PARAGON BATH SHOWER DOOR/ BATH TUB SCREEN INSTALLATION INSTRUCTIONS H7-11206 ………………………………………………………………………………………… Please read these instructions carefully before installing. If you have any questions regarding installation, please call our technical support specialists Monday through Friday 9:00 AM – 5:00 PM at Phone: (888) 895-1989, or e-mail our technical support group at Support@Paragonbath.com. For more information on Paragon Bath Shower Doors & Tub screens please visit www.ParagonBath.
Installing Preparations 1. After opening the carton, please read the instructions carefully, examine boxes and packages for shipping damage. If the unit has been damaged, has a finishing defect, or has missing parts, please contact our customer support department within 3 business days of the delivery date. Please note that Paragon Bath will not replace any damaged products or missing parts free of charge after 3 business days or if the product has been installed.
DetailedDiagramofShower/BathtubscreenComponents Component list No. Name Q’ty No.
07 Decorative profile 2pcs 22 Vertical profile dustproof cover right 1pc 08 Bottom guide track 1pc 23 Wall profile dustproof cover right 1pc 09 Upper guide track 1pc 24 Glass bottom fixed part 1pc 10 Profile adjust block 6pcs 25 Bottom block 4pcs 11 Philips head screw ST4*12 10pcs 26 Inner side moving glass 1pc 12 Wall anchor 6pcs 27 Middle moving glass 1pc 13 Philips head screw ST4*30 6pcs 28 Stationary glass 1pc 14 Philips head screw ST4*20 10pcs 29 handle 1p
2. Check the guide track Your Guide tracks (08&09) has been precut for your shower model width:59”. If W-width of your wall-to-wall opening is equal to the size of your Shower model, it is unnecessary to cut the Guide tracks .If W-width of your wall-to-wall opening is less than the size of your Shower model, you will need to cut the Guide tracks. upper guide track and bottom guide track both cut in the same side which close to the moving glass.
3. In order to make it easy for following installation of frames, it’s better to tapping on both sides of the upper and bottom guide tracks. Use Philip’s screw ST4*20(14) to lock to both ends of upper and bottom guide track, then loosen the screws. Please see Fig 4 for details Fig 4 4. Drilling new holes on bottom guide track 4.
Fig 5 4.2. Use 1/8” drill bit to drill holes on bottom guide track Please see Fig 6 for details Fig 6 5. Determine shower door location. 5.1. Put the Wall profile (5) to the wall above the shower base and level it vertically. Mark the drilling holes on the wall through the holes in the Wall profile. 5.2. Remove the wall profile, use electric drill with 1/4” drill bit to drill holes and use hammer to drive the Wall anchors (12) into the wall.
6. Assemble the upper guide track push the wheel set into track 01 and track 02, and push wheel set buffer blocks into track 01. Kindly note: Top guide track comes with gear system and gear strips assembled.
7. Assemble frames 7.1 Use Philips head screw ST4*20(14) to lock the upper and bottom guide tracks to the vertical profiles(6) Important note: before assemble frames please make sure the wheel set and buffer block already install on top guide track. Refer to above Fig 6 Please see Fig 10 for details Fig 10 7.2 use straight screw driver to lock vertical profile(6) to wall profile(5).
Fig 11 8. Place the complete frames to the two walls and use Philips head screws ST4*30(13) to fix the frames to the walls.
Fig 12 9. Install stationary glass 9.1. Snap the glass pad (18) into the bottom guide track. 9.2. Snap the glass connect part (20) to the glass and place the stationary glass (28) to the glass pad, then push the stationary glass into the vertical profile slowly and gently. 9.3. Use Philips driver to lock the glass fixed parts on upper (17) and bottom (24) with Philips head screw ST4*12, then fill with screw covers (19).
Fig 13 10. Install middle moving glass 10.1 Please make sure the gear strip is well connected to the profile, and then make sure the pull riverting screw is installed on the gear strip side. Please see Fig 14 for details Fig 14 10.2 Place the middle moving glass (27) to the upper guide track slot tipsily and then adjust it slowly and gently till it is straight to the upper and bottom guide tracks slot. Later insert the wheel set sheath to the moving glass profile slot.
P lease see F ig 15 fo r de ta ils Fig 15 11. Install inner side moving glass 11.1 Please make sure the inner moving glass pull riverting screw is on the side of small gear wheel. The big gear wheel is on inner side and the small gear wheel is on outer side. Please see Fig 16 for details Fig 16 11.2 Inner side moving glass (26) installation step is same with the installation step of middle moving glass. For details please refer to 9.2 and Fig 13. 12.
Please see Fi g 17 for details Fig 17 13. Install magnetic strips and waterproof strips Please see Fig 18 for details Fig 18 14. Install gap sealing strip. All the Paragon bath shower door/tub screens comes with gap sealing strip(21), its function is to seal the tiny gap between stationary glass and aluminum profile. After you install the glass please insert the rubber to seal it for getting perfect waterproof result.
. Install handle(29) Kindly note: Handle set already assembled, you just need to disassemble during install on glass door and lock every part will be done. Please see Fig 20 for details Fig 20 16. Adjustment of inner side moving glass. Pull the wheel set sheath a little out from the guide track, use Philip’s screw driver to adjust the high of wheel set sheath until the big gear and the guide track gear strip get good grip.
17. Adjustment of middle moving glass. Pull the wheel set sheath a little out from the guide track, use Philip’s screw driver to adjust the high of wheel set sheath until the small gear and the guide track gear strip get good grip. Step same as above Fig 21. Kindly note: If the grip between gear and gear strip is too tight will increase heavy to open the door. While if the grip between gear and gear strip is too loose, the moving orders will be upset between inner side moving glass and middle moving glass.
Fig 23 19.
20. Apply the sealant along the profiles and guide tracks. on the seams between the bottom guide track and the profiles as well as along the shower base.
ProductMaintenance To ensure long lasting life for your shower door/bath tub screen, please clean the dust or stains use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. To ensure a long lasting hardware finish, wipe off the metal parts after each use with a soft cloth. Do not use abrasive cleaners or cleaning products containing ammonia, bleach or acid.
WARANTY INFORMATION This is Paragon Bath LLC exclusive written warranty effective August 8, 2014 This warranty extends only to the original owner/end-user for household use only and is not transferable to a subsequent owner. This warranty applies only to Paragon Bath LLC products purchased from an authorized dealer and installed in United States or Canada. Proof of purchase (original sales receipt) must be provided with all warranty claims.
material, including but not limited to tiles, marble, contract, negligence, strict liability in tort, or warranty of any kind) for any indirect, special, incidental, consequential, or exemplary damages (including but not limited to lost profits). Paragon Bath LLC is not responsible for installation, removal or reinstallation costs of any product requiring warranty services. Improper modification or alteration of any Paragon Bath LLC products will void the warranty.
Paragon Bath LLC is not responsible for product code compliance or for verifying building code restrictions on installation or use and any such compliance is excluded from this warranty. Paragon Bath LLC reserves the right to modify this warranty at any time - such warranty modification will not alter warranty applicable at the time of sale of the products in question. Product must be registered within 30 days from time of purchase at www.ParagonBath.com WARRANTY Paragon Bath LLC.
