52” BROOKEVILLE CEILING FAN Owner’s Manual Models #20679 (355-0645) If a problem cannot be remedied or you are experiencing difficulty with installation, please contact the Service Department: 1-877-459-3267, 9 a.m.- 5 p.m. Central time.
PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: 1 PACKAGE CONTENTS 2 3 4 5 6 7 8 9 10 1. Canopy 12. Motor Screw (x10) 2. Canopy Cover 13. Fitter Plate 3. Yoke Cover 14. Fitter Plate Screw (x3) 4. Mounting Bracket Screw (x4) 15. Light Kit 5. Mounting Bracket 17. Finial 6. Downrod 22 18. Glass Bowl 7. Downrod Pin 8. Downrod Clip 11 9. Set Screw (x2) 12 13 19 18 14 16. Finial Cap 10. Closemount Screw (x3) 11. Motor Assembly 19.
DIMENSION REFERENCE C B A A. 16.48 in. B. 11.34 in. C. 5.13 in. MOUNTING OPTIONS Three Mounting Options Closemount Downrod Mount Angled Ceiling Mount (Up to 16 degrees) Choose one of the following mounting options: Closemount method is best suited for ceilings lower than 8 feet. It does not utilize the downrod. Downrod Mount is best suited for ceilings 8 ft. or higher. For taller ceilings you may want to use a longer downrod (not included).
SAFETY INSTRUCTIONS READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN AND SAVE INSTRUCTIONS. CAUTION: All set screws of the fan must be checked and retightened where necessary before installation. To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades or cleaning fan. Do not insert foreign objects in between rotating fan blades.
ASSEMBLY INSTRUCTIONS 1. Turn OFF the electrical power at the main fuse or circuit breaker. 1 Mounting Bracket Screw 2. Loosen all four preassembled mounting bracket screws, then completely remove the two mounting bracket screws from the round holes of canopy. Set aside for later use. 2 D CAUTION: It is very important to use the proper hardware when installing the mounting bracket as this will support the fan. 3. Remove the ten motor screws from the underside of the motor assembly.
ASSEMBLY INSTRUCTIONS 5. Insert the downrod through the canopy and yoke cover. Feed the wires from the fan through the downrod. Canopy Yoke Cover Downrod 5 6. Slide the downrod into the yoke of the motor assembly, align the holes, then re-install the downrod pin and downrod clip. Secure with set screws and slide the yoke cover down until it rests on top of the motor assembly. Downrod Yoke Cover Downrod Clip Downrod Pin Set Screw 6 8 in. 7 7.
ASSEMBLY INSTRUCTIONS 9. Install the downrod into the opening of the mounting bracket. Align the slot in the downrod with the tab on the mounting bracket. The downrod should not rotate in the mounting bracket if installed properly. Slot Downrod Tab Mounting Bracket Downrod Clip Downrod Pin 9 Black (hot) White (neutral) Green White Black Blue Bare/Green (ground) 10 Warning: Do NOT use a full-range dimmer switch to control the fan speed.
ASSEMBLY INSTRUCTIONS 13. Install the blade arm to the underside of the motor assembly with previously removed motor screws. Tighten each blade arm completely before moving to the next. 13 Blade Arm Motor Screws Fitter Plate Screw 14. Remove the three fitter plate screws from the fitter plate. Connect the 9-pin connector from the fan to the 9-pin connector from the light kit. 9-Pin Connector 14 Light Kit 15.
ASSEMBLY INSTRUCTIONS Light Kit Pull Chain Finial Cap Glass Bowl 17 17. Feed the pull chains through the appropriate holes in the glass bowl, finial cap and finial. Lift the center hole in the glass bowl over the threaded rod of the light kit. Then, lift the finial cap up until it is flush with the glass bowl and secure with finial. Finial 18. Attach pull chain extensions to the pull chains. 18 Pull Chain Extention 19. Turn on the circuit breakers and the wall switch to the fan supply lead lines.
OPERATING INSTRUCTIONS 1 Light Pull Chain 1. The fan pull chain is located in the off-center hole in the finial cap. It has four positions to control fan speed. One pull is HIGH, two is MEDIUM, three is LOW and four turns the fan OFF. The light pull chain is located in the center of the finial. It turns the light ON and OFF. Fan Pull Chain 2. Use the reverse switch, located on the light kit to optimize your fan for seasonal performance.
TROUBLESHOOTING If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check the Troubleshooting section below. If a problem cannot be remedied or you are experiencing difficulty in installation, please contact the Service Department: 1-877-459-3267, 9 a.m.- 5 p.m. Central time. PROBLEM SUGGESTED REMEDY 1. Fan does not start 1.
LIMITED LIFETIME WARRANTY To obtain Service, please contact the Service Department: 1-877-459-3267, 9 a.m.- 5 p.m. Central time.
