Operating Instructions (For Basic Operations) Electronic Board (elite Panaboard) Model No. UB-T780 UB-T780 Stand is sold separately. Installation Manual Included (for qualified service personnel) • To assemble this unit, please refer to the Installation Manual on pages 31 through 50. • Before operating this unit, please read these instructions completely and keep them carefully for future reference. • This unit is designed for installation by a qualified servicing dealer.
Introduction Introduction Thank you for purchasing the Panasonic Electronic Board. For optimum performance and safety, please read these instructions carefully. Feature Highlights By connecting the elite Panaboard to a computer and using a projector to display the contents of the computer’s screen on the elite Panaboard, you can do the following. Electronic Pen Features • Manipulate objects on the computer screen by using the electronic pen as a mouse.
Introduction Things you should keep a record of Attach your sales receipt here For your future reference Date of purchase Serial number Dealer’s name 1 Dealer’s address Dealer’s tel no. About the Operating Instructions There are 2 separate operating manuals for the elite Panaboard. For Basic Operations (this document) Instructions for connecting and operating the elite Panaboard, as well as instructions for installation construction.
Introduction Federal Communications Commission Requirements For United States Only Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Introduction System Requirements Computer CPU Operating System Interface Memory (RAM) Hard Disk IBM® PC/AT® or compatible with a CD-ROM drive Intel® Pentium® 4 processor or later Windows 2000 SP4 / Windows XP / Windows Vista USB 2.0 256 MB or greater (Windows 2000 SP4) 512 MB or greater (Windows XP) 512 MB or greater (Windows Vista) Hard disk with at least 200 MB of free space (not including the space required for saving files) Note • • • • • • • • To run the elite Panaboard software, Microsoft .
Introduction Exemption of Liability Panasonic Communications Co., Ltd. is not responsible for accidents or injuries caused by, but not limited to, the following: 1. Altering the device or improper installation construction. 2. Using the device for purposes beyond its intended use. 3. Earthquake, fire, flood, tidal wave, hurricane, lightning or other natural phenomena. 4. Natural aging of the building or similar phenomena. For FRG Users (For Germany Only) Note Machine noise information regulation - 3.
Table of Contents For Your Safety ........................................................................................8 For Your Safety .................................................................................................................8 For Users ...........................................................................................................................8 Safety Information (For United Kingdom Only) ............................................................11 Precautions ..
Safety Your For For Your Safety For Your Safety To prevent severe injury and loss of life, read this section carefully before using the unit to ensure proper and safe operation of your unit. The following graphic symbols are used in this Operating Instructions manual. WARNING Denotes a potential hazard that could result in serious injury or death. CAUTION Denotes hazards that could result in minor injury or damage to the unit.
For Your Safety Plug the power cord firmly into an AC outlet. Otherwise, it can cause fire or electric shock. Installation and Relocation Have the unit installed, removed and disposed of only by qualified service personnel. Do not pull, bend, rest objects on, or chafe the power cord and plug. Damage to the power cord or plug can cause fire or electric shock. Do not attempt to repair the power cord or plug.
For Your Safety Batteries that seem worn down or damaged should not be used. Using worn down or damaged batteries may result in leaking. Do not charge, short, heat, break or throw in a fire, as it may result in the battery leaking, generating heat, or bursting. When disposing of the battery, cover the battery contacts with insulation (ex. tape). Direct contact with other batteries may result in leaking, fire, or explosion.
For Your Safety Safety Information (For United Kingdom Only) Locking the casters (Push this side) Push to lock Move this unit with two persons. Otherwise, this unit may fall down and cause injury. Operating Safeguards If the unit is fallen down or damaged, turn the unit off and unplug the power cord. Otherwise, it may cause fire or electric shock. Do not lean against the screen or on the cover (lower), even if the unit is mounted on the wall.
For Your Safety How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse. Precautions About Using the Battery If a battery is used improperly, the battery may leak, causing corrosion of the unit, or it may burst. To prevent this, always follow the precaution given below. • If the electronic pen ceases to function because the battery has run out, remove it immediately and dispose of it according to local regulations.
Usage Usage Included Accessories Check that all of the following items are included with your elite Panaboard. In the event that an item is missing, please contact your dealer. List of Accessories Power Cord (3 m [9 ft. 10 3/8 in.]) 1 USB Cable (5 m [16 ft. 5 3/8in.
Usage Names and Uses of the Parts Screen Front View Position Sensor Detects the position of the electronic pen. Do not block the sensor while operating the elite Panaboard. Screen Board Project the contents of a computer screen using a projector. Power Switch Pen Tray Push the center of the door to open the pen tray, which can hold up to 2 electronic pens. Status LEDs Left: Power LED (green) Lights green when the power is on. Right: Error LED (red) Lights red when an error occurs.
Usage Notice • The elite Panaboard is designed exclusively for projector images. Do not write on the screen board with a white-board marker. If you write on the screen board with a white-board marker, you cannot erase it with a standard eraser. Use a commercially available melamine foam eraser to erase. Electronic Pen Penpoint When you push down on the penpoint, ultrasonic waves and infrared signals are transmitted, and equivalent of a left mouse click is performed.
Usage • When operating the electronic pen, you will hear a buzzing sound due to the pen emitting ultrasonic waves for location detection. This sound does not have any negative effects for nearby people or devices. It will not cause electrical shocks. Inserting (Replacing) Batteries 1. Remove (replace) the battery cover. • 16 When replacing the cover, follow the procedure in reverse. Operating Instructions (For Basic Operations) 2. Insert (exchange) the battery and replace the cover.
Usage Connecting External Components 1. Set the power switch to "O" (OFF), connect the power cord (included) to the elite Panaboard, and plug the power cord into an AC outlet. Rear Power Switch (ON) (OFF) 1 Power Cord (Included) Power Cord • • Plug the power cord into an outlet that is close to the elite Panaboard and in a location that is easy to unplug. If you are using the optional stand, plug the power cord into the AC inlet, and secure the cord as shown in the illustrations below.
Usage 2. Connect the elite Panaboard to a computer using the USB cable (included). • elite Panaboard: Plug the B connector (smaller connector) into the elite Panaboard's USB port. • Computer: Plug the A connector (larger connector) into a USB port on the computer. Do not connect the elite Panaboard via a USB hub. This could result in erroneous operation. To USB Port USB Cable (Included) Projector Computer AC Video Cable AC 3. Connect the computer to a projector.
Usage Installing the elite Panaboard software You need to install the elite Panaboard software on the computer that will be used with the elite Panaboard. To install the elite Panaboard software, follow the procedure below. Notice • • 6. When the following screen is displayed, confirm that the USB cable is not connected to your computer or the elite Panaboard, and click [OK]. • If the USB cable is connected to the elite Panaboard, disconnect the cable, and click [OK]. • If .NET Framework 1.
Usage Setting the Projector Set up your projector as instructed below. About Positioning the Image • When you are projecting an image, make sure that the edge of the projected image is at least 5 mm (1/4 in.) from the screen frame. The electronic pen may not function correctly within 50 mm (2 in.) of the position sensor in the upper-left corner of the screen board. 50 mm (2 in.) 5 mm (1/4 in.) Projectable Area 5 mm (1/4 in.) 20 Operating Instructions (For Basic Operations) 5 mm (1/4 in.
Usage • If the image is projected trapezoidally, the position of the electronic pen may not be read correctly. Adjust the projector so that the projected image is a rectangle. Refer to your projector's documentation for information on adjusting the projected image.
Usage Starting the elite Panaboard software and Performing Calibration 1. Turn on the elite Panaboard. 2. Connect the elite Panaboard to your computer with the USB cable. • The elite Panaboard software starts automatically. • When you start the elite Panaboard software for the first time, the calibration screen is displayed. • Restart your computer if you are prompted to do so. After the computer has restarted, connect the elite Panaboard to your computer with the USB cable. 3. Perform calibration. 4.
Usage • After calibration has completed, the icon is displayed in the notification area, and the Desktop Drawing Tool is automatically displayed. Uninstalling the elite Panaboard software If it is necessary to uninstall the elite Panaboard software, follow the procedure below. 1. Turn on your computer and start Windows. • Log into an account with Administrator privileges. 2. Select [Add or Remove Programs] from the Control Panel.
Usage Viewing the Electronic Documentation Follow the procedure below to view the electronic documentation "Operating Instructions (For Software)". 1. Turn on your computer and start Windows. 2. Open "Operating Instructions (For Software)" from the Start menu. ([Start] ® [All Programs] ® [Panasonic] ® [elite Panaboard] ® [Operating Instructions for Software]) • The electronic documentation will be displayed. • For Windows 2000, [Programs] is displayed instead of [All Programs].
Appendix Daily Care When cleaning the elite Panaboard or inside the elite Panaboard, make sure to switch off the power and unplug the power cord from the AC outlet. Cleaning the elite Panaboard Replacing the Battery in the Electronic Pen When the charge in the battery in the electronic pen is low, the message, "The pen battery is low. Replace the battery soon." will be displayed on the computer screen. Continued use of the electronic pen can lead to poor performance.
Appendix Replacing the Penpoint of the Electronic Pen As the penpoint of the electronic pen becomes worn, a hole will appear in the penpoint. Continuing to use the electronic pen in this condition can cause damage to the screen or unsatisfactory operation, so replace the penpoint with a new one as soon as possible.
Appendix Troubleshooting When experiencing problems, please refer to the table below for possible solutions. If the problem persists, contact your dealer. Symptom Possible cause and solution The LEDs do not light when Check that the power cord is properly plugged in. the power switch is turned → If the problem persists, turn off the power, and then turn it on on. again. Red LED is blinking. Turn off the power, and turn it on again. → If the problem persists, contact your dealer.
Appendix Symptom 28 Possible cause and solution See page The message "The pen battery is low. Replace the batReplace the electronic pen's battery with a new one. tery soon." is displayed on the computer screen. 16 25 Because the elite Panaboard is designed exclusively for projector Marks written with a white-board marker cannot images, you cannot erase the marks with a standard eraser. be erased. → Use a commercially available melamine foam eraser to erase.
Appendix Specifications Model Number General UB-T780 Power AC 100 V–240 V, 50 Hz/60 Hz Power Consumption: During Operation 0.1 A External Dimensions: Height × 1,340 mm × 1,752 mm × 89 mm Width × Depth (4 ft. 4 7/8 in. × 5 ft. 9 1/8 in. × 3 1/2 in.) Weight 26 kg (57.32 lbs) Operating Environment Temperature: 15 °C to 30 °C (59 °F to 86 °F) Humidity: 30 % to 80 % Storage Environment Temperature: -20 °C to 40 °C (-4 °F to 104 °F) Humidity: 15 % to 80 % Interface USB 2.
Appendix Optional Devices and Accessories Optional Device Stand KX-B061 Accessories Electronic Pen UE-608025 • 30 To purchase separately sold items, contact your dealer.
Installation Manual Installation Manual (for qualified service personnel) • • • Request assembly of the Electronic Board, stand and wall mounting from your dealer. Before assembly and construction, read this section thoroughly. When installing the elite Panaboard on a wall or on the stand, perform installation with 2 people. For Your Safety To prevent severe injury and loss of life, read this section carefully before using the unit to ensure proper and safe operation of your unit.
Installation Manual CAUTION After installing or moving the electronic board, lock the casters and set the fall-prevention extension legs. Locking the casters (Push this side) Push to lock If the unit is hung on a wall, confirm the wall must be capable of supporting at least the following weight. 1,324 N (135 kgf) Do not attach the electronic board to mortared walls. Accidental electric leakage from the wall mounting plate bolts to metal laths or wire laths can cause heat, smoke or a fire.
Installation Manual Included Accessories Confirm that the following items are included with the elite Panaboard. No. Part Name Illustration Q’ty Remarks Power Cord (3 m [9 ft. 10 3/8 in.]) 1 The illustration of the power cord is for the United States. The shape of the plug may vary depending on country/area. USB Cable (5 m [16 ft. 5 3/8 in.
Installation Manual Notice • 34 Screws (8 count) for wall mounting are not included. Please purchase screws with a size of M6, appropriate for your type of wall (page 37).
Installation Manual Wall Mounting Construction Checking the Wall When mounting on a wall, consult with your building's owner, caretaker or construction manager to determine if the wall strength is sufficient to install the elite Panaboard. For safety, install the elite Panaboard only after thoroughly understanding the type of walls, the appropriate types of screws and the construction method (Page 37). CAUTION Do not attach the electronic board to mortared walls.
Installation Manual Installing the Wall Mounting Plates 1. Ensure that the wall is strong enough to support the elite Panaboard. Rated strength: greater than 1,324 N (135 kgf) 2. Using the measuring tape and level, mark the 8 locations to insert the screws. 469.5 mm (1 ft. 6 1/2 in.) 813 mm (2 ft. 8 1/8 in.) 222.5 mm (8 3/4 in.) 40 mm (1 5/8 in.) 982 mm (3 ft. 2 3/4 in.) 725 mm (2 ft. 4 5/8 in.) 30 mm (1 1/8 in.) 44 mm (1 3/4 in.
Installation Manual • • Tighten the bolt so that it will not become loose. When drilling the holes and installing the wall mounting plates, follow the procedure in "Wall Types and Installation Procedures" (page 37). 5. Mount the elite Panaboard on the wall. See "Assembling the elite Panaboard" (For Wall Mounting ® page 44). Wall Types and Installation Procedures The method for attaching the wall mounting plates to the wall will vary depending on the wall's structure.
Installation Manual Plasterboard walls Split-wing toggles (not included) are needed. Split-wing toggle Wall mounting plate Plasterboard Bolt Arms Insert the bolt through the hole in the wall mounting plate and into the hole in the wall so that the arms of the split-wing toggle are horizontal. For the correct hole size, refer to the instructions for the particular split-wing toggles used.
Installation Manual Stand Assembly (Sold Separately) Included Parts Check that the following parts are included with the stand (KX-BP061). No. *1 Part Name Illustration Q'ty Stand Base 2 Support Beam 2 Cross Bar (A) 2 Cross Bar (B) 1 Screw (M6 ´ 45 mm [1 3/4 in.]) 10 Two-wing Bolt (M5 ´ 12 mm [1/2 in.]) 2 Support Bracket 2 Fall-prevention Extension Leg 4 Screw (M6 ´ 60 mm [2 3/8 in.
Installation Manual CAUTION Before assembly, be sure to lock the casters. Locking the casters (Push this side) Assembly Instructions 1. Assemble the fall-prevention extension legs.
Installation Manual 2. Assemble the stand. Assemble with the holes toward the front. 1 Locking caster side (rear) FRONT REAR Locking caster side (rear) Notice • • Do not over-tighten the screw ( ). (Doing so can warp the support beams.) Assemble the stand so that the locking casters are on the rear side.
Installation Manual 3. Pull the fall-prevention extension legs down. 1 2 Note • When folding back the fall-prevention extension legs, release the lock as follows ( 1 , 2 ). 1 1 2 4. Mount the elite Panaboard. See "Assembling the elite Panaboard" (For Mounting on a Stand (Sold Separately) ® page 47).
Installation Manual Assembly Instructions Preparing for Removing the elite Panaboard from Its Packaging Open the box, remove the accessory box & packing foam and open the plastic sheet of the elite Panaboard. Shipping Box 1 [Accessory Box Contents] • • • • • Electronic Board • • • • • • Power Cord . . . . . . . . . . . . . . 1 USB Cable . . . . . . . . . . . . . . . 1 CD-ROM . . . . . . . . . . . . . . . . 1 Cable Holder . . . . . . . . . . . . 1 Wall Mounting Plate (Right, Left) . . . . . . .
Installation Manual Assembling the elite Panaboard For Wall Mounting 1. Loosely wrap the power cord with the cable tie, and plug the power cord into the AC inlet. • Connect the power cord to the elite Panaboard before installing on a wall. 3. Pull the loose end of the cable tie to tighten it, and install the power cord depending on the location of the outlet, as illustrated in the following diagrams. • When attaching the power cord downward. Fasten the power cord with the cable tie.
Installation Manual 4. Hang the elite Panaboard on the wall mounting plates with the screw heads. 6. Remove the 4 latches from the board attachment by pushing them towards the rear. 1 Latches 5. Remove the lower frame cover. Remove the left and right screws, and then remove the lower frame cover from the main unit of the elite Panaboard. Board Attachment 7. Fasten to the wall. Using the remaining 4 screws, securely fasten the lower portion of the board attachment to the wall. Lower Frame Cover 8.
Installation Manual How to Attach the Lower Frame Cover a. Holding the lower frame cover with both hands, slide it into the guides on both sides. c. Pull the lower frame cover ( 1 ). While keeping the rear section of the lower frame cover against the rear of the board, push the lower frame cover up into the rear of the board ( 2 ). B A b. Push the lower frame cover backward ( 1 ). While keeping the lower frame cover's rib against the rear side of the guides, push the lower frame cover upwards ( 2 ). d.
Installation Manual 9. Wipe the screen board surface. Gently wipe the screen board surface with a soft, moist cloth. For Mounting on a Stand (Sold Separately) 1. Attach the power cord. • Connect the power cord to the elite Panaboard before installing on the stand. Power Cord 1 Notice • • Do not use thinner, benzene, or abrasive chemicals to clean. (Doing so can result in discoloration.) Do not wipe the screen board with a dry cloth. (Doing so can cause static electricity build-up.) 2.
Installation Manual 3. Hang the elite Panaboard on the stand with the screw heads. • When installing the elite Panaboard on the stand, you can adjust its height to 4 different levels. When changing the height, remove the left and right screws from the back of the elite Panaboard, and securely insert them at the desired height. Torque (greater than 1 N·m [10 kgf·cm (9 lbf·in.)]). elite Panaboard Height Screw Position -100 mm (-4 in.) Highest Standard 2nd from top +100 mm (+4 in.
Installation Manual Confirming the elite Panaboard Operation After assembling the elite Panaboard, confirm that it operates properly by following the procedure below. Checkpoints Action Operation 1 Turn on the power. Measure Green LED lights. (Normal operation) Green LED does not light, or red LED is blinking. Check the power cord. See "Assembling the elite Panaboard" (For Wall Mounting ® page 44, For Mounting on a Stand (Sold Separately) ® page 47) step 1. Confirming the Interactive Features 1.
Installation Manual Repackaging To repackage the elite Panaboard, perform steps in "Assembling the elite Panaboard" (For Wall Mounting ® page 44, For Mounting on a Stand (Sold Separately) ® page 47) in reverse. Package the unit as depicted in the diagram in "Preparing for Removing the elite Panaboard from Its Packaging" (page 43). Notice • When handling the screen board, hold it by the frame and not the screen board itself. (Holding the screen board can result in the damage.
Notes 1 Operating Instructions (For Basic Operations) 51
Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.