® A d j u s t a b l e Wo r k P l at fo r m O P E R AT O R ’ S M A N U A L For Models 1101 & 1101-96 (Model 1101 illustrated in this manual) WA R N IN G Re a d a nd becom e fam iliar w i t h t h i s ma n u a l BE F O RE o p e r a t i n g u n it . Before operating this equipment, thoroughly read this set of instructions, make sure you understand them, and only then follow the step-by-step directions. Failure to do so could result in serious property damage and / or serious bodily injury or death.
To our valued customer, Thank you for choosing a product by Paragon Pro Manufacturing Solutions. We are pleased that we are able to provide equipment to make your work easier. Our efforts are focused on producing the finest quality equipment of which we are capable. We make sure to spend extra time and effort on our design and production in order to reduce your time and effort spent using the product. We take pride in providing the best for our customers.
CONTENTS This manual covers TELE-TOWER® Adjustable Work Platform Models 1101 and 1101-96. NOTICE: All contents of this manual are copyrighted and nothing may be reprinted in whole or in part without prior written permission. Warning / Instructional Information. . . . . . . . . . . . . . . . . Pages 1-2 User Components & Product Specifications . . . . . . . . . . . . Page 3 Care & Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4 Assembly . . . . . . . . . . . . . . . . . . .
Warning Read and follow these warnings and the instructions that follow. Failure to do so could result in serious property damage and/or serious bodily injury. • BEFORE operating this equipment, thoroughly read this • USE ONLY factory authorized accessories and replacement parts. Installation or use of other parts can compromise the safe design of the Tele-Tower® Adjustable Work Platform and may cause failure of the unit possibly resulting in serious property damage and/or serious bodily injury.
Warning Read and follow these warnings and the instructions that follow. Failure to do so could result in serious property damage and/or serious bodily injury. • NEVER make height adjustments while a person is on the platform. Doing so can subject the cable lift assembly to stresses and loads that it was not designed to carry.
USER COMPONENTS & SPECIFICATIONS A. Telescoping end section “A” with integral outriggers B. Telescoping end section “B” with integral outriggers C. 5” heavy-duty swivel / brake scaffold casters D. Connecting beam with cable elevation mechanism E. Guard rails (4) F. Safety Chains (4) G. Interchangeable anti-sway braces (6) H. Steel safety deck with 4” toe board • Model 1101 & 1177: (approx. 20” x 6 feet) • Model 1101-96 & 1177-96: (approx.
CARE AND MAINTENANCE The following items shall be inspected at a minimum each time the Tele-Tower® Adjustable Work Platform is assembled. Determining a need and implementing a schedule for more frequent inspection based on usage patterns specific to the deployment of the equipment by the owner shall be the responsibility of the equipment owner under the direction of a designated Competent Person as defined by OSHA [29 CFR 1926.32(f)]: • Inspect the cable assembly.
ASSEMBLY A B Tighten Securely 3) Rotate winch handle counterclockwise and release cable from storage on beam. 1A) Place connecting beam in tapered socket and secure with bolt and wing nut as shown. 1B) Lift retaining bolt and tighten wingnut until secure. (Make sure that blade is secure in slot) NOTE: When disassembling, loosen wing nut and pivot latch bolt assembly to pry tapered socket open. 2) Engage ladder lock pins and lock one caster on end Section “B”.
ASSEMBLY continued 5) Attach cable ends to hooks on top of end sections. 7) Jog base of end sections to facilitate brace pin alignment. DO NOT hammer on braces. 6) Attach braces between the beam and the base of each end section. WARNING: NEVER operate the Tele-Tower Adjustable Work Platform without these braces. Doing so can result in damage to the structure which can lead to failure that can result in severe property damage and or severe bodily injury or death.
ASSEMBLY continued 10) Install the guard rails in the top of the telescoping ladder sections. CAUTION: Keep fingers clear of hinge joints when handling guard rails. 9) For deck heights of 6’ or greater, place the deck on the top rungs of the telescoping ladders and attach ALL FOUR deck braces between the deck and the base of the telescoping ladders. Jog base of end sections to facilitate brace pin alignment. DO NOT hammer on braces.
Operation Raise and rotate latch pin to disengage and adjust outrigger.” 1) Adjust base outriggers to maintain height to base ratio in keeping with applicable national, state, local and ANSI Standards. ALWAYS engage the outrigger latch pin before climbing the Tele-Tower® Adjustable Work Platform. 2b) Rotate winch handle clockwise until deck is 2” - 4” below the desired height. 2a) TO ELEVATE DECK: —Retract and rotate the ladder lock spring pins to the disengaged position.
Operation continued WARNING: -ALWAYS make sure ALL FOUR ladder lock spring pins are fully engaged before climbing. -NEVER make height adjustments while a worker is on the work platform. (see warnings, page 1-2.) WARNING: While operating the Tele-Tower® Adjustable Work Platform, ALWAYS keep the cable taut under the telescoping ladder sheaves. NEVER rotate the winch handle counterclockwise while the ladder lock pins are engaged.
ASME Standards for wire rope (cable) inspection and replacement Reprinted with permission from ASME B30.19 Cableways The following is intended as a helpful guide to the general topic of inspection and replacement of wire rope (cable). It is not intended to be an exhaustive treatment of the topic. Frequent inspection (at least daily) and prompt replacement of any cable that shows any sign of wear is the responsibility of the owner and the operator of the Tele-Tower® Adjustable Work Platform.
PARTS INDEX Models 1101 & 1101-96 14-00 (Model 1101) 14-08 (Model 1101-96) 14-01 12-00 (Model 1101) 12-03 (Model 1101-96) 7-00 7-00 13-00 8-00 (Model 1101) 8-33 (Model 1101-96) 6-0A Form 14-11-00-00 version 10 13-00 - 11 - 6-0B © 2019 Paragon Pro Manufacturing Solutions All Rights Reserved.
PARTS INDEX Models 1101 & 1101-96 PARTS LIST Part Description 6-0A 6-0B 6-01 7-00 7-01 7-02 8-00 8-01 8-02 8-03 8-04 8-05 8-06 8-07 8-08 8-13 8-14 8-16 8-17 8-18 8-19 8-20 8-22 8-31 8-32 8-33 8-34 9-00 10-00 12-00 12-03 End section “A” (crank side) without removable parts End section “B” (non-crank) without removable parts Latch pin with fasteners (each) Complete telescoping ladder section (each) (total of 2) Cable sheave with Axle and Pin Ladder lock spring pin with fasteners Complete beam assembly for
This product contains trace amounts of the following items which are known to cause These chemicals are not hazardous under product's intended use. Please review CAS# for more information.
Questions about assembly? Can’t find a part? Need some other help? Call us: 1.800.448.0822 We’ll get you set up! Paragon Pro Manufacturing Solutions 7251 S. 42nd St., Grand Forks, ND 58201 701-775-0551 www.paragonpromfg.com Form 14-11-00-00 version 10 © 2019 Paragon Pro Manufacturing Solutions All Rights Reserved.
