深圳市乾朗能源科技有限公司 第 1 页 共 12 页 Specification For Approval 客户承认书 Customer(客户名称): Battery model name(电池型号)QL401015 Customer model number(客户料号): Revision(版本) : A0 Date(日期) : 2022-06-24 Customer approval(客户承认) Comment (备注): Customer’s signature/ Date(客户签名/日期) : Prepared 制定 Checked 审核 Approved 批准 陈军 杨英 邵利红
深圳市乾朗能源科技有限公司 第 2 页 共 12 页 Content 目录 1. Scope 3 适用范围 2. Model: QL401015 3 编码规则 3. Dimensions of battery pack 3 电池组尺寸 4. Specifications of battery pack 4 电池组规格 5. Specification of cell 4 电芯规格 6. Battery Cell Performance Criteria 5 电池性能检查及测试 7. Required Protection Functions保 7 护功能要求 8.
深圳市乾朗能源科技有限公司 第 3 页 共 12 页 1.Scope This document describes the Product Specification of the Lithium-Polymer (LIP) rechargeable battery cell supplied by QIANLANG Corporation Limited). 适用范围 本规格说明书描述了深圳市乾朗新能源科技有限公司(以下简称乾朗新能源)生产的可充电聚合物锂离子电池 的产品性能指标 2.Model:QL 401015 型 号:QL 401015 PCM—保护板 3.Dimensions of battery pack 电池成品尺寸 T: ≤4mm * W: ≤10mm * L≤15mm Ltems 项目 Description 类型 Dimension and Spec 尺寸和规格 T Thickness 厚度(不含胶纸) 4.0mm Max W Width 宽度(双这边) 10.0mm Max L Length(Withour sealant)电芯长度 (不含极耳胶) 15.
深圳市乾朗能源科技有限公司 第 4 页 共 12 页 1.2±0.1mm 15±1mm Red: connect to “+” 红色接正极 Black : connect to ground “ ——- ” 3.7V 2206 401015 0.148Wh Connecting Wires 接线方式 -QL + 40mAh 黑色接负极 4. Battery configuration 电池组成 4. Specifications of battery pack NO ltem criteria 电芯型号 Semi-manufactured cell QL401015 2 保护板(PCM) DW01+8205A 3 线材/接头(Wire/connector) 左出线 外漏 15±1mm Remarks 普通板 1571# 线径 0.
深圳市乾朗能源科技有限公司 第 5 页 共 12 页 电池组规格 No. Item Specifications 4.0 组装方式 单节 4.1 Capacity(容量) 40mAh 4.2 Impedance(内阻) ≤350m(加板后)常温 25℃ 4.3 Dimensions (mm) (尺寸) ≤4(T) * ≤10.0(W) *≤15.0(L) (mm) 4.4 Weight (g) (重量) 约 1.05g 4.5 Overcharge protection voltage (过充保护电压) 4.25V 4.6 Max. charge current (最大充电电流) 1C 4.7 Over discharge protection voltage (过放保护电压 2.5V 4.8 Max discharge current (最大放电电流) 1.0C 4.9 Charge temperature (充电温度) 0℃ ~ +55℃ 4.
深圳市乾朗能源科技有限公司 第 6 页 共 12 页 5. Specifications of cell 电芯规格 NO. 1 2 3 Items Charge voltage 充电电压 Nominal voltage 标称电压 Nominal capacity 标称容量 Typical capacity 典型容量 Specifications 4.2V 3.7V 40mAh 0.2C Discharge (0.2C 放电) 40mAh@0.2C Discharge 4 Charge current 充电电流 Standard Charging:: 0.2C 标准充电: 0.2C Rapid charge: 1.0C 快速充电: 1.0C 5 Standard Charging method 标准充电方法 0.2C CC(constant current)charge to 4.2V,then CV(constant voltage 4.2V)charge till charge current decline to ≤0.02C 0.2C CC(恒流)充电至 4.
深圳市乾朗能源科技有限公司 第 7 页 共 12 页 6.Battery Cell Performance Criteria 电芯性能检查及测试 6.1 Electrical characteristics 充放电性能 O. Items Rated Capacity Test Method and Condition Charging the cell initially with constant current at 0.2C and then with constant voltage at 4.2V till charge current declines to 0.02C 先用 0.2C 恒流充电至 4.2V,再恒压 4.2V 充电直至充电电 流≤0.02C The capacity means the discharge capacity of the cell, which is measured with discharge current of 0.2C with 2.75V cut-off voltage after standard charge.
深圳市乾朗能源科技有限公司 第 8 页 共 12 页 6.2 Mechanical characteristics 机械特性 NO. 1 2 Items Test Method and Condition Criteria Vibration Test 振动测试 After standard charging, fixed the cell to vibration table and subjected to vibration cycling that the frequency is to be varied at the rate of 1Hz per minute between 10Hz and 55Hz, the excursion of the vibration is 1.6mm.The cell shall be vibrated for 30 minutes per axis of XYZ axes. 将标准充电后的电池固定在振动台 上,沿 X、Y、Z 三个方向各振动 30 分 钟 , 振 幅 1.
深圳市乾朗能源科技有限公司 第 9 页 共 12 页 7. PCM parameter PCM 参数 7.1 PCM 参数 序号 项目 过充电检测电压 4.1 VDET1 过充保 过充电检测延迟时间 tVDET1 护 过充电解除电压 过放电检测电压 过放保 4.2 护 过放电检测延迟时间 过放电解除电压 过电流检测电压 4.3 符号 过流保 护 过电流保护电流 检测延迟时间 4.4 短路保 护 检测延迟时间 4.5 内阻 主回路通态电阻 VREL1 VDET2 tVDET2 VREL2 VDET3 IDP tVDET3 TSHORT 保护解除条件 消耗电 通常工作时消耗电流 流 静态电 4.7 休眠时消耗电流 流 识别电 4.8 T 端电阻值 阻 4.10 码片 S 端电阻值 码片数据类型 锂电保护板测试仪 ROM 最小值 4.275 锂电保护板测试仪 检验标准 典型值 最大值 4.3 单 位 4.325 200 V ms 锂电保护板测试仪 4.05 4.1 4.15 V 锂电保护板测试仪 2.3 2.4 2.
深圳市乾朗能源科技有限公司 第 10 页 共 12 页 序号 物料名称 物料代号 物料规格 用量 1 保护 IC U1 DW01/SOT23-6 1 德普威 2 MOSFET U2 8205A/SOT23-6 1 德普威 3 贴片电阻 R1 100Ω ±5%/0603 1 华新科 4 贴片电阻 R2 1KΩ ±5%/0603 1 华新科 6 贴片电容 C1 1 华新科 7 镍片 B+/B- 5.0*3.0*0.3 2 XBL 8 底板尺寸 6*3.5*0.6mm 1 佳万通达 备注: 板长公差+/-0.1mm 0.1uF -20%/+80%25V/0402 板宽公差 +/-0.1 7.3 Application Schematic 应用原理图 8. Packaging、 Storage and Transportation 包装、储存及运输 8.
深圳市乾朗能源科技有限公司 第 11 页 共 12 页 X2 吸塑盘 小白盒 外箱 8.2 Storage 储存: 8.2.1 The Li-ion battery pack should be stored in a cool, dry and well-ventilated area, and should be far from the fire and the high temperature. 锂电池需保存在阴凉,干燥,通风的环境中,避免接触火源与热源。 8.2.2 The battery should store in the product specification book stipulation temperature range, the best storage temp. is 0 to 25℃. The best humidity is 60±25%. 电池需按规格书规定温度范围进行储存,最佳储存温度为 0 到 25℃,最佳湿度为 60±25%。 8.2.
深圳市乾朗能源科技有限公司 第 12 页 共 12 页 8.3.4 The highest temperature in transportation is lower than 65℃. 最高运输温度不超过 65℃。 9. Use Attentions 使用注意事项: To ensure proper use of the battery please read the manual carefully before using it. 为确保电池正确使用,请在使用之前阅读使用说明书。 9.1 Warnings 警告: 9.1.1 Do not expose to, dispose of the battery in fire. 不可将电池置于火中。 9.1.2 Do not put the battery in a charger or equipment with wrong terminals connected. 不可将电池充电器正负极反接。 9.1.3 Avoid shorting the battery. 不可将电池短路(P+、P-) 。 9.1.
深圳市乾朗能源科技有限公司 第 13 页 共 12 页 9.2.8 The battery must be stored after charged, and should be charged and discharged once every 3 months. 电池必须带电储存,并且每三个月进行充放电一次。 9.3 Discharge 放电: 9.3.1 The discharging current should not surpass the biggest discharging current this specification book stipulation, The large discharge current can cause heat and lower capacity. 放电电流不可超过规格书最大额定放电放电电流。大电流会导致电池发热和容量降低。 9.3.
深圳市乾朗能源科技有限公司 第 14 页 共 12 页 9.5 Disposal 处理措施: Regulations vary for different countries. Dispose of in accordance with local regulations. 不同国家有不同规定。 请按当地规定进行处理。 9.6 Note: Any other items which are not covered in this specification shall be agreed by both parties.