WHOLE HOUSE WATER FILTER SYSTEM PC600-P | PC1000-P pentair.
TABLE OF CONTENTS PRODUCT OPERATION AND SPECIFICATIONS ......................................................................................................................... 3 COMPLETE PARTS LIST.......................................................................................................................................................... 3 INSTALLATION OVERVIEW........................................................................................................................................
PRODUCT OPERATION AND SPECIFICATIONS Specification Description PC600-P PC1000-P Rated Service Flow Rate 8 GPM 12 GPM Peak Flow Rate 12 GPM 16 GPM Minimum Working Pressure 25 PSI Maximum Working Pressure 80 PSI Maximum Vacuum 5 inch/127 mm Hg Operating Temperatures 36˚F – 120˚F pH Range 6-11 COMPLETE PARTS LIST Note The parts supplied are intended to accommodate a variety of water supply lines. Additional fittings may be needed to fit to your plumbing. Visit pentair.
INSTALLATION OVERVIEW Wall Wall Wall Outgoing Water to House Sediment Filter 19” Sediment Filter Outgoing Water to House 19” Incoming Water Supply OUT IN IN Incoming Water Supply OUT Wall Top View Top View Carbon Water Filter System Bypass Carbon Water Filter System Bypass Water to Home Shut Off Valves Shut Off Valves Water to Home Sediment Filter Sediment Filter Water Filter Water Filter Front View Front View Note Sediment filter position is at the discretion of your profession
PRE-INSTALLATION Note Head may come loose in transit. Please check head by tightening clock wise, hand tighten only, no more than 1/4 turn. Head may not move at all or less than 1/4 turn. Bypass Valve Installation Red Arrow T Quick Connect Nut INLET Water Filter Head OUTLET Top View Carbon Water Filter System Figure 2 The bypass valve comes pre-assembled and ready to install with the o-rings, split rings, and quick connect nuts.
MEDIA SOAK Wall IN OUT Wall Incoming Water Supply Outgoing Water to House Sediment Filter Top View Carbon Water Filter System Bypass Carbon Soak/Rinse Note Steps 1-3 should be done prior to installation 1. Locate the carbon filter tank and the hose bib attachment. 2. Attach the hose bib attachment to “Inlet” side of the carbon filter. Attach garden hose to the hose bib and turn water slowly until water flows out of the outlet of the tank (a stream of water about the size of a pencil).
SEDIMENT FILTER INSTALLATION Note Sediment filter position is at the discretion of your professional installer. As a general guideline, the sediment pre filter is typically installed in the "pre" position (as shown above) for well-water applications. For city water applications, the sediment filter is typically installed in the "post" position after the Carbon Water Filter System Tank. Sediment Filter Sediment Filter Cover O-Ring x2 Blue Filter Housing Stand Pipe Part 1 1.
CARBON WATER FILTER SYSTEM TANK INSTALLATION 1. Level the Carbon Water Filter System Tank. WATER SOFTENER ALTERNATIVE TANK INSTALLATION Note See "Troubleshooting" section on tips for leveling the tank. If the tank is not level, lift the tank straight up 6 inches and tap it on the ground until the tank stands vertical. The bottom of the tank is round and the boot allows the tank to stand upright.
BYPASS VALVE OPERATIONS Service InInService Figure A shows the system "in service" which allows water to flow in and out of the tank. In this position the system would be considered ON. Figure A Figure A In Bypass In Bypass Figure B shows the system "in bypass" which will direct water straight to the home without going in and out of the tank. In this position the system would be considered OFF. Figure B Figure B COMPLETE THE INSTALLATION 1. Turn on main water supply and check for leaks. 2.
MAINTENANCE Media Replacement Your Pentair® PC600-P / PC1000-P Premium Whole House Water Filter requires care and cleaning after a period of 5 years. Replacement media and instructions can be ordered on-line at Pentair.com/homewater or by calling 877-842-1635. Model numbers for replacement media are PC600-R or PC1000-R. Sediment Filter It is recommended that the sediment filter be replaced every 6-9 months depending on the amount of sediment present in the water supply.
TROUBLESHOOTING Problem Solution Water leaking at the top of the tank around the head. You may need to turn the head to tighten it. The tank head is pre-installed hand-tight, do not overtighten the head (just turn it snug). The tank leans to one side or is not level. If the tank is not level, lift the tank straight up 6 inches and tap it on the ground until the tank stands vertical. The bottom of the tank is round and the boot allows the tank to stand upright.
PRODUCT WARRANTY AND REGISTRATION FORM For details on your Pentair product warranty, please visit Warranty Registration Form Send in this Warranty Registration Form to validate your warranty or visit pentair.com/register-warranty to complete the warranty registration form online. Date Item(s) were Received: Order ID#: Model: Dealer Purchased From: Model/Serial Number: Name: Address: City: State: Zip: Send to: Pentair 2361 Mason Avenue, Suite 100 Daytona Beach, FL 32117 Phone: 1.800.842.
PRODUCT CERTIFICATION Certified By IAPMO R&T to NSF/ANSI Standard 42 for the reduction of Chlorine Taste & Odor, structural integrity & NSF/ANSI 61 for material safety. The NaturSoft® system is DVGW DW-9191 certified for 99.6% hard water scale prevention.
• WHOLE HOUSE WATER FILTER SYSTEM
WHOLE HOUSE WATER FILTER SYSTEM • 15
2361 Mason Ave | Suite 100 | Daytona Beach, FL 32117 | United States P: 877.842.1635 | Technical Services: 877.842.1635 | pentair.com/homewater © 2021 Pentair. All indicated Pentair trademarks and logos are property of Pentair. Third party registered and unregistered trademarks and logos are the property of their respective owners.
