User manual

ManualsBrandsPANASONIC ManualsIP CCTV Systemsi-Pro Extreme LAN IP CCTV camera 1920 x 1080 pix

WV-S2131L

PGQX2085XAavs1016-2116Printed in China

Preparations

Installation method

Description of

installation method

Mount the camera on the two-gang junction box using the attach-

ment plate (accessory).

【Type 1】

Directly mount the camera onto the ceiling or wall using the attach-

ment plate (when wiring can be installed in the ceiling or wall).

【Type 2】

Mount the camera in the ceiling using WV-Q174B ceiling mount

brackets (approx. 280 g {0.62 lbs}).*

Refer to the Instruction

Manual provided with the

WV-Q174B.

When mounting the camera on an insufﬁ ciently strong ceiling using

the WV-Q105A ceiling mount brackets

(approximately 150

g {0.33 lbs})

Refer to the Instruction

Manual provided with the

WV-Q105A.

The following notations are used when describing the functions limited for specified models.

The functions without the notations are supported by all models.

S2131L

:The functions with this notation are available when using the model WV-S2231L / WV-S2131L

/ WV-S2131.

S2130

:The functions with this notation are available when using the model WV-S2130 / WV-S2110.

S2111L

:The functions with this notation are available when using the model WV-S2211L / WV-S2111L.

Auxiliary handle

MONITOR OUT

conversion plug

External I/O terminal

plug

Power cord plug

Step 2 Remove the enclosure from the camera.

【１】Remove the enclosure and

cushion from the camera.

【2】Remove the power cord plug

(accessory) and the external I/O

terminal plug (accessory)

attached to the camera.

S2131L

S2111L

Step 1 Fixing the attachment plate *There are 2 methods to install the camera to a ceiling or wall.

【

Type 1

】

Mount the camera on the two-gang junction box using the attachment

plate (accessory)

Align the FRONT direction of the template A (accessory) with the desired direction, and

drill through a 25.4 mm {1 inch} diameter hole to attach the attachment plate. Then, the

direction of the marker “FRONT⇩” on the camera (see the figure in [3] of “Step 4 Mount

the camera”) should face the desired direction of the camera.

If the mounting direction of the camera is not determined yet or if you want to change

the direction of the camera after it has been installed

If you want to be able to change the direction of the camera, drill through a 73 mm {2-7/8 inches} diame-

ter hole in the center. By doing so you can adjust the mounting direction of the camera in 90° increments.

46 mm

83.5 mm

FRONT

25.4 mm

{ø1 inch}

73 mm

{

2-7/8 inches}

83.5 mm

{3-9/32 inches}

46 mm

{1-13/16 inches}

*1 When using WV-Q174B camera ceiling mount bracket, if the built-in

microphone port is blocked by the cover of bracket, the collectable

volume may decrease and the sound of attic is likely to be collected

by mistake. Therefore, please conﬁ rm the installation conditions

before use.

S2130

WV-S2131L

Built-in microphone port

Network Camera

Model No. WV-S2131L / WV-S2131 / WV-S2130

WV-S2111L / WV-S2110

WV-S2231L / WV-S2211L

Installation Guide

Included Installation Instructions

For U.S. and Canada:

Panasonic System Communications

Company of North America,

Unit of Panasonic Corporation

of North America

www.panasonic.com/business/

For customer support, call 1.800.528.6747

Two Riverfront Plaza, Newark, NJ 07102-5490

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga,

Ontario, L4W 2T3 Canada

(905)624-5010

www.panasonic.ca

For Europe and other countries:

Panasonic Corporation

http://www.panasonic.com

Panasonic System Networks Co., Ltd.

Fukuoka, Japan

Authorised Representative in EU:

Panasonic Testing Centre

Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, Germany

Panasonic System Networks Co., Ltd. 2016

Important safety instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9) Only use attachments/accessories specified by the manufacturer.

10) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury

from tip-over.

S3125A

11) Unplug this apparatus during lightning storms or when unused for long periods of time.

12) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been dam-

aged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally,

or has been dropped.

Troubleshooting

Open Source Software

󱾀 This product contains open source software licensed under GPL (GNU General Public License),

LGPL (GNU Lesser General Public License), etc.

󱾀 Customers can duplicate, distribute and modify the source code of the software under license of

GPL and/or LGPL.

󱾀 Refer to the “readme.txt” file on the provided CD-ROM for further information about open source

software licenses and the source code.

󱾀 Please note that Panasonic shall not respond to any inquiries regarding the contents of the source

code.

The model number and serial number of this

product may be found on the surface of the unit.

You should note the model number and serial

number of this unit in the space provided and

retain this book as a permanent record of your

purchase to aid identification in the event of

theft.

Model No.

Serial No.

NOTE: This equipment has been tested and found

to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference when the

equipment is operated in a commercial environ-

ment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed

and used in accordance with the instruction man-

ual, may cause harmful interference to radio com-

munications.

Operation of this equipment in a residential area is

likely to cause harmful interference in which case

the user will be required to correct the interfer-

ence at his own expense.

FCC Caution: To assure continued compliance,

(example - use only shielded interface cables

when connecting to computer or peripheral devic-

es). Any changes or modifications not expressly

approved by the party responsible for compliance

could void the user’s authority to operate this

equipment.

For U.S.A.

CAN ICES-3(A)/NMB-3(A)

For Canada

WARNING:

• To prevent injury, this apparatus must be secure-

ly attached to the wall/ceiling in accordance with

the installation instructions.

• To prevent fire or electric shock hazard, do not

expose this apparatus to rain or moisture.

• The apparatus should not be exposed to drip-

ping or splashing.

• All work related to the installation of this product

should be made by qualified service personnel

or system installers.

• The installation shall be carried out in accor-

dance with all applicable installation rules.

• The connections should comply with local elec-

trical code.

• Batteries (battery pack or batteries installed)

shall not be exposed to excessive heat such as

sunlight, fire or the like.

CAUTION:

• Any changes or modifications not expressly

approved by the party responsible for compli-

ance could void the user’s authority to operate

the equipment.

• The network camera is only intended for a con-

nection to an ethernet or PoE network without

routing to the outside plant.

Disposal of Old Equipment and Batteries

Only for European Union and countries with recycling systems

These symbols on the products, packaging, and/or accompanying documents mean that used

electrical and electronic products and batteries must not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them

to applicable collection points in accordance with your national legislation.

By disposing of them correctly, you will help to save valuable resources and prevent any potential

negative effects on human health and the environment.

For more information about collection and recycling, please contact your local municipality.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national

legislation.

Note for the battery symbol (bottom symbol)

This symbol might be used in combination with a chemical symbol. In this case it complies with the

requirement set by the Directive for the chemical involved.

About the user manuals

Product documentation is composed of the following documents.

• Installation Guide (this document): Explains installation, mounting, cable connections, and adjusting the

ﬁ eld of view. This manual uses the WV-S2111L as an example in the explanations.

• Important Information (included in the CD-ROM):

Provides basic information about the product.

• Operating Instructions (included in the CD-ROM): Explains how to perform the settings and how to

operate this camera.

Adobe

Reader

is required to read these operating instructions on the provided CD-ROM.

When the Adobe Reader is not installed on the PC, download the latest Adobe Reader from the Adobe web site

and install it.

The external appearance and other parts shown in this manual may differ from the actual product within the

scope that will not interfere with normal use due to improvement of the product.

About notations

Standard accessories

Installation Guide (this document) ........................1 set

IMPORTANT SAFETY INSTRUCTIONS ............... 1 pc.

Warranty card*

...................................................1 set

CD-ROM*

.......................................................... 1 pc.

Code label*

........................................................ 1 pc.

*1 This product comes with several types of warranties. Each warranty is only applicable to the products pur-

chased in the regions indicated on the relevant warranty.

*2 The CD-ROM contains the operating instructions and different kinds of tool software programs.

*3 This label may be required for network management. Use caution not to lose this label.

The following parts are used during installation procedures.

Attachment plate ................................................ 1 pc.

Template A (for the attachment plate)

......................1 sheet

Power cord plug*

............... 1 pc.

External I/O terminal plug*

............................................... 1 pc.

MONITOR OUT conversion plug ......................... 1 pc.

Auxiliary handle .................. 1 pc.

Bit (WV-S2231L/WV-S2211L only)

(Hex wrench, screw size 6.35 mm {1/4 inches} T10)

.... 1 pc.

S2131L

S2111L

S2131L

S2111L

S2130

S2131L

S2111L

*4 The external I/O terminal plug and power cord plug are attached to the camera.

Prepare the required parts for each installation method before starting the installation. The following

are the requirements for the various installation methods.

IMPORTANT:

󱾀

Procure 4 screws (M4) to secure the attachment plate (accessory) to a ceiling or a wall.

󱾀

The minimum required pull-out capacity of a single screw or anchor bolt is 196 N {44 lbf} or

more when mounting with the installation method

【

Type 1

】

【

Type 2

】

described in the

right table.

󱾀

Select screws according to the material of the location that the camera will be mounted to.

In this case, wood screws and nails should not be used.

󱾀

If the mounting location such as plaster board is too weak to support the total weight, the

area shall be sufficiently reinforced.

Installation

Step1

Fixing the attachment

plate

Step2

Remove the enclosure

from the camera.

Step3

Making connections

⇨

Step5

Adjustment

⇨

Step4

Mount the camera

⇨

Step6

Configure the network

settings

⇨

󱾀Remove the camera using the reverse order of the installation procedures.

The installation tasks are explained using 6 steps.

【

Type 2

】

Directly mount the camera onto the ceiling or wall using the

attachment plate (accessory).

46 mm {1-13/16 inches}

83.5 mm {3-9/32 inches}

Two-gang junction box

Attachment plate (accessory)

Fixing screws for attachment plate: x4

(M4, locally procured)

Attachment plate (accessory)

Fixing screws for

attachment plate: x4

(M4, locally procured)

Enclosure

External I/O

terminal

plug

Power

cord

plug

WV-S2231L / WV-S2211L

󱾀Do not remove the auxiliary wire.

Using the side cable access hole

When installing the camera directly on the ceiling or wall with cables exposed, or when mounting

the camera using the ceiling mount bracket WV-Q174B (option), cut out a portion of the dome

cover to open a cable access hole.

IMPORTANT:

󱾀

To prevent injuries and protect the cables, finish the side cable access hole with a file

to avoid sharp edges.

Side cable access hole

Before requesting service, refer to the Important Information (included in the CD-ROM) and

“Troubleshooting” in the Operating Instructions (included in the CD-ROM) and confirm the

trouble.

Cushion

Bit

: Direct current symbol

Note:

󱾀

Attach the attachment plate (accessory) so that the marking (PGYE1054) faces toward the

ceiling or wall to be installed.

【

Common

】

󱾀 Before attempting to connect or operate this product, please read these instructions carefully and

save this manual for future use.

󱾀 For information about the basic description of this product, refer to the Important Information on

the provided CD-ROM. For information about how to perform the settings and how to operate the

camera, refer to the Operating Instructions on the provided CD-ROM.

󱾀 The model number is abbreviated in some descriptions in this manual.

: Hot surface symbol

Summary of content (2 pages)

PAGE 1
For U.S.A. WARNING: Installation Guide Included Installation Instructions Network Camera Model No. WV-S2131L / WV-S2131 / WV-S2130 WV-S2111L / WV-S2110 WV-S2231L / WV-S2211L The model number and serial number of this product may be found on the surface of the unit. You should note the model number and serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft.
PAGE 2
【3】If needed, connect a powered speaker to the audio output connector. Step 3 Making connections S2131L S2111L ■Refer to the Important Information on the provided CD-ROM for details about each cable. Note: As necessary, use a cable tie (locally procured) to tie the cables together. Route the power cable as shown in the following illustration, and do not clip the power cable when mounting the enclosure.