Gazebo GZ3582 Aluminum Composite Roof Panels Assembly Instructions Paragon Group USA , n @O 2rorgoroioorsompany Customer 782 4482
Introduction Thank you for purchasing the Gazebo GZ3582. When properly assembled and maintained, this gazebo will provide many years of enjoyment! These instructions include helpful hints and important information needed to safely assemble and properly maintain the gazebo. Please read these instructions completely before you begin. Our patented gazebo has been designed for easy assembly. All steps can be completed by a team of four people. The assembly should take about two hours.
Safety Advice * The gazebo must be positioned and fixed on a flat level surface. ¢ Dispose of all plastic bags safely. Keep them out of the reach of children. * Keep children and pets away from the assembly area unfit the work is completed. ¢ Always wear shoes, gloves and safety goggles when working. * Take special care not fo touch overhead power lines with the aluminum profiles. ¢ Do not attempt to assemble the gazebo in windy or wet conditions.
List of Parts The gazebo is shipped in three cartons. These cartons are heavy. Be careful when lifting them. Wear proper safety gear inclusiveness shoes, gloves and goggles. The parts are identified by removable stickers. Place all the parts for each step in staging areas, checking that you hate all parts as you go. If any parts are missing or damaged, contact customer service before beginning assembly: Customer 782 4482 No. Gy Sieve [ No. Part 41|10 /X_ N}Eflm 3 22N ! 4 2120mm ; 4 21212 \ 2 1547mm 1486mm 12
STEP 1 Assembling the Corner Profiles Place all the parts on a elev! surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly ta ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. m : Components | Place corner profiles (1) parallel to each other on the ground. Slide support plates (2) into @ comer profiles from the end with a single / screw hole, as shown.
STEP 2 Assembling the Roof Profiles Place all the parts on a level surface. Make sure the pieces are in the correct positions ] before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safely gear including work shoes, gloves and goggles. Components Insert end of long roof profile (3) into long roof profile (4) as shown. Fasten with screws (24). =3 Roof pmme(4) h Repeat to make two chefs. & %fl Crow (24) Roof prom.
STEP 3 Attaching Roof Profiles to Corner Profiles Attach long roof profile sets (3,4) fo corner profiles (1} as shown. Fastest with screws (20). Repeat fo make fwo chefs. mAfluchshonroofproflle sets (5,6) fo corner profiles (1) s shown a ) Fasten with screws (20).
STEP 4 Attaching the Upper Roof Profiles and Roof . Connectors to Roof and Corner Profiles Root Supercomputer it connector u mnnsdor(s) u colonnade) Roof overmanned) mm:m%) x 90 x4 \wmm \W Fasten wnh screws (24), attaching U connectors (8) at same time, as shown. Slide ends of parts (10) through slits in profiles from inside gazebo and fasten with screws (24).
Attach one support connector (30) and one support connector (31) fo each corner post (1) at per-drilled screw holes, using two screws (24) each. Slide support bars {28) onto support connectors {30) and fasten with two screws (24). Attach upper end of support bars (28} to roof profiles fasten with two screws {24). Slide support bars {29) onto support connectors {31) and fasten with two screws (24). Attach upper end of support bars (29) fo roof profiles fasten with two screws (24).
STEP 5 Securing the Gazebo to the Ground Fasten the gazebo frame to the ground, using three spikes (39) for each support plate. Components ~— Ground spike (39) x12 Optional Securing the Gazebo to a Concrete Floor or Wood Deck Concrete Floor: 1. Using an electric concrete drill, drill holes into the concrete floor, corresponding to the holes in the support plates. 2.Insert concrete screws (40) lino the holes and hammer into place, using a mallet. 3. Fasten concrete screws with washers and nuts.
STEP & Installing the Low Roof Gable Profiles ATTENTION: DO NOT ATTEMPT TO ASSEMBLE THIS ALONE | Components mfib&a Top center Roof profile steel Roof Top Profligacy Propels i lo(14) Cuvier) ))D» Browser) Escrows) Nm Mma) Hooke) Using at least three people, install the roof gables (11,12,13,14) in the following order ATTENTION: : : Roof Profiles,roof panes and gables must be aligned properly during assembly ¢ fo minimize any possibility > E of leaking.
Using screws (25) and nuts (33), connect roof gable profiles (11) to roof connectors on top of corner profiles (1). == Using screws (24), connect roof corner connector (10) o roof gable profile (11). Using screws roof gable profile (11) to roof top connector beam (22) as shown. m i Using screws (24) connect fop center connector {19) to top connector beam (22). Install roof gable profiles {12). Using screw (32) attach roof profile steel end cap {44) on roof profile {12).
L% Connect the roof top cover {21) to the roof top connector beam (22) as shown. First connect the two U-shaped connectors(23) to the roof fop cover four screws (24). Then attach Shaped connectors (23} o roof top connector beam (22} from below, using four screws (26). Attach Y-connectors (43) to underside of roof gable profiles using screws (24) as shown, Connect profiteer] 3,14) fo Y-connector (43) and the other end to U-connector (8) using screws (25) and nuts (33).
STEP 7 Installing the Roof Panels and Upper Roof Profiles IMPORTANT: Pertly cul on the edge of the panels on both side with knife and remove protective plastic of roof panels. Place with black surface toward the sun facing out when installing. [Components side Roof Panel(15) Roof Panel(17) Roof Panel(16) Roof Paneling) Screw(32) Fit roof panel (15} on top of roof profiles ('Undersigned. e P A IMPORTANT Gently cvi the film in order £ o ovoid breaking on the panel.
Fit roof panel {16) on fop of roof profiles {11,14) as shown Fit roof panel {16} on top of roof profiles {11, 14} as shown and fasten with one screw {32} outer roof connector { 7).
[Components Roof Gable Profile Roof Gable Profile Roof Gable Profile Screw(32) (11A) (13A) (14A) Place roof profile {14 A) on top of roof profile (14} as shown and fasten with screws (25) from below (inside gazebo).
Fit roof panel (18) on top of roof profiles (13,14) and fasten with one screws (32) outer roof connector (7). Place profiles (11A) on top of roof profile {11) ; fasten ONLY THE TOP END with 1 screw (25). Fit roof panel {17) on top profiles (11,13] , fasten with one screw {32) outer roof connector (7), and then fasten {11A} with screw (25).
Continue in a clock-wise direction as shown. Place the roof panel [16,17) on top of profiles {11,13,14) , fasten with screw (32) from below.
Place the roof gable profile (13A) on top of (13}, fasten with screw (25Yfmm below of 13. Components ] Plastic Gap #1 {37) Plastic Cop #2 (38) x8 x4 Close off roof profiles {13,14) with plastic caps #1 (37) and roof profiles {11) with plastic caps #2 (38).
Gazebo GZ3582 Aluminum Composite Roof Panels Assembly Instructions /\ WARNING: Cancer and Reproductive Harmwww.P65Warnings.ca.gov. /\ ADVERTISEMENT: Cancer et Troubles de I apparel reproducteurwww.P65Warnings.ca.gov. /\ INADVERTENCE: Cancer y Dario Reproductivowww.P65Warnings.ca.gov. WARRANTY: Warranty covers damage due to manufacturing defects only for a period of 5 years on the structure, and 5 years on the Aluminum Shell from date of purchase.