Model No.
Package Contents: 1 2 3 4 7 6 5 9 8 10 11 12 13 14 15 Unpack your fan and check the contents. You should have the following items. 1.) Hanger Bracket 2.) Canopy 3.) Canopy Cover (Preassembled to Canopy) 4.) Downrod Set (Included Hanger Ball, 6” Downrod, Hanger Pin & Lock Pin) 5.) Downrod Stand Cover 6.) Fan Blade (5 PCS) 7.) Fan Motor Assembly 8.) Blade bracket (5 PCS) 9.) Fan Light 10.) Glass Shade (3 PCS) 11.) Assembly Kit 12.) Installation Instructions 13.
Exploded View Detail Hanger Bracket Hanger Ball Canopy Canopy Cover Downrod Lock Pin Hanger Pin Downrod Stand Cover Collar Housing Blade Bracket Blade Switch Box Cover Switch Box Glass Shade LED Bulb Fan Light Fan Light Switch Dual Mount Options Downrod Mount Slope Ceiling Mount (Up to 23 degrees) PAGE: 3 / 10 181128
Safety Instructions READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN TO INSTALL THE FAN AND SAVE INSTRUCTIONS. All set screws of the fan must be checked and retightened where necessary before installation. To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades or cleaning the fan. Do not insert foreign objects between rotating fan blades.
INSTALLATION INSTRUCTIONS IMPORTANT: BEFORE YOU BEGIN INSTALLATION, CAREFULLY READ ALL INFORMATION PROVIDED ON THE SAFETY INSTRUCTIONS AND INSTALLATION INSTRUCTIONS. IF IN DOUBT, CONSULT A QUALIFIED ELECTRICIAN. SAVE ALL INSTRUCTIONS. NOTE: The fan weight is 19.18 lbs (8.7 kgs). Be sure the outlet box you are using is securely attached to the building structure and can support the full weight of the fan. Failing to do so can result in serious injury.
For a single switch Follow these steps: ck Bla e Whit White G ro Blue Connect the black (hot) wire (This is for fan control) and blue wire (This is for light control) from motor to the black (hot) wire from outlet box with a wire connector. en Gre Connect the white (neutral) wire from motor to the white (neutral) wire from the outlet box with a wire connector. un Connect three ground wires (Green or bare copper) coming from outlet box, downrod and hanging bracket with a wire connector.
Fig.10 Fig.12 Hanger Bracket Blade Screw Washer Canopy Screw Blade Canopy Canopy Cover Slide the canopy up to ceiling and over the two canopy screws on hanger bracket. Rotate canopy clockwise, next, while holding the canopy with one hand, slide the canopy cover over the screws and rotate counter-clockwise until tight. Note: Adjust the canopy screws as necessary until the canopy and canopy cover are snug. Fig.13 Fig.
Fig.16 Make wire connection: -- connect the blue wire from the switch box to black wire from the fan light with wire connector. -- connect the white wire from the switch box to white wire from the fan light with wire connector. Switch Box Wire Connector Fan Light Fan Light Fig.15 Set Screw Light Kit Switch Carefully put the wires into the switch box, then attach the fan light into the switch box with the switch box screws. Fig.
Trouble Shooting Guide If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation or wiring. If you experience any faults, please check this Trouble Shooting Guide. If a problem cannot be remedied or you are experiencing difficulty in installation, please call our Customer Service Department (1-800-887-6326). PROBLEM SUGGESTED REMEDY 1. If fan does not start: 1. Check main and branch circuit fuses or circuit breakers. 2.
DYNAMIC BLADE BALANCING KIT YARDSTICK 1 BALANCING WEIGHT CENTERLINE 2 3 4 5 6 7 8 MEASURING POINT 9 PLASTIC CLIP COUNTERCLOCKWISE PREFACE Your ceiling fan may sometimes have wobbling problems when operating due to irregularity in the blades or the blade brackets. Improper assembly in the mounting system may cause some additional problems. This balancing kit can be used to fix wobbling problems. DYNAMIC BLADE BALANCING KIT FOR CEILING FANS 1.
