS ARE PENDING Building Dimensions Approximate Size Storage Area Sq. Ft. Exterior Dimensions Interior Dimensions Roof Edge to Roof Edge Wall to Wall 6’ x 5’ 24.75 Cu. Ft. 140.25 Width 69.75” Depth 62” Height 72” Width 66” 1.8 m x 1.5 m 2.30 m2 3.97 m3 177.17 cm 157.48 cm 182.88 cm 167.64 cm 712570303 Depth 54” 137.16 cm Height 71” 180.
1 Before You Begin Site Preparation BASIC TOOLS 1. Before beginning construction, check local building codes regarding footings, location and other requirements. Study and understand this owner’s manual. CAUTION No. 2 Phillips 2. Follow all directions and dimensions carefully. Work Pliers Sharp Screwdriver 3. Follow the step sequence carefully for correct results. Gloves Edges 4. Be sure all the parts fit together properly before proceeding. 5.
Care & Maintenance Finish: For long lasting finish, periodically clean and wax the exterior surface. Touch up scratches as soon as you notice them on your building. Immediately clean the area with a wire brush; wash it and apply touch up paint per manufacturer’s recommendation. Roof: Keep roof clean of leaves and snow with long handled, soft bristled broom. Heavy amounts of snow on roof can damage the building making it unsafe to enter. Doors: Keep doors closed to prevent wind damage.
3 Step 1 Pre-Assembly Part No Side Walls 10307 10268 Name Wall Panel Corner Panel Quantity 8 2 ASSEMBLY COMMON FOR ALL PANELS MAKE TWO (2) SIDE WALL SECTIONS 4 Panels & 1 Corner - Each A ARROW TO TOP IMPORTANT MUST USE FLAT SOLID SURFACE DO NOT SNAP ON GROUND OR GRASS! CAUTION Sharp Edges B 1 2 C Raise Panel at Angle NOTE: ALWAYS COVER THE ARROW! Overlap Panels and align ends Hook edge of top Panel to bottom Panel
Pre-Assembly D Side Walls . . . .
5 Pre-Assembly H Side Walls. . . .
Pre-Assembly Side Walls. . . .
7 Pre-Assembly Part No Side Walls . . . .cont 10255 10280 M Name Floor Channel (unpainted) Corner Clip Quantity 2 4 Insert Corner Clip M Insert Corner Clip Floor Channel is Unpainted L Attach Floor Channel in the same sequence as Upper Channel.
Step 2 A Pre-Assembly Rear Wall 2 Part No Name 10307 10268 Wall Panel Corner Panel Quantity 5 1 MAKE ONE (1) REAR WALL SECTION CAUTION Sharp Edges 5 Panels and 1 Corner ARROW TO TOP IMPORTANT MUST USE FLAT SOLID SURFACE DO NOT SNAP ON GROUND OR GRASS! ARROW TO TOP B Install Corner Panel 8
9 Pre-Assembly C Rear Wall . . . .
Step 3 A Pre-Assembly Front Wall Part No 2 Assemble Door Jambs to Wall Panels Install Bolt, Washer & Nut in each Door Jamb 10316 10317 10373 10268 Name Wall Panel -Right Wall Panel - Left Door Jamb Corner Panel Quantity 1 1 2 1 2 Door Jambs always on top of Panel ARROW TO TOP 10316 10317 B Install Corner Panel Wall Panel on top of Corner Panel CAUTION Sharp Edges 10
11 Pre-Assembly Front Wall . . . .
Step 4 Wall Assembly Part No 2 Name Quantity Side Wall Assembly Rear Wall Assembly 1 1 Install Corner Clip CORNER PANEL ON TOP OF WALL PANEL Corner Clip Corner Panel B Upper 1 Side Panel 2 Make Sure Engaged Install Corner Clip A Lower 3 1 2 Make Sure Engaged CAUTION 3 Sharp Edges 12
13 Wall Assembly . . . .
Part No Step 5 Gable & Ridge Beam Assembly A Snap Gables onto Upper Channel 2 10265 10266 10258 10278 Name Left Gable Right Gable Header Angle Gable Brace Quantity 2 2 1 2 8 4 2 1 Gable B Assemble Header Angle Upper Channel Header Angle C Install Gable Braces onto Gables Header Trim CAUTION Sharp Edges 14
15 Gable & Ridge Beam Assembly . . . .
Part No Step 6 Pre-assembly - Roof 2 MAKE TWO (2) ROOF SECTIONS A Align Roof Panels and snap panel ribs together 10252 10250 10251 10267 10320 Name Roof Panel Roof Panel-Right Roof Panel-Left Roof Channel Roof Fascia Quantity 6 2 2 4 4 HOLES 10252 10252 8 10250 ARROW TO TOP 10252 10251 HOLES NOTE Large Holes on Channels FACE DOWN B 10250 Assemble Roof Channel onto top and bottom CAUTION Sharp Edges 10251 C Assemble Fascia Trim onto each side 10250 10251 16
17 Step 7 Roof Assembly D Part No Name 10270 Ridge Cap 2 Quantity 1 10 Assemble Left Roof Section to building NOTE HOLE POSITIONS CAUTION E Install Ridge Cap on Right Roof Section Sharp Edges
Roof Assembly. . . .
19 Step 8 Door Assembly A Part No 2 Name Quantity 10361 Vertical Door Brace 10369 Vertical Door Brace Handle 1 1 1 Part No Name Padlock Eyelet Clip Quantity 1 4 4 Slide Clips onto Verticle Door Brace Installing Clips 1 CORRECT! INCORRECT! 10361 2 B Attach Door Handle & Padlock Eyelet to Vertical Door Brace CAUTION Sharp Edges 10369
Door Assembly . . . .
21 Door Assembly . . . .
Door Assembly . . . .
23 Step 9 Anchor Building It is important that building be anchored after construction. These are recommended ways of anchoring. 2 Anchor Kit Model No AK4, SAK4 or 60298 Recommended for use with any suggested base. Contains 4 Anchors with Cable, clamps and installation instructions. Anchor Kit Model No AK100, SAK100 or 68383 Recommended for use with concrete foundation. Contains corner gussets, perimeter clips, hardware, 1/4” masonry drill bit and installation instructions. 13” (33.
Parts List 6x5 Dia. No. Part Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Wall Panel Wall Panel - Right Wall Panel - Left Corner Panel Upper Channel (painted) Floor Channel (unpainted) Upper Channel (painted) Floor Channel (unpainted) Door Jamb Header Trim Ramp Corner Clip Left Gable Right Gable Header Angle Gable Braces Ridge Beam Ridge Beam Angle Roof Panel Qty Part No. Dia. No.
25 26 6x5 19 26 5 4 1 1 4 10 13 20 1 1 26 19 22 26 12 4 5 14 15 12 1 8 12 6 32 4 1 2 9 1 12 8 23 19 23 1 16 3 11 22 19 17 13 7 1 18 1 1 22 21 24 25 14 7 19 21 16 12 1 25 20 19 23 12 23 22 31 1 9 12 30 33 6 33 12 27 29 32 28
