5 Hee (5) (5); Gazebo GZH4-1214BKD Aluminum Composite Root Panels Assembly Instructions Customer 782 4482 \ Paragon Group USA | v1
Introduction Thank you for purchasing the Gazebo GZH4-1214BKD. When properly assembled and maintained, this gazebo will provide many years of enjoyment! These instructions include helpful hints and important information needed to safely assemble and properly maintain the gazebo. Please read these instructions completely before you begin. Our patented gazebo has been designed for easy assembly. All steps can be completed by a team of four people. The assembly should ake about two hours.
Safety Advice * The gazebo must be positioned and fixed on a flat level surface. Dispose of all plastic bags safely. Keep them out of the reach of children. Keep children and pets away from the assembly area until the work is completed. Always wear shoes, gloves and safety goggles when working. Take special care not to touch overhead power lines with the aluminum profiles. Do not attempt to assemble the gazebo in windy or wet conditions. Do not position your gazebo in an area exposed fo excessive wind. .
List of Paris The gazebo is shipped in five cartons. These carton are heavy. Be careful when lifting them. Wear proper safety gear including work shoes, gloves and goggles. The parts are identified by removable sticks. Place all the parts for each step in staging areas, checking that you have all parts as you go. If any pairs are missing or damaged, contact customer service before beginning assembly: Customer 782 4482 No. Profile Qty | Step | Box | | No.
No. Step | Box | | No. Profile Gly | Step | Box 19 71530 = i 11513 Aluminum Composite Roof Panel Roof Top Connector Beam 20 7153 oF 32125] 3 Screw Minimal Composite Roof Panel MéxBmm 20n| © as = 180 apse 3 W Screw Q Top center connector Méx18mm 7533 Oo 3216] 3 Screw Méx25mm 7534 oo 8|5]3 Screw Aluminum Composite Roof Pans! M6x33mm © AER U-shaped Connors Méx38mm 2 NN 6236 853 Roc Prof Se raw 9 409mm Méx45mm 1873 Roof Profile ’ Craw 1000mm Maxima 1415 | 3 AS Nut © 1000mm Mé 27 623 A\} 3233 Roof Profile 823mm
No. Profile Gy | Step | Box | | No. Profile Qly | Stop | Box 43 co=meQO [16] 43 ||51 41213 Concrete Bolts, washers a M8x70mm Rail connector 4 “Tm NUT 3 53 Spam er Magnetic hex key 1063 53 2 Hook 46 SF 6153 1]5]3 T connector Roof Top Cover 47 Sg= 453/55 253 X counselor Aluminum Composite Roof Panel 48 Ce ES 4536 253 Top center connector Aluminum Composite Roof Panel 4 613 62 253 Aluminum Composite Roof Panel We included some extra screws and bolts for your convenience.
STEP 1 Assembling the Corner Profiles Place all the parts on a level surface. I< NN CEN Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles.
support frame (2] if you purchased the screen netting. ATTENTION:Note: Do not need to assemble Slide support frames (2) over lower end of corner profiles (1). Attach support plates (3) to corner profiles (1) as shown, using screws (33) for each plate. J VF a Leave support frames (2)about 10"over lower end of corner profiles (1) until step 4.
STEP 2 Assembling the Rails Components Screw (31) Short Rail (5) Short Rail (6) Inner Roof Connector Long Rail (7) Long Rail {8) Outer Roof Connector (10) Screw (32) x2 x2 x18 x 64 Insert rail connector (51) into blunt end of short rail (5) secured with screws (31). Insert long rail (5,51) into blunt end of short rail (6) secured with screws (31). Repeat lo create two less of short rails. Insert rail connector (51) into blunt end of long rail (7) secured with screws (31).
Attach four outer roof connectors (10) and three inner roof connectors (9) to each short rail set (5+6) at per-drilled screw holes, using screws (32). En {VIEW FROM SIDE {VIEW FROM THE TOP ; Attach five outer roof connectors (10) and four inner roof connectors (9) to each long rail set (7+8} at per-drilled screw holes, using screws (32). El (VIEW FROM SIDE Sry ATTENTION: Attach roof connectors facing exactly in the directions shown.
STEP 3 Assembling the Rails io the Corner Profiles Attach one roof profile set (5+6) to two corner Components profiles (1) as shown, using screws (32) and supplied magnetic hex key {44) through holes in A\Y SN profile set. Screw (32) Plastic Cap #3 (39) Magnetism hex Key (44) Close holes in profile set with plastic caps #3 {39). Repeat step 3.A and 3.8 fo create two less.
Using at least 3 people, attach the remaining two roof profile sets fo corner profiles (1), connecting all four corner profiles {1). Fasten with four screws (32) and supplied magnetic hex key {44} on each side. Close holes in profile sets with plastic caps #3 (39). IMPORTANT: After this step you should place he gazebo frame in ifs desired location. Make sure dll corners are squared at 90 degrees.
STEP 4 Secure the Gazebo to a Concrete 7-7 Floor or Wood Deck | Components Concrete Floor: 1.Drill holes approx. 3.00 inches deep and use a mallet to set up. CEE masonry drill bit to drill holes for the concrete anchors supplied. QQ 3.Using a concrete drill, drill holes into the concrete floor, corresponding to the holes in support plates (3). 4.Insert concrete bolts (43) into the holes and hammer into place, using a mallet. Concrete bolts, washers and nus (43) x16 5.
STEP 5 Installing the Lower Roof Gable Profiles ATTENTION: DO NOT ATTEMPT TO ASSEMBLE THIS ALONE Roof gable profile{11) Roof gable profile{12) Roof gable profile{13} Roof gable profile{14} Roof gable profile(15) Top center 2469mm 1808mm 949mm 949mm 1790mm subcontractor Shaped Roof tof Roof of Setscrew) Screw(34) Screw(35) Screw(36) connector{23) connector bandsman) connector baam(30} x1 x64 x8 x12 Nuisance) Plastic Cap #1 Vlasic Cap #2 Connector X-connector top center M6 140) wl we 147) owl) x14 Roof gable
Upper end Lower end -— Roof Gable Profile |1 1) EEE 2469 mm Roof Gable Profile (12) Freer eee ee min 1 808mm Roof Gable Profile 13) EE 949mm Roof Gable Profile (14) EEE rear ee 049mm Roof Gable Prole 15) Fee eee eee eee ee 1790mm Using screws (34) and nuts {38), connect roof gable profiles (11) to corner roof connectors (4} on fop of corner profiles (1). Using screws {32), connect roof gable profile (11) to roof top connector beam (30) as shown.
Install roof gable profiles (12) Using screws (50) and nuts (38), connect top center connector {48) fo roof op connector beam (, Using screws (32), connect roof gable profiles (15) to inner roof connector (9) on rail sets (7+8) and the other end to roof top center connector (48). Using screws (32) connect roof gable profiles (12) to inner roof connector (9) on short rail sets (5+6) and the other end to roof top connector beam (30).
Connect the roof top cover (54) to roof top connector beam (29) by attaching U-shaped connectors (23) from above, using two screws (36). Using screws (50) and nut (38), connect two top center connectors (20A) fo roof top connector beam (29). Using screws (32), connect roof gable profile (52) to roof top connector beam (29). Using screws (32), connect two roof gable profile (53) fo top center connectors (20A).
IMPORTANT: Cecily cut on the edge of the panels on both side with knife and remove protective plastic of roof panels. Place with black surface toward the sun facing oul when installing. “eo so Fit roof panels (62,61) on top of roof gable profiles (52 and 52). Place roof gable profile (53A) on the top of roof gable profile (53) and fasten with two screws (35) from below (inside gazebo).
Fit roof pane! (55) on the top of roof gable profiles (52,52). Place roof gable profile (52A) on the top of roof gable profile (52), and fasten with two screws (35).
Fit the roof panel {55} on top of roof gable profiles (52,52) . Place roof profiles (52A} on top of roof gable profiles (52), fasten with screws (35) from below. Close off roof gable profiles (53) with plastic cap #1 (40) and roof gable profiles (52) with plastic cap #2 (41).
Attach T-connectors {46) lo underside of roof gable profiles {12,15), using screws (32) as shown. Attach X-connectors vd fo underside of roof gable profiles {11), using screws {32) as shown. Connect profile (13,14) to X-connectors (47) and the other end to inner roof connector (9) using screws (32).
STEP 6 Installing the Horizontal Roof Profiles: [ Components | NOS NNN 5 Roof profile {24) Roof profile (25) Roof profile {26) Roof profile {27} Roof profile (28} 409mm 1000p 1000mm 823m 823m Comer vr 49) Hock He Crow Attach roof profiles (24,25,26,27,28) to T-connectors {46) and X-connectors [47]. Attach Hook (45) on the roof top connector beam (30). Place corner cap (49) on the top of comer profile {1) and fasten with screw (33).
STEP 7 Installing the Roof Panels and Upper Roof Profiles IMPORTANT: Gently cut on the edge of the panels on both side with knife and remove protective plastic of roof panels. Place with black surface toward the sun facing out when installing. Components Tm, Th, Thu, ThE, Th OP = Goober © Gobbler © Beetroot Root gable Root gable Nome Comment 1 ile (15, \minimum Composite Pm Plasma) Pai PA Pan Sew (37) Wares (35) x18 x74 x2 Aluminum Composite Aluminum Composite Aluminum Composite Aluminum Composite Aluminum
Fit roof panel (16) on fop of roof gable profiles (15) as shown and fasten with one screw (37) underneath of outer root connector (10). IMPORTANT: Make sure that the roof panels are installed exactly in the order shown, otherwise it will be difficult to place the top roof gable profiles.
Place roof gable profile (15A) on top of roof gable profile (15) as shown and fasten with screws (35) from below (inside gazebo).
Fit roof panel (18) on top of roof gable profiles (14,15) as shown and fasten with screw (37) fo outer roof connector (10) from below. Place roof gable profile {1 on top of roof gable profile (15) as shown. Align both profiles, and fasten with fre screw (35) fom below (inside gazebo).
Fit roof panel (19,20,21,22) on top of roof gable profiles (11,12,13,14) as shown and fasten with one screw (37) underneath of outer roof connector (10). Place roof profiles (11A,12A) on top on roof profiles {11,12) and fasten with screws (35) from below.
Continue in a clock-wise direction as shown. Place the roof panel (19,20) on top of profiles (11,13,14) , fasten with screw (37) to outer roof connector (10) from below. Place the roof gable profile (1 1A) on top of roof gable profile {11}, fasten with screw {35} from below of roof gable profile {11).
Place the roof gable profile {13A) on top of {13}, fasten with screw (35) from below of roof gable profile (13). Plastic Cap #1 (40) Plastic Cap #2 (41) x 14 x4 Close off roof profiles 5 2/1 Jana with plastic caps #1{40) and roof profiles {11} with plastic caps #2 (41).
Gazebo GZH4-1214BKD Aluminum Composite Root Panels Assembly Instructions WARRANTY: Warranty covers damage due to manufacturing defects only for a period of 5 years on the structure, and 5 years on the Aluminum Shell from date of purchase. Warranty does not cover weather inflicted damage and/or damages causes caused by not following assembly instructions and adhering to warnings in manual. Warranty does not cover user error, negligence, or misuse.