Instructions / Assembly

READILY ADAPTS TO ANY
SIZE PERMAFLOAT® FLOAT
DRUM!
L
G
H
I
K
J
A
D
E
F
B
C
Outside Corner (Female) - has two
1/2" welded tabs. Use with a male out-
side corner. Each leg is 10"L x 5"H.
RHH-OCF WT 9.0
l Outside Corner (male) - has one 1/2"
welded tab. Use with a female outside
corner to connect docks end to end. Joint
requires 3/4" bolt set or connector pin (L).
Each leg is 10"L x5"H.
RHH-OCM WT 8.5
l Outside Corner End - use this corner
at ends of fingers and docks. Ideal for
swim floats and ski jump corners. Each
leg is 10"L x 5"H.
RHH-OCE WT 7.0
l Inside Corner - this heavy-duty inside
corner should be used with one of the
outside corners. Each leg has elongated
holes for easy fit-up and is 8-1/4"L x 6"H
RHH-IC WT 6.5
l Inside Corner/Pipe Holder 3" - these
heavy-duty inside corners should be
used with one of the outside corners and
has an internal pipe holder to be used
with 2" pipe. Welded gusset gives
strength to the dock’s frame. Measures 8-
1/4"L x 5"H. Requires carriage bolt set for
attaching
RHH-O1C3 WT 11.5
l Angle - use this heavy-duty angle for
all cross supports. Each leg measures 2-
1/2"L x 5"H.
RHH-A WT 1.75
l Female T Connector - has two
welded 1/2" tabs. Bolts to side of dock to
attach fingers and ramps. 5"L x 5"H.
RHH-SF WT 3.5
l Male T Connector - has one welded
1/2" tab. Use with female T connector to
attach fingers and ramps. 5"L x 5"H.
3/4" bolt set required for joint.
RHH-SM WT 3.25
l Washer Plate - use two washer plates
with each angle. Measures 1-1/2"L x5"H.
RHHW WT 0.5
l Chain Retainer - bolts to side of dock.
Use weights and chains to hold dock in
place. Accommodates 1/4", 3/8", & 1/2"
chain. Measures 5"L x 5"H.
RHCH WT 3.75
l Pipe Holder/Outside 3" - bolts to out-
side of dock. Carriage bolt set required
for attaching. Use 2" pipe to hold dock in
place.
RHP-3 WT 8.25
l Connector Pin Set - for quick discon-
nect. Used to connect male and female
connectors. Galvanized 3/4" connector
pin and hitch clip pin.
RHBPIN
Cellofoams’ Dock Hardware is de-
signed for use with 1-1/2" thick lumber
(minimum width 6'). All hardware is
mounted with 1/2" carriage bolts. All male
and female dock to dock connections are
made with either 3/4" bolts with lock nuts
or 3/4" connecting pins (L).
B
C
D
E
F
G
H
I
J
K
L
For orders and customer
service requests, contact us at
800-531-4734
[e-mail]
www.cellofoam.com
Copyright © 2018 Cellofoam North America Inc.
All rights reserved. Printed in USA. PermaFloat,
PermaLaunch, and PermaPort are registered
trademarks of Cellofoam North America Inc.,
Conyers, GA.
A
DOCK HARDWARE
Galvanized Structural Steel