ELECTRIC FIREPLACE HOMEOWNERS OPERATING MANUAL MODELS：ZF36D03F ZF42D03F ZF50D03L 261046 ZF60D03L CONSUMER SAFETY INFORMATION: PLEASE READ THIS MANUAL BEFORE INSTALLING AND OPERATING THIS APPLIANCE. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN A POSSIBLE ELECTRIC SHOCK, FIRE HAZARD, AND/OR INJURY AND WILL VOID THE WARRANTY. WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED, AN ELECTRIC SHOCK OR FIRE MAY RESULT IN PROPERTY DAMAGE, PERSONAL INJURY, OR LOSS OF LIFE.
IMPORTANT INSTRUCTIONS When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock, and/or injury including the following: 1. Read all instructions before using this heater. 2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. DANGER: High temperature may be generated under certain abnormal conditions.
PACKAGE CONTENTS CODE DESCRIPTION QTY 1 Fireplace 1 2 Glass Front 1 3 Mounting Bracket 4 Acrylic Crystals 1 Bag 5 Hardware Screw Bag 1 Bag 6 Remote Control 1 7 Manual 1 (Attached To The Fireplace 1 1 ) 2 1 3 A x4 B x6 4 C x2 5 6 03 7
SPECIFICATIONS Model NO. ZF36D03F ZF42D03F ZF50D03L ZF60D03L Dimension (W x D x H) 36” x 4.2” x 16” 42” x 4.2” x 16” 50” x 4.2” x 18.6” 60” x 4.2” x 18.6” Voltage 120 V 120 V 120 V 120 V Rating 1400 W 1400 W 1400 W 1400 W Frequency 60 Hz 60 Hz 60 Hz 60 Hz PRE-INSTALLATION Figure 1 A GROUNDING INSTRUCTIONS: This heater is for use on 120 volts. The cord has a plug as shown at (A) in figure 1.
Do not share a socket with other appliances when using electric fireplaces, please use a dedicated socket. √ × × Never use with an extension cord or relocatable power tap (outlet / power strip).
INSTALLATION (WALL MOUNTING) 1. Remove the mounting bracket from the back of the fireplace. 1 3 2. Attach the mounting bracket to a wall. NOTE: Wall anchor is not needed if the bracket is to be mount directly on the wall studs. A x4 A x4 3 B x4 B x4 3. Hang the fireplace on the mounting bracket. Secure the fireplace to the mounting bracket with the two screws removed in Step 1.
4. Place decorative crystals inside the fireplace. 4 5. Put the glass front panel on the fireplace. CAUTION: Careful when handling glass to prevent injury or damage. wall 6. Secure the glass front panel to the fireplace with the provided screws C.
INSTALLATION (IN WALL) Cabinet - in / cm Model fireplace - in / cm A B C Model A1 B1 C1 ZF36D03F 33.6/85.3 15.8/40.2 4.9/12.4 ZF36D03F 33.1/84.1 15.4/39.2 3.8/9.7 ZF42D03F 39.6/100.6 15.8/40.2 4.9/12.4 ZF42D03F 39.1/99.4 15.4/39.2 3.8/9.7 ZF50D03L 47.6/120.9 18.4/46.7 4.9/12.4 ZF50D03L 47.1/119.7 18.1/46.0 3.8/9.7 ZF60D03L 57.6/146.3 18.4/46.7 4.9/12.4 ZF60D03L 57.1/145.1 18.1/46.0 3.8/9.
2. Remove the Hang board from the back of the fireplace. NOTE: Screw back the 7 screws to the fireplace. 3. Plug into the power supply and push the fireplace into the cabinet. 1 2 4. Use supplied screws B to secure the fireplace to cabinet.
5. Place decorative crystals inside the fireplace. 4 6. Put the glass front panel on the fireplace. Then secure the glass front panel to the fireplace with the provided screws C. CAUTION: Careful when handling glass to prevent injury or damage. CAUTION: After hanging the glass front panel, 1 minute to recheck the touch-panel is necessary. Otherwise it will touch without any reaction.
OPERATING INSTRUCTION Control Panel The control panel is located on the top right corner of the unit. To control the unit, touch any button to wake up the control panel. The power button will flash, and all other buttons will light up. The control panel will turn off after 10 seconds of inactivity. Brightness Button Display Window Timer Button Ember Bed Button Flame Button Heat Button Power Button Power The Power Button turns the fireplace ON and OFF.
Timer The TIMER has adjustable setting at range from 1 hour to 9 hours and OFF. As shown the following: 1h-2h-3h-4h-5h6h-7h-8h-9h-OFF. Once you have set the timer, and the timer is up, it will close all the functions and enter standby mode. In this mode, you should touch the power button to restart the fireplace. Ember Bed This button is used to turn ember bed ON, to alter the ember bed color and to turn ember bed OFF.
REMOTE CONTROL Power The Power Button turns the fireplace ON and OFF. Heat The Heat Button turns the heat ON and OFF. Press “+” or ”-” button to set the temperature. Flame The Flame Button turns the flame ON and OFF. Press “+” or ”-” button to set the flame color. Ember bed The Ember Bed Button turns the ember bed ON and OFF. Press “+” or ”-” button to set the ember bed color. Timer The Timer Button turns the timer ON and OFF. Press “+” or ”-” button to set the timer.
MAINTENANCE Clean the metal trim using a water-dampened soft, clean cloth. DO NOT use brass polish or household cleaners as these products will damage the metal trim. The motors used on the fan and the flame generator assembly are prelubricated for extended bearing life and require no further lubrication. However, periodic cleaning/vacuuming of the fan/heater and air intake/output vents is recommended.
