Gazebo GZ620LS Assembly Instructions 13’ 9’ 1 1’’ 11’ 8’ 1 2’’ 7’2” 9’2” 11’’ 1’’ Systems Trading Corporation 450 7th Avenue Suite 2809, New York, NY 10123 Customer service: (877)782 4482 Email: easygrow@stcaustin.com www.stcny.
Introduction Thank you for purchasing the Gazebo GZ620LS. When properly assembled and maintained, this gazebo will provide many years of enjoyment! These instructions include helpful hints and important information needed to safely assemble and properly maintain the gazebo. Please read these instructions completely before you begin. Our patented gazebo has been designed for easy assembly. All steps can be completed by a team of three people. The assembly should take about two hours.
Safety Advice Table of Contents • The gazebo must be positioned and fixed on a flat level surface. • Dispose of all plastic bags safely. Keep them out of the reach of children. • Keep children and pets away from the assembly area until the work is completed. • Always wear shoes, gloves and safety goggles when working. • Take special care not to touch overhead power lines with the aluminium profiles. • Do not attempt to assemble the gazebo in windy or wet conditions.
List of Parts The gazebo is shipped in two cartons. These cartons are heavy. Be careful when lifting them. Wear proper safety gear including work shoes, gloves and goggles. The parts are identified by removable stickers. Place all the parts for each step in staging areas, checking that you have all parts as you go. If any parts are missing or damaged, contact STC customer service before beginning assembly: Customer service: (877)782 4482 Email: easygrow@stcaustin.com No. Profile 1 Qty Step No.
19 4 8 27 28 20 21 22 4 2 4 23 4 24 12 25 12 26 10 www.stcny.com 140 1,2, 4,6 34 9 8 29 16 7,8 30 10 7,8 31 2 7 32 2 7 33 1 8 2 3 9 We included some extra screws and bolts for your convenience.
STEP 1 Assembling the Corner Profiles Place all the parts on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. Components 1.A Place corner profiles (1) parallel to each other the ground. Slide support plates (2) into corner profiles from the end with a single screw hole, as shown.
STEP 2 Assembling the Roof Profiles 2.A Insert connecting profile (22) into long roof profiles (3,4). Components Screw (27) x 16 Roof profile (3) 1822mm Roof profile (4) 1822mm x2 x2 Connecting profile (22) x2 4 22 x2 3 4 22 4 3 22 3 2.B Fasten together using screws (27). Repeat steps 2A and 2B to make the two long roof profile sets. 4 3 27 www.stcny.
2.C Insert connecting profile (22) into short roof profiles (5,6). Components Screw (27) Roof profile (5) 1350mm Roof profile (6) 1350mm x2 x2 Connecting profile (22) x2 6 22 5 6 22 6 5 22 5 2.D Fasten together using six screws (27). Repeat steps 2A and 2B to make the two short roof profile sets. 6 5 27 ATTENTION: Insert screws exactly as shown. You will need the two empty screw holes to fasten connector (8) in step 4. www.stcny.
STEP 3 Attaching Roof Profiles to Corner Profiles 3.A Attach long roof profile set to corner profiles as shown, making sure the side with the ridge faces toward the corner profiles. Components Screw (29) 29 3 4 x8 1 29 x2 1 3.B Fasten together using two screws (29) on each side. Repeat to create two sides for the gazebo. 4 3 3 4 29 1 1 1 www.stcny.
3.C Components Using three people, attach the short roof profile sets to corner profiles as shown, making sure the side with the ridge faces toward the corner profiles. Use screws (29). Screw (29) x8 29 5 4 29 6 3 6 3 5 4 29 1 6 29 3 1 ILLUSTRATION www.stcny.
3.D Attach corner connecting part (23) to inside of each corner using seven screws (27) for each corner. Components Screw (27) x 28 Corner connecting part (23) x4 23 27 1 IMPORTANT: After this step you should place the gazebo frame in its desired location. Make sure all corners are squared at 90 degrees. www.stcny.
STEP 4 Attaching the Roof Connectors 4.A Attach roof connectors (7) to roof profiles (3,4,5,and 6) as shown, using two screws (27) for each connector. 27 27 7 7 27 7 7 4 5 7 6 27 Screw (27) x 10 x6 x4 x 48 27 7 7 27 27 27 27 27 4.B Roof connector (9) 3 4 7 7 Roof connector (8) 7 7 5 Roof connector (7) 27 6 3 Components Attach roof corner connectors (9) to roof profiles (3,4,5,and 6) as shown, using four screws (27) for each connector. 9 27 9 27 9 27 9 27 27 www.
4.C From inside of the gazebo frame, attach roof connectors (8) to roof profiles (3,4,5 and 6) as shown. 8 8 27 27 3 6 8 27 27 8 27 27 8 5 4 8 6 5 8 3 5 6 27 4 8 3-4 27 ATTENTION: Insert screws exactly as shown. In roof profiles (5,6), use empty screw holes. In roof profiles (3,4), use pre-drilled screw holes. STEP 5 Securing the Gazebo to the Ground 5.A Fasten the gazebo frame to the ground, using three spikes (24) for each support plate.
STEP 6 Installing the Roof Gables Components Roof top plate (18) Roof top plate (10) Roof gable (11) 2171mm Roof gable (12) 1584mm x1 x1 x4 x6 6.A Screw (27) x 24 Using at least three people, install the roof gables (11,12) in the following order: 4. 11 3. 2. 1. 12 12 18 12 11 4. 4. 11 12 12 12 2. 1. 3. 11 4. VIEW FROM TOP IMPORTANT: The roof gable profiles (11,12) have pre-drilled screw holes underneath on each end.
Using screws (27) connect profiles (12) one end to roof top plate (16) and the other end to roof connectors (8). 12 12 18 8 27 27 ILLUSTRATION 6.B Install roof gable profiles (11) in the same way. Using screws (27) connect profiles (11), one end to roof top plate (16) and the other end to roof connectors (9). ILLUSTRATION 12 18 27 11 9 27 1 www.stcny.
6.C Connect the roof top plate (10) to the roof top plate (18) as shown, using four screws (27). 10 18 27 27 10 18 27 VIEWS FROM BELOW www.stcny.
STEP 7 Installing the Upper Roof Panels Remove protective plastic from both sides of upper roof panels (15,16,17). Place side to face toward the sun facing out when installing. Components 7.A Slide upper roof panels (15,16,17) into their positions as shown. Roof panel (15) Roof panel (16) Roof panel (17) Screw (31) Plastic Sleeve (32) x4 x4 x2 x2 x2 10 15 7.B 15 17 16 16 Fasten roof panel (17) to roof top plate (18) with screws (31), using plastic sleeve (32) as shown.
STEP 8 Installing the Lower Roof Panels Remove protective plastic from both sides of lower roof panels (19,20,21). Place side to face toward the sun facing out when installing. 8.A Components Slide lower roof panels (19,20,21) into their positions as shown. Roof panel (19) Roof panel (20) Roof panel (21) x4 x4 x2 Screw (30) x 10 19 20 21 19 8.B 20 Fasten roof panels (19,20) to connectors (7) with screws (30). 20 21 19 20 19 20 19 20 19 www.stcny.
STEP 9 Installing the Roof Gable Covers Slide upper end of profiles (13, 14) under roof top plate (10) as shown and lower the profiles to fit into roof gable profiles (11, 12). Components 10 13 13 14 13 14 14 Roof gable cover (13) 2171mm Roof gable cover (14) 1584mm Screw (28) End Cover (26) x4 x6 x 34 x 10 From below the gazebo roof, fix roof gable covers (13,14) to roof gable profiles (11,12) using screws (28) through pre-drilled screw holes at mid point and end of profiles.
Gazebo GZ620LS Assembly Instructions WARRANTY: Warranty covers damage due to manufacturing defects only. Warranty does not cover weather inflicted damage (Force Majeure) and/or damages caused by not following assembly instructions and adhering to warnings in manual. ATTENTION: Roof profiles, roof panels and gables must be aligned properly during assembly to minimize any possibility of leaking. EasyGrow 8’x 12’ Greenhouse Visit: http://www.stcny.
