Repeater Operating Instructions Model No. VL-FAN1BX Thank you for purchasing a Panasonic Repeater. This unit is an accessory unit for Panasonic Wireless Video Intercom System. You must register this unit to the main monitor station before using. Please read these Operating Instructions before using the unit and save for future reference. VL-FAN1BX_0329.
Table of Contents Important Information Important safety instructions .................................................................... 3 Additional safety information .................................................................... 4 For best performance ............................................................................... 5 LBefore using ................................................................................................................. 5 LLocation/avoiding noise ..........
Important Information Important safety instructions 1) Read these instructions. All the safety and operating instructions should be read before the appliance is operated. 2) Keep these instructions. The safety and operating instructions should be retained for future reference. 3) Heed all warnings. All warnings on the appliance and in the operating instructions should be adhered to. 4) Follow all instructions. All operating and use instructions should be followed. 5) Do not use this apparatus near water.
Important Information Additional safety information 1. Use only the power source marked on the unit. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. 2. Use only the specified AC adaptor. 3. Do not tamper with the plug. 4. Make sure the plug is securely inserted. 5. Do not touch the plug with wet hands. 6. Do not place objects on the power cord. Install the unit where no one can step or trip on the cord. 7.
Important Information For best performance Before using L� It is prohibited to disassemble or modify this unit. Contact the dealer where you purchased this unit for repairs. L� When power fails, this unit cannot be used. Location/avoiding noise L� This unit uses radio waves to communicate with the devices to be relayed.
Important Information Installation L� If there are no obstacles between this unit and the main monitor station, you can install the unit within about 100 m from the main monitor station. (Usage area varies depending on the location where the unit is installed. Install the unit in the locations where the STATUS indicator lights in green (page 14).) Lights in green.
Important Information Tapping This unit uses digital wireless technology so that a call is rarely intercepted. However, calls may be tapped by a third party because the unit also communicates using radio waves. L� “Tapping” means that the other party intercepts a radio message intentionally or accidentally by using a receiver.
Introduction Included items 1 2 3 4 5 6 No. Item Quantity Notes 1 Repeater 1 ------ 2 AC adaptor 1 Cord length: Approx. 3 m 3 AC cord 1 Cord length: Approx. 1.8 m 4 Wood screws 2 For wall-mounting 5 Washers 2 For wall-mounting 6 Registration number sticker 1 ------ 8 VL-FAN1BX_0329.
Introduction Feature highlights If the sub monitor station is away from the main monitor station or there are the following obstacles between them, the radio signal weakens. In this case, sound cuts in and out, and moreover “OUT OF RANGE” is displayed on the sub monitor station as it cannot be used. The repeater strengthens the radio wave signal and extends the range of use which may resolve these problems when it is installed between the main monitor station and the sub monitor station.
Preparation Location of controls N� Front View / Right side view A Antenna L� Transmitter/Receiver of radio waves. A B B {PROGRAM} button L� Press to register to the main monitor station. C Indicators L� Show the status of this unit and the radio signal level (page 11). C N� Rear view D DC IN jack L� Connect the AC adaptor. E {FACTORY DEFAULT RESET} button L� Press to reset the settings of this unit to their default settings (page 17). D Bottom view E 10 VL-FAN1BX_0329.
Preparation Indicators The indicators show the status of this unit and radio wave signals as follows. Indicator Status POWER STATUS Green, light on The power is turned on. Light off The power is turned off. Green, flashing While registering to the main monitor station. Light off This unit has not been registered to the main monitor station. Green, light on Strong Shows the radio signal status from the main monitor station.
Installation Registering the repeater to the main monitor station (REGISTRATION/CANCELLATION) To use the repeater, the registration to your main monitor station is required. L� The repeater can only be registered to one main monitor station at a time. Registering the repeater (REGISTRATION) 1 Connect the AC cord to the AC adaptor, then connect the AC cord to a power outlet installed nearby the main monitor station. L� The POWER indicator lights in green.
Installation 4 Attach the included registration number sticker on the repeater. Registration number sticker (Example: 1st. repeater) 5 Disconnect the AC adaptor and place the repeater in the desired location. L� Even if you disconnect the AC adaptor, the registration to the main monitor station is not canceled. To stop using the repeater (CANCELLATION) 1 Perform the cancellation operations using the main monitor station.
Installation Installing the repeater After completing the registration to the main monitor station, install the repeater. LRefer to “For best performance” on page 5. 1 Connect the AC cord to the AC adaptor, then connect the AC cord to the power outlet. L� The POWER indicator lights in green. DC IN jack To power outlet (100 – 240 V AC) AC adaptor Lights in green. DC plug AC cord 2 Confirm the STATUS indicator. L� The STATUS indicator shows the radio signal status.
Installation Wall-mounting You can mount the repeater on the wall with the included wood screws and washers. Mount the repeater on a wall (pillar) where the wood screws can be firmly fixed. 1 Drive the wood screws with washers into the wall (pillar). Approx. 60 mm the repeater down until it is secure. L� About 140 mm of space above the washers is required for raising the antenna. Wall mount template 2 Mount onto the wall, directing the wood screws into the slots on the repeater, and slide Approx.
Help Troubleshooting Indicator Problem Cause & Solution Page The POWER indicator is turned off. L� The power is not turned on. Connect the AC adaptor. 14 The STATUS indicator is turned off. L� The repeater has not been registered. Register it to the main monitor station. 12 The STATUS indicator is flashing in red. L� The power of the main monitor station is not turned on. Turn it on. L� The repeater is out of range. Install it in a location where the STATUS indicator lights in green.
Help Cleaning When cleaning this unit, disconnect the AC adaptor from the power outlet. Clean the repeater with a soft, dry cloth. Important: L� Do not use anything containing alcohol, polish powder, powder soap, benzine, thinner, wax, petroleum, or boiling water. Also do not spray with insecticide, glass cleaner, or hair spray. This could cause a change in color or quality.
General Information Technical data about this product Power supply: Current consumption: Dimensions: Mass (Weight): Operating environment: Frequency: AC adaptor (100 – 240 V AC, 50/60 Hz) (12.0 V DC, 750 mA) Standby: Approx. 0.05 A During operation: Approx. 0.08 A Approx. height 27 mm x width 101 mm x depth 82 mm Approx. height 69.5 mm x width 101 mm x depth 82 mm (when raising the antenna) Approx. 85 g 0 °C to 40 °C, Up to 90% RH (Relative Humidity) non condensing 2.402 GHz – 2.
Index A AC adaptor .......................... 8, 12, 14 AC cord ............................... 8, 12, 14 Antenna ......................................... 10 C Cancellation ................................... 13 Cleaning ........................................ 17 D DC IN jack ......................... 10, 12, 14 F {FACTORY DEFAULT RESET} button .................................. 10, 17 I Indicators ....................................... 10 IN USE indicator .......................
For your future reference Date of purchase Serial number (found on the bottom of the unit) Dealer’s name and address Dealer’s telephone number Attach your sales receipt here. Panasonic Communications Co., Ltd. 1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan Copyright: ● This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use only.