System Controller Operating Instructions WV-CU360C ENGLISH Model No.
ENGLISH VERSION Caution: Before attempting to connect or operate this product, please read the label on the bottom. For U.S.A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 8) Do not use near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.
CONTENTS IMPORTANT SAFETY INSTRUCTIONS ............................ PREFACE .......................................................................... FEATURES ........................................................................ PRECAUTIONS ................................................................. MAJOR OPERATING CONTROLS & THEIR FUNCTIONS .... ■ Rear View & AC Adapter ............................................ INSTALLATIONS ...............................................................
PREFACE The System Controller WV-CU360C is designed for setup and operation of cameras and other system units installed in a surveillance system. The controller is compatible with the Panasonic Security Data (PS • Data) protocol by default, but DIP switches are provided to select the conventional communication protocol used with the Video Multiplexer WJ-FS616C, Matrix Switcher WJ-SX350 or WJ-SX850.
MAJOR OPERATING CONTROLS & THEIR FUNCTIONS ■ Rear View and AC Adapter q 78 901 r t 456 RISQUE DE CHOCS ELECTROUES NE PAS OUVRIR e 23 RISK OF ELECTRIC SHOCK. DO NOT OPEN w CONTROLLER No. MODE DATA DC 9V IN y DC 9V IN q Controller Number Switch (CONTROLLER No.) This switch is used to assign a controller number to the System Controller to identify it in a system comprising multiple System Controllers (See page 14). A system may comprise up to four controllers.
INSTALLATIONS ■ Template Mounting The system controller is provided with four templates including one for PS • Data system that is placed (not taped yet) on the surface of the controller when shipped from the factory.
■ Rear Panel Switch Setting (Summary) An 8-bit DIP switch and a rotary switch mounted on the rear of the controller specify the system unit ID and parameters for communication. Switch settings depend on your system configuration such as a PS • Data system, WJ-FS616C Multiplexer system, WJ-SX350 Matrix Switcher system or System 850. A summary of switch positions is shown below. For detailed information refer to the description of switch settings provided for each system. System Controller No.
Panasonic Security Data (PS • Data) Systems 9
MAJOR OPERATING CONTROLS & THEIR FUNCTIONS ■ Front View (Template for PS • Data) q w e OPERATE LOGIN ALARM r t MONITOR UNIT CAMERA y u i BUSY PROHIBITED System Controller WV-CU !8 !9 @0 @5 PROGRAM SETUP CAM SETUP IRIS CLOSE SHIFT FUNCTION CAM FUNCTION ALM RESET ALM SUSPEND #0 #1 OPEN UP IRIS RESET AUTO UNIT A ALM RECALL B/W UNIT VCR CAM MULTI SCREEN SELECT DEF FOCUS NEAR @6 @7 @8 @9 360C L UNIT B AUX 2 STILL EL-ZOOM FAR AUTO FOCUS ZOOM WIDE WIPER R TELE DOWN – +
o Iris buttons (IRIS, CLOSE/OPEN) Close or open the lens iris of cameras equipped with the specified lens. When these buttons are pressed simultaneously, the lens iris is reset to the factory default setting. !0 Focus buttons (FOCUS, NEAR/FAR) Adjust the lens focus of cameras equipped with the specified lens. When these buttons are pressed simultaneously, the lens focus is set automatically if the specified camera is used.
@2 Defroster/Auxiliary 2 button (DEF/AUX 2) Activates the housing defroster of cameras provided with this feature. Pressing this button in the shift mode will turn on the AUX 2 function controlling accessories connected to the cameras or the system. The LED next to the button is lit while the defroster or AUX 2 function operates. @3 Wiper/Auxiliary 1 button (WIPER/AUX 1) Activates the housing wiper of cameras provided with this feature.
INSTALLATIONS (PS • Data) CAUTION The installation should be made by qualified service personnel or system installers according to the following instructions. ■ System Connections ● Connection Example Example 1 shows 8 cameras connected to 2 Data Multiplex Units (WJ-MP204C), to a Video Multiplexer (e.g., WJ-FS316) and a Digital Disk Recorder (e.g., WJ-HD100). The WV-CU360C controls these system units through RS-485 communication while pictures are viewed on the monitors. Camera No. 5 Camera No.
Example 2 shows 4 Data Multiplex Units connected with 16 combination cameras, and 4 System Controllers. 4 cameras can be connected to one Data Multiplex Unit Channel 1 Channel 2 Channel 4 Channel 13 Channel 14 Channel 16 Up to 4 Data Multiplex Units WJ-MP204C Data Multiplex Unit WJ-MP204C Unit address 1 Data Multiplex Unit WJ-MP204 Unit address 2 Data Multiplex Unit WJ-MP204 Unit address 4 Controller No. 2 Controller No.
• Daisy Chain Connection Video Multiplexer WJ-FS309 (WJ-FS316) Data Multiplex Unit WJ-MP204C System Controller WV-CU360C DATA DATA DATA Termination: ON Termination: OFF Termination: ON Branch Cable RS-485 Cable RS-485 Cable ■ DIP Switch Setting (PS • Data) An 8-bit DIP switch mounted on the rear panel specifies the communication mode, etc. The default position is marked with an asterisk *.
● MODE Switch Setting for System Example 2 ■ Controller Number Setting (PS • Data) The MODE switch needs to be set prior to operating a system connected as shown in Example 2. A 10-position rotary switches provided on the rear for specifying the unit number of the WV-CU360C controller in a PS • Data system. ON 2 3 4 5 6 7 8 Bit 3 should be set to OFF. Bit 5 should be set to OFF when the controller is placed in an intermediate position, or set to ON when it is connected at the chain end.
CONTROLLER SETUP PROCEDURES (PS • Data) To display the setup menus for the WV-CU360C System Controller on the LED display, set the MODE switch and power up the controller as described below. ■ Prior to Setup ■ Buttons and Controls used for Setup Do the following before entering the setup mode. The following buttons and joystick operations are used in the setup operation. There are three ways to select a parameter, but the following pages only describe the selection by use of the joystick.
■ Setup Menus There are 12 setup menus as shown below.
● Administrator Authorization 1. Press the CAM/SET button while [SEtUP] is displayed. The [- - - - -] prompt appears. ● Parity In this menu, the parity check mode is selected. 1. Display [PrtY] and press the CAM/SET button twice. 2. Enter a password with the numeric buttons, then press the CAM/SET button. The default setting is [12345]. 3. [SPEED] appears when the right password is entered. If password entry failed, the menu returns to [- - - - -].
● Unit A button Assignment ● Unit B button Assignment In this menu, a maximum of 9 system units is assigned to numeric buttons 1-9 regardless of unit address. This is to avoid double-digit unit addresses which can occur in a large system with many units connected and could confuse operators. A frequently used system unit can be easily selected in normal operation by pressing one numeric button and then the UNIT A button.
● Camera Cleaning This menu is for specifying the order in which combination cameras connected to the system are cleaned. The camera cleaning function causes cleaning of the builtin slip rings that conduct electric signals while moving the pan/tilt head. All combination cameras connected to the system are cleaned in the order specified here. Picture viewing is disabled during the cleaning process. 1. Display [CLEAn] and press the CAM/SET button. The LED displays [no-01]. 2.
OPERATING PROCEDURES (PS • Data) ■ Basic Operating Flow The operation starts with a log-in procedure. It proceeds to system unit selection, monitor selection and camera selection. Alarm operations for the system such as alarm reset, suspension may be implemented. The operation ends with a log-out procedure.
■ Login/Logout ● Log In Right after powering up, the controller will be operable without password entry, provided user password certification is set to Off in the setup menu. When set to On, you will be prompted to enter your registered password. The default password is “12345”, but you need to remember the password assigned to you by your system administrator. ESC SET SET Ready for user password entry 1. Insert the DC plug into the DC 9 V IN jack and connect the AC adapter to an AC outlet. 2.
■ System Unit Selection ● Selecting with UNIT A/UNIT B Button Connected system units can be selected either by their unit number (01-99) or by a single-digit number (1-9) assigned to the UNIT A or UNIT B button. The unit numbers (01-99) of some frequently used units can be assigned to numeric buttons 1-9 in the setup. Units can be divided in two groups, one assigned to the UNIT A and the other to the UNIT B button.
■ Monitor Selection ■ Camera Selection A monitor is selected when multiple monitors are connected to a system unit (e.g., a Video Multiplexer) to control such functions as multiscreen display and electronic zoom. One of the cameras connected to the system unit is selected. 1. Select the system unit connected to the monitor you wish to control. 2. Enter a monitor number using the numeric buttons. 1. Select a system unit connected to the camera whose picture you wish to view. 2.
■ Camera Control Cameras and their peripherals are controlled from the WVCU360C as follows. Some of the descriptions may not be applicable if they refer to devices not equipped in your system. The operating procedures on the following pages assume that you have selected a system unit and a monitor. 2. Press the ZOOM TELE button to optically bring the object closer, or press the ZOOM WIDE button to optically widen the scene. ZOOM WIDE TELE 3.
● Combination Camera Shortcuts The shortcuts listed below are available for controlling combination cameras. For more details, refer to the Operating Instructions included with the camera. Function Selecting a PRESET position #1 #10 #64 AUTO PAN ON OFF Speed Up Speed Down Setting Start Point Setting End Point Setting PAN Reverse AUTO MODE MODE Off SEQ On SORT On ENDLESS PAN On Off DIGITAL FLIP On Off PROP.
● Housing/AUX Control ■ Data Multiplex Unit Control When your system includes a camera housing, the defroster and wiper equipped in it are controlled. When a Receiver is installed in the system, an auxiliary device connected to it such as a buzzer or lamp will be also controlled. When more than one Data Multiplex Unit are connected with the controller as shown in System Connection Example 2 on page 14, you can select a camera directly with the camera number, without typing a system unit address.
■ Video Multiplexer Control Some of the major functions equipped in a Video Multiplexer are remotely controlled from the System Controller. For more information, refer to the manual included with the Video Multiplexer. The operating procedures on the following pages assume that you have selected a system unit and a monitor. 8 All cameras still 1. Enter 0 with the numeric buttons, then press the STILL/– button. All camera pictures freeze on the multiscreen while the STILL/– indicator is lit.
● Viewing Playback VCR playback pictures are displayed on the selected spot or multiscreen monitor. 1. With the connected VCR in playback mode, press the VCR/CAM button to turn on the VCR indicator. Playback pictures are displayed on the selected monitor. VCR CAM 4. To move the sequence one step back, press the STILL/– button. STILL – 5. To cancel the sequence pause, press the SEQ PAUSE button again. SEQ PAUSE 2. Press the VCR/CAM button again to cancel viewing playback. The VCR indicator goes off.
■ Digital Disk Recorder Control A Digital Disk Recorder is controlled from the System Controller using shortcuts assigned to numeric buttons. For more information, refer to the manual included with the Digital Disk Recorder. The operating procedures on the following pages assume that you have selected a system unit and a monitor. ● WJ-HD100 Shortcuts The shortcuts listed below are available for controlling a digital disk recorder.
Item WJ-HD100 WV-CU360C Note SETUP DAYLIGHT SAVINGS DAYLIGHT SAVINGS 1 3 SHIFT FUNCTION SETUP Timer REC Mode Selection Operate LCD Button. Button Lock OFF Operate LCD Button. OFF, INT or EXT selectable SHIFT FUNCTION SETUP 3 0 SHIFT FUNCTION SETUP Button Lock ON Operate LCD Button. 3 1 SHIFT FUNCTION ● WJ-HD500A Shortcuts The shortcuts listed below are available for controlling a digital disk recorder.
Item Controller Operation Note SETUP Screen Display ON/OFF SHIFT FUNCTION SETUP Group Selection SHIFT FUNCTION ALM RESET Show/Hide Alarm Log ALM RECALL SHIFT SETUP Skip Playback FWD. SHIFT Speed change 1/2, 1, 2, 5 FUNCTION SETUP Skip Playback REW. SHIFT Speed change 1/2, 1, 2, 5 FUNCTION SETUP Record List 1 line Up SHIFT FUNCTION SETUP Record List 1 line Down SHIFT FUNCTION SETUP Record List Turn Next Page SHIFT FUNCTION SETUP Record List Turn Prev.
Item Controller Operation Note SETUP Copy to DVD SHIFT FUNCTION SETUP Copy Cancel SHIFT FUNCTION SETUP DVD Copy Record Display SHIFT ■ Alarm Operation When the WV-CU360C receives an alarm signal from a system unit, the alarm indicator on the controller blinks. The alarm indicator changes from blinking to steady light when the alarm is automatically reset. The camera number [---] appears in the camera section of the LED display. Equal to EL-ZOOM FUNCTION 2.
REMOTE SETUP of UNITS & CAMERAS You can set up the system unit and the camera with the setup menu by this controller. You can use the controller to set up system units and cameras. This section describes the main remote setup procedures. Some of the descriptions may not be applicable if they refer to devices not equipped in your system. For further information on the default settings and operating procedures, refer to the Operating Instructions included with the individual units.
7. Move the cursor to [SPECIAL] on the Setup menu, and press numeric buttons 4 and 6 simultaneously for 2 seconds or more to display the special menu. 8. Move the cursor to [CAMERA RESET]* on the Setup menu, and press buttons 4, 5 and 6 simultaneously to reset all the functions to the defaults. * The menu to reset the camera functions differs depending on the camera: [SPECIAL] for the WV-CS650, [SPECIAL 2] for the WVCS854, and [END] for fixed cameras etc.
■ Camera Preset Position There are two ways of presetting camera positions. One is to use the camera setup menu of the combination camera and the other is to operate the System Controller as follows. 4. Press the HOME/PRESET/PROGRAM PRESET button while holding down the PROGRAM/CAM SETUP/CAM FUNCTION button. The position and its number are memorized for later recall. 1. Select the desired system unit, monitor and camera. PROGRAM 2. Move the camera to a position you wish to preset, using the joystick.
For WJ-FS616C Multiplexer System 39
MAJOR OPERATING CONTROLS & THEIR FUNCTIONS ■ Front View (Template for WJ-FS616C) q w e OPERATE LOCK ALARM r UNIT t CAMERA System Controller WV-CU 360C For Multiplexer MULTI SCREEN ALT CAMERA SITE CONTROL SPOT IRIS !5!6!7 CLOSE ALM RESET SEQUENCE OPEN UP IRIS RESET VTR CAM AUTO/+ !8!9@0 FOCUS NEAR ALL RESET FAR AUX 2 ALM SUSPEND EL-ZOOM MULTI SELECT FUNCTION PRE-POSI STILL L @1@2@3 HOME/- R ZOOM TELE WIDE AUX 1 @4@5@6 DOWN CAMERA SET SETUP UNIT CAM ON/OFF ESC
!0 Home/Decrement button (HOME/–) Moves the camera to the home position. During the setup, this button is used to select the desired parameter in the setup menu. !1 Auto Focus button (AUTO FOCUS) Activates the auto focus function when the specified camera with auto focus feature is selected. !2 Camera/Set button (CAM/SET) CAM: Selects a camera. Enter a camera number with the numeric buttons, then press the CAM/SET button. SET: Executes the currently highlighted setting in the setup menu.
@5 Preset Position button (PRE - POSI) In combination with the numeric buttons and CAM (SET) button, moves the camera to the desired preset position. @6 Still button (STILL) Freezes the picture on the multiscreen monitor. The indicator lights up when the still mode is selected. @7 Camera Set buttons (CAMERA SET ON/OFF) Open or close the camera setup menu on the monitor screen. ON: Opens the selected camera setup menu on the monitor, if applicable.
INSTALLATIONS (For WJ-FS616/FS616C) Warning! The installation should be made by qualified service personnel or system installers according to the following instructions. ■ System Connections ● Connection Example The connection example shows cameras and an alarm sensor connected to the Video Multiplexer. A time lapse VCR will record pictures for later playback.
● DATA Port Connection (For Multiplexer) Data ports are connected with RS-485 cables among devices using the Camera Communication protocol as follows. Note: When using cables other than those supplied, make sure to use shielded 4-wire twisted pair cable suitable for RS-485 communication. • Internal Diagram 1 6 No. Data Flow Name No.
● Unit Version ■ Controller Number Setting The unit ID is defined by the upper 3 bits depending on the software version installed in the unit. • WJ-FS616 Set this switch always to 1 when using the System Controller in a system including a Multiplexer WJFS616/FS616C. 1 2 3 4 5 6 7 78 901 23 ON 456 OFF 8 CONTROLLER No. MODE • WJ-FS616C ● Switch Setting Procedures OFF ON 1 2 3 4 5 MODE 6 7 1. Remove the DC plug from the rear of the controller. 8 2.
SETUP PROCEDURES (For WJ-FS616/FS616C) To display the setup menus for the WV-CU360C System Controller on the LED display, set the MODE switch and power up the controller as described below. ■ Prior to Setup ■ Buttons and Controls used for Setup Do the following before entering the setup mode. The following buttons and joystick operations are used for setup. 1. Confirm that all necessary connections and switch settings are complete. 2.
■ Controller Setup Set up the baud rate and parity check mode for the controller while observing the LED on the front panel.
4. Press the ESC button to go back to the previous menu. Note: The baud rate and parity check mode of both the WJ-FS616/FS616C and the controller must be the same, otherwise data communications will not function. To confirm the WJ-FS616/FS616C setup, open the COM PORT SETUP window to check the DATA port column parameters. Refer to Multiplexer Setup for operation.
OPERATING PROCEDURES (For WJ-FS616/FS616C System) Note: For common operations to the controller and the WJ-FS616/FS616C, please refer to the manual included with the WJ-FS616/FS616C. The following pages describe only operations different from the WJ-FS616/FS616C. ■ Camera Selection ■ Camera Control One of the cameras connected to the system unit is selected. Cameras and their peripherals are controlled from the WVCU360C as follows.
Note: Auxiliary control may be ignored while zooming, focusing or panning/tilting is in operation. ■ VTR (VCR) Control You can operate a VTR (VCR) connected to the Video Multiplexer from the controller using the buttons listed below with the ALT indicator lit. ■ Alarm Operation When the WV-CU360C receives an alarm signal from the WJ-FS616/FS616C, the alarm indicator blinks. The alarm indicator changes from blinking to steady light when the alarm is automatically reset.
■ Camera Setup The cameras connected to the WJ-FS616/FS616C are set up from the controller. 6. Press the VTR/CAM button to reset all functions to the defaults, or press the SEQUENCE button to reset a selected function. VTR CAM Note: Make sure that the multiplexer and the controller are set to identical communication parameters. ● General Setup 1. Select a camera pressing the numeric buttons, then press the CAM/SET button. 2. Press the CAMERA SET ON button.
For WJ-SX350 Matrix Switcher System 53
MAJOR OPERATING CONTROLS & THEIR FUNCTIONS ■ Front View (Template for WJ-SX350) q w e OPERATE LOGIN ALARM r MONITOR CAMERA t y BUSY PROHIBITED System Controller WV-CU 360C For Matrix Switcher CAMERA SITE CONTROL ALT PAUSE FUNCTION IRIS !7!8!9 CLOSE OPEN UP IRIS RESET ACK/RESET BACK @0@1@2 FWD SEQ AUX FOCUS NEAR ALL RESET -1 CAM DEC +1 CAM INC RECALL BACK FWD FAR AUTO FOCUS L @3@4@5 PAN R ZOOM TELE WIDE HISTORY @6@7@8 DOWN STATUS PRESET POSI MON CAM ESC SET C
u Joystick Controller (UP/DOWN/L/R) Used to operate the Pan/Tilt Head manually, or to move the cursor to the desired position on the SETUP MENU of the Matrix Switcher. UP: DOWN: L: R: Upward Downward Left Right i Iris buttons (IRIS CLOSE/OPEN) Close or open the lens iris of cameras equipped with the specified lens. When these buttons are pressed at the same time, the lens iris is reset to the factory setting.
@1 @2 Backward/Forward Sequence button (SEQ BACK/FWD) BACK: In combination with the numeric buttons, runs a Tour or Group sequence backward on the selected monitor. It is also used to continue a sequence backward, that was previously paused on that monitor by pressing the PAUSE button. FWD: In combination with the numeric buttons, runs a Tour or Group sequence forward on the selected monitor.
INSTALLATIONS (For WJ-SX350) CAUTION The installation should be made by qualified service personnel or system installers according to the following instructions. ■ System Connections ● Connection Example The example below shows a typical system connection.
● DATA Port Connection (For WJ-SX350) Data ports are connected with RS-485 cables among devices as follows. Note: When using cables other than those supplied, make sure to use shielded 4-wire twisted pair cable suitable for RS-485 communication. • Internal Diagram 1 6 No. Data Flow Name No.
■ Controller Number Setting For version 1.xx, set the switches as shown below. Set this switch always to 1 when using the System Controller with the WJ-SX350. OFF ON 456 78 1 23 901 2 3 4 5 6 7 8 MODE CONTROLLER No. • Bit 1 should be set to OFF*. • Bit 2 should be set to ON. • Bit 3 should be set to OFF*. ● Switch Setting Procedures Set the MODE DIP switch and CONTROLLER NO. switch as follows. 1. Remove the DC plug from the rear of the controller. 2. Set the MODE switches.
CONTROLLER SETUP PROCEDURES (For WJ-SX350) To display the setup menus for the WV-CU360C System Controller on the LED display, set the MODE switch and power up the controller as described below. ■ Prior to Setup ■ Buttons and Controls used for Setup Do the following before entering the setup mode. The following buttons and joystick operations are used for setup. 1. Confirm that all necessary connections and switch settings are complete. 2.
■ Setup Procedures Set up the baud rate and parity check mode for the controller while observing the LED on the front panel.
OPERATING PROCEDURES (For WJ-SX350) This section describes only some important operations such as login, logout, and different operations from the front panel of the WJ-SX350. Please refer to the manual included with the WJ-SX350 for further information on camera selection, monitor selection and so forth. ● Logout 1. Type 00 using the numeric button, then press the FUNCTION button. The LOGIN indicator turns off. FUNCTION ■ Login & Logout ● Login 1.
■ Pan/Tilt Control (Auto/Random Panning) 1. Select the desired monitor and camera. 2. Type 1 using the numeric button, then press the PAN button to toggle the Auto Panning function on the selected camera On and Off. 3. Type 2 using the numeric button, then press the PAN button to toggle the Random Panning function on the selected camera On and Off. 1 2 ● Defroster Control 1. Select the desired monitor and camera. 2.
● System Status Display 1. Select a monitor to display the System Status Table. 2. Press the ALT button (indicator light on), then press the STATUS button to toggle the display of the System Status Table on the selected monitor On and Off.
For System 850 WJ-SX850 Matrix Switcher System 65
MAJOR OPERATING CONTROLS & THEIR FUNCTIONS ■ Front View (Template for System 850 Matrix Switcher) q w e OPERATE LINK ALARM r t y MONITOR CAMERA u i BUSY PROHIBITED System Controller WV-CU 360C For Matrix Switcher (System 850) CAMERA SITE CONTROL ALARM ACK RESET IRIS !9@0@1 CLOSE ALL RESET DISARM GROUP PRESET PREV OPE ID S-CTL ID LOG OUT PAUSE NEXT CAM ID GEN AUX1 ON VLD S MDN STATUS WIPER SYS S ALL PROGRAM PRESET @2@3@4 OPEN FOCUS NEAR AUX1 OFF ALM S STOP CAM MENU OFF G
o Joystick Controller (UP/DOWN/L/R) Used to manually operate the Pan/Tilt Head, or move the cursor in the camera menu on the active monitor screen. UP: Upward DOWN: Downward L: Left R: Right !6 Clear/Escape button [CLEAR (ESC)] Clear: Clears numeric input from the LED display. Escape: Escapes from the currently highlighted selection and return to the previous page of the camera menu. !0 Iris buttons (IRIS, CLOSE/OPEN) Closes or opens the lens iris of cameras equipped with the specified lens.
@1 Alarm Reset button (RESET) Cancels an activated alarm. Press this button to reset an alarm activated in the currently active unit. Pressing this button while holding down the SHIFT button cancels all currently activated alarms at a time (ALL RESET). Pressing RESET in the camera menu will reset the parameter of a selected item or open the Special camera menu when the cursor is positioned on SPECIAL in the menu. Pressing it while holding down the SHIFT button will restore all factory default settings.
#2 Monitor/Monitor Lock/OSD service button (MONITOR/OSD SERVICE), Lock indicator (LOCK) Selects a monitor by entering a monitor number with the numeric buttons, and then pressing this button. To lock or unlock the currently selected monitor, press this button while holding down the SHIFT button. While the LOCK indicator is lit, other operators will be barred from accessing the monitor. To access OSD service, press the numeric buttons shown below, then press this button.
INSTALLATIONS (For System 850) CAUTION The installation should be made by qualified service personnel or system installers according to the following instructions. ■ System Connections ● Connection Example The connection example shows a large-scale system having a number of cameras, alarm sensors, monitors and so forth connected to the System 850 Matrix Switcher. The System Controller WV-CU360C provides major operating functions to control the system.
● DATA Port Connection Data ports are connected with RS-485 cables among devices using Camera Communication protocol as follows. Note: When using cables other than those supplied, make sure to use shielded 4-wire twisted pair cable suitable for RS-485 communication. • Internal Diagram 1 6 No. Data Flow Name No.
■ DIP Switch Setting An 8-bit DIP switch mounted on the rear panel specifies communication mode, etc. The default position is marked with an asterisk *. 78 23 901 456 CONTROLLER No.
SETUP PROCEDURES (For System 850) To display the setup menus for the WV-CU360C System Controller on the LED display, set the MODE switch and power up the controller as described below. ■ Prior to Setup ■ Buttons and Controls used for Setup Do the following before entering the setup mode. The following buttons and joystick operations are used for setup. 1. Confirm that all necessary connections and switch settings are complete. 2.
■ Setup Procedures Set up the baud rate and parity check mode for the controller while observing the LED on the front panel.
OPERATING PROCEDURES (For System 850) Note: This section describes only some important operations such as login, logout, and different operations from the front panel of the System 850. Please refer to the manual included with the System 850 for further information on camera selection, monitor selection and so forth. ■ Login & Logout ● Login 1. Turn on the power switches of all system components. 1 2. Turn on the power of the WV-CU360C System Controller by connecting the AC adapter to the AC outlet.
Appendix 77
SPECIFICATIONS Power Source: Data Output/Input Port: Switching Functions : Controller Number Unit Address Selection: Monitor Number Selection: Camera Number Selection: Lens Functions: Housing: Pan/Tilt: Other Camera Controls: System Operation: Ambient Operating Temperature: Ambient Operating Humidity: Dimensions: Weight: Input Power Source: Power Consumption: Output Power Source: Power Consumption: 9 V DC, 400 mA (Use the supplied AC Adapter only) 6-conductor modular jack (RS-
ALL RESET The System Controller WV-CU360C can be reset to the default settings. 1. Remove the DC plug of the AC adapter from the controller. 2. While pressing numeric buttons 2, 4 and 6 simultaneously, plug in the DC plug. 1 2 3 4 5 6 7 8 9 HOME PRESET 0 3. When all indicators light up, resetting is completed. ESC SET PROGRAM PRESET Note: Keep the DC plug connected to the controller until the reset procedure is completed.
Panasonic Security and Digital Imaging Company A Division of Matsushita Electric Corporation of America Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094 Regional Offices: Northeast: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303 Southern: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 (770) 338-6838 Midwest: 1707 North Randall Road, Elgin, IL 60123 (847) 468-5211 Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840 Panasonic Canada Inc.