Ceiling Mount Bracket Operating Instructions WV-Q155C WV-Q155CE WV-Q155S WV-Q155SE Model No. Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual.
CONTENTS Preface ....................................................................................................................................... 2 Precautions ................................................................................................................................ 2 Major Operating Controls and Their Functions .......................................................................... 4 Installations ..............................................................................
• Select an installation area that can support the total weight. If a selected area is too weak to support the total weight, a fall of the product may occur resulting in injury. Installation work shall be started after sufficient reinforcement. • Periodic inspections shall be conducted. Rust on the metal parts or screws may cause a fall of the product resulting in injury. Consult the dealer for the inspections. • Do not rub the edges of metal parts with your hand. Failure to observe this may cause injury.
Major Operating Controls and Their Functions Mounting base Camera mounting plate Fixing screw to be used for cover fall prevention Hole for microphone cable Microphone stand* Decorative cover Dome cover * If a microphone is used, mount the microphone on the rubber-made microphone stand. Unless the microphone is used, cut the rubber with a nipper or conduct another treatment.
Installations Be sure to read "Precautions" before installation. The Installation Guide of the network camera shall be read as well. 1. Remove the decorative cover. q Loosen the fixing screw (unremovable) to be used for cover fall prevention. Fixing screw to be used for cover fall prevention w Unhook the decorative cover from the hooks (3 positions) of the camera mounting plate and remove the decorative cover by turning it counterclockwise. e Take the inner cover out.
3. Put Template A (accessory) against the ceiling and make a hole. q Make 4 holes of 12 mm {1/2"} in diameter. w Remove the center part from the template. e Make a hole of 160 mm {6-5/16"} in diameter. ø12 mm {1/2"} (4 positions) Ceiling face ø160 mm {6-5/16"} * The hole shape is shown below. Template A 4. Install two anchor bolts (M10 recommended) into the concrete ceiling. q Determine the anchor bolt length by use of Template B (accessory). w Position the nut by use of Template B (accessory).
5. Mount the safety wire angle (accessory) on the 2nd anchor bolt and connect the safety wire (accessory) to the angle. Upper side q Disconnect the safety wire from the Anchor bolt Mark w safety wire angle. w Engage the face marked q with the w Insert e Bend anchor bolt. q Disconnect e Bend the face marked w. r Connect the safety wire to the safety wire angle again.
7. Insert the mounting base into the hole made in Step 3. 8. Secure the mounting base to the ceiling board with the ceiling board fixing screws (4 positions). q Engage the top of the mounting base with the 1st anchor bolt. w Secure the mounting base by turning the ceiling board fixing screws clockwise. Turning the ceiling board fixing screws clockwise provides ceiling board tightening between the bottom of the mounting base and ceiling board fixing bracket resulting in mounting base securing.
10. Install the inner cover. Slide the covers located on the both lateral sides of the camera and put the inner cover on the camera until the hooks inside the inner cover are held in the holes of the camera (until a click is heard). Important: Put the inner cover down on the camera until the outside cover of the camera cannot be seen from the opening (from which the camera lens is visible) of the inner cover.
11. Mount the camera on the camera mounting plate. q Put the camera onto the camera mounting plate with aligning the lock plate of the camera with the guide of the camera mounting plate and aligning the center of the camera mounting plate with the center of the screw for tripod mounting, and turn the camera clockwise. w Secure the camera with 1 piece of the camera fixing screw (supplied with the camera). (Recommended tightening torque: 0.68 N·m {7.
CK LO Align A with A FRON T FRONT END Mounting base Align B with B START 14. Mount the camera mounting plate on the mounting base. q Align the marks (A to A and B to B) between the camera mounting plate and mounting base. w Mount the camera mounting plate on the mounting base with aligning g of the camera mounting plate with "STARTh" of the mounting base. e Turn the camera mounting plate until g of the camera mounting base aligns with "ENDh" of the mounting base.
Specifications Ambient temperature: Dimensions: Mass: Finish: –10 °C to + 50 °C {14 °F to 122 °F} 185 mm {7-5/16 inches} in diameter x 145 mm {6-7/16 inches} in height Approx. 800 g {1.77 lbs} Main body: Treatment steel Decorative cover: ABS resin with silver metallic coating Dome cover: Acrylic resin Standard Accessories Operating Instructions (this book) ............................. 1 pc. The following are for installation Safety wire .................................................................
