INSTALLATION VIDEO Extra Wide Retractable Gate INSTRUCTION MANUAL White #755 Grey #2741 Warm Black #2725 Black #2739 Timber #2701 33cm - 180cm 84cm FITS OPENINGS TALL (13” - 71”) (33”) IMPORTANT! READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE.
TABLE OF CONTENTS SAFETY INFORMATION General Maintenance Warnings Mountings / Tools Required 03 03 04-05 06-07 WHAT’S IN THE BOX Parts 08-09 INSTALLATION Gate Placement With Skirting or Baseboard Inside Opening or Doorway Outside Opening or Doorway To Attach / To Remove 10 11 12-13 14 15 OPERATION How to Open Cleaning Instructions 16 17 SUPPORT Warranty Certificate Warranty Card After Sales Support 18 19 19 02
SAFETY INFORMATION GENERAL Read this instruction manual carefully and keep it in a safe place for future reference. The correct use and maintenance of this product is essential. MAINTENANCE Regularly check that the gate is functioning correctly, lubricate hinges and moving components. Tighten and adjust mounts to ensure secure smooth operation. Inspect all components regularly and stop using if any component is damaged or missing. Refer to pages 16 & 17 for operation and cleaning instructions.
WARNING • To prevent serious injury or death, securely install gate or enclosure and use according to manufacturer instructions. • Incorrect installation can be dangerous. • Danger to older children if climbing over the product. • Discontinue the use of the safety barrier if it becomes damaged, broken or disassembled. • The safety barrier must not be fitted across windows. • Never install this product on glass doors. Install this product against reliable doors or walls.
WARNING • Always check that the safety barrier is correctly closed. • Use only with the locking / latching mechanism securely engaged. • Gate must be installed as close to the ground as possible, as per the installation guides. • Never use with a child able to climb over or dislodge / open the gate or enclosure. • Regularly check that the safety barrier is properly installed and secure. • ALWAYS install and use gates / enclosures as directed, using all required parts.
SAFETY INFORMATION MOUNTINGS Gate must be installed in a structurally sound opening. Ensure mounting surface (wall, door, stair posts, etc.) is strong, rigid and has an even surface. Note: If the safety barrier is used at the top of the stairs, it should not be positioned below the top level. If the safety barrier is used at the bottom of the stairs, it should be positioned at the front of the lowest tread possible. This gate must only be fixed to a solid and secure surface.
SAFETY INFORMATION Select the appropriate fixing method from the list below. HARD WALL MOUNTING BRICK / CONCRETE FOR INSTALLATION Wood Screws Anchor 1. Drill 5mm (3/16”) Pilot Hole 2. Clear Hole 3. Insert Anchor & Tap 4. Tighten slowly WOOD MOUNTING FOR INSTALLATION Wood Screws 1. Drill 2mm (5/65”) Pilot Hole 2. Clear Hole 3. Insert Screw 4. Tighten slowly DRY WALL MOUNTING Locate the wood stud and follow the wood mounting instructions. Do not mount into dry wall without additional support. 1.
WHAT’S IN THE BOX PARTS 1 x Gate Assembly 1 x Gate Mount Installation Guide 1 x Catch Installation Guide 08
WHAT’S IN THE BOX 1 x Upper Gate Mount 1 x Lower Gate Mount 6 x Wall Spacers 2 x Catch Mounts 8 x Wall Plugs 4 x 35mm (1 3/8”) Upper Mount Screws (use with spacers) 09 4 x 25mm (1”) Lower Mount Screws
INSTALLATION Gate Placement Suitable placement of Gate and Catch Mount INSIDE OPENING OR DOORWAY OUTSIDE OPENING OR DOORWAY 10
INSTALLATION Skirting or Baseboard To help correct for the offset of the skirting board or baseboard, Spacers will be required. Measure the width of your skirting / baseboard and use the closest number of Spacers to fit this width. Each Spacer is 5mm (3/16”) thick. NOTE: Only use spacers for the Upper Gate Mount and the Upper Catch Mount. 5mm (3/16”) Align Spacers and Mounts in their correct position and use a phillips screw driver to tighten Screws until each Mount is secure.
INSTALLATION Step 1. Inside Opening or Doorway Hold guides vertically and completely outstretched against mounting surface with the end marked “FLOOR” even with the floor. Mark screw hole positions. Remove templates. NOTE: Leave at least 20mm (3/4”) between Guide and the edge of the opening to ensure gate won’t overhang edge.
INSTALLATION Step 2. Step 3. Align the Upper & Lower Gate Mount on the side you want the gate to extend from. Tighten Screws until each Mount is secure. Align the Catch Mounts in their correct position on the side you want the gate to extend. Tighten Screws until each Mount is secure. NOTE: These holes must be used to mount inside an opening or doorway. NOTE: Ensure Lower Catch Mount has locking groove.
INSTALLATION Step 3. Outside Opening or Doorway Follow Steps 1 & 2 from “Installation Inside Doorway or Opening” on pages 12 & 13. Align each Mount in their correct position. Tighten Screws until each Mount is secure. NOTE: These holes must be used to mount outside an opening or doorway.
INSTALLATION To Attach Attach Gate Assembly to the Gate Mounts by aligning the gate SLIDE directly above and sliding straight down over Mounts. The gate will lock in place with a “Click”. Check that the Assembly is flush against the wall and is locked firmly in place. “CLICK” To Remove To remove gate from the PUSH + HOLD Mounts, push and hold the release button while sliding the gate upwards.
OPERATION HOW TO OPEN 1. Push To unlock the mechanism simply push down. 2. Twist + Release While still pushing down, turn the button clockwise. Then release. 3. Pull Pull handle in one fluid movement as stopping will engage lock. Hook onto Catch Mounts to secure. ONE HANDED OPERATION NOTE: When gate is retracting always hold the handle and guide the gate evenly back into its original position. Never let go of the handle when gate is retracting.
CLEANING INSTRUCTIONS Simply use a soft damp cloth to wipe gate, dry after cleaning. Do not use chemical or abrasive cleaners.
SUPPORT WARRANTY CERTIFICATE Congratulations! You have made an excellent choice of this quality product. Our commitment to quality also includes our service. Should you, contrary to expectations, experience defects due to manufacturing faults, we will provide you with a warranty against defects as follows: WARRANTY The product is guaranteed to be free from from defects in workmanship and parts for a period of 12 months from the date of purchase.
SUPPORT WARRANTY CARD DETAILS: PRODUCT NAME: Extra Wide Retractable Gate PRODUCT NUMBER: White 755 / Grey 2741 / Black 2739 / Warm Black 2725 / Timber 2701 YOUR NAME: ADDRESS: PHONE: EMAIL: DATE OF PURCHASE: LOCATION OF PURCHASE: We recommend that you keep a copy of your receipt, showing the date of purchase, with this warranty certificate and keep for your reference. In the event of a product fault, please contact after sales support.
Scan the QR code for Live Chat Support or visit: permachildsafety.