Model No. TH-60PF30U TH-65PF30U Operating Instructions High De nition Plasma Display English Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. No user-serviceable parts inside. Refer servicing to quali ed service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons.
Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampli ers) that produce heat.
Dear Panasonic Customer Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new Plasma Display. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt as well, and record the model number and serial number of your set in the space provided on the rear cover of these instructions. Visit our Panasonic Web Site http://panasonic.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety Precautions CAUTION This Plasma Display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury. (All of the following accessories are manufactured by Panasonic Corporation.) • Speakers .................................................... TY-SP58P10WK (for TH-60PF30U), TY-SP65P11WK (for TH-65PF30U) • Pedestal .....................................................
Safety Precautions WARNING Setup Do not place the Plasma Display on sloped or unstable surfaces, and ensure that the Plasma Display does not hang over the edge of the base. • The Plasma Display may fall off or tip over. Do not place any objects on top of the Plasma Display. • If water spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result in re or electric shock.
Safety Precautions 3D Safety Precautions WARNING Small Parts 3D Eyewear contains small parts (battery and specialised band, etc.) and must be kept out of reach of small children to avoid accidental ingestion. Disassembly Do not disassemble or modify the 3D Eyewear. Lithium Battery Batteries must not be exposed to excessive heat such as sunshine, re or the like. CAUTION To enjoy 3D images safely and comfortably, please read these instructions fully.
Safety Precautions Viewing 3D Content Content for 3D viewing includes commercially available Blu-ray discs, 3D broadcasts, etc. When preparing your own 3D content, ensure that it is properly produced. Do not use the 3D Eyewear if you have a history of over-sensitivity to light, heart problems, or have any other existing medical conditions. Please stop using the 3D Eyewear immediately, if you feel tired, are not feeling well or experience any other uncomfortable sensation.
Accessories Accessories Supplied Check that you have the Accessories and items shown Operating Instruction book CD-ROM (Operating instructions) Clamper × 1 TMME289 AC cord Remote Control Transmitter N2QAYB000535 Batteries for the Remote Control Transmitter (AA Size × 2) Ferrite core × 2 J0KG00000014 Use the Ferrite cores to comply with the EMC standard. (see page 61) Remote Control Batteries Requires two AA batteries. 1. Pull and hold the hook, then open the battery cover. 2.
Connections Speaker connection When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation. Speakers (Optional accessories) 2 1 Red Red Black Black While pressing the lever, insert the core wire. Return the lever. AC cord connection and xing, cable xing AC cord xing Unplug the AC cord Plug the AC cord into the display unit. Plug the AC cord until it clicks.
Connections Video equipment connection Ex. TH-65PF30U 3D IR TRANSMITTER: Connect the 3D IR TRANSMITTER (optional accessory). SERIAL: Control the Plasma Display by connecting to PC. (see page 15) SLOT: Terminal board (optional accessories) insert slot (see page 6) Note: The right side slot is for terminal board with 2-slot width. The terminal board with 1-slot width does not function when installed in the right side slot. Terminals are on the bottom side of the Plasma Display.
Connections HDMI connection [Pin assignments and signal names] Pin No. 1 2 3 4 5 6 7 8 9 10 Signal Name Pin No. 11 T.M.D.S Data2+ T.M.D.S Data2 Shield T.M.D.S Data2T.M.D.S Data1+ T.M.D.S Data1 Shield T.M.D.S Data1T.M.D.S Data0+ T.M.D.S Data0 Shield T.M.D.S Data0T.M.D.S Clock+ Signal Name T.M.D.S Clock Shield 12 T.M.D.S Clock- 13 CEC 14 Reserved (N.C.
Connections PC Input Terminals connection (Female) Shared with DVI-D IN. COMPUTER Audio Stereo mini plug (M3) Connect a cable which matches the audio output terminal on the computer. Conversion adapter (if necessary) Mini D-sub 15p RGB PC cable (Male) Notes: • With regard to the typical PC input signals that are described in the applicable input signals list (see page 68), adjustment values such as for the standard picture positions and sizes have already been stored in this unit.
Connections SERIAL Terminals connection The SERIAL terminal is used when the Plasma Display is controlled by a computer. Note: To use serial control for this unit, make sure to set the “CONTROL I/F SELECT” in the “NETWORK SETUP” menu to “RS-232C”. (see page 53) (Male) COMPUTER 9 5 8 4 7 3 6 2 1 RS-232C Straight cable Pin layout for SERIAL Terminal (Female) D-sub 9p Notes: • Use the RS-232C straight cable to connect the computer to the Plasma Display.
Power ON / OFF Connecting the AC cord plug to the Plasma Display. Connecting the plug to the Wall Outlet. Note: When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet rst. INPUT Press the Power switch on the Plasma Display to turn the set on: Power-On. MENU -/ VOL +/ ENTER/ Power Indicator Power Indicator: Green Remote Control Sensor Press the button on the remote control to turn the Plasma Display off.
Power ON / OFF When rst switching on the unit Following screen will be displayed when the unit is turned on for the rst time. Select the items with the remote control. Unit buttons are invalid.
Selecting the input signal Press to select the input signal to be played back from the equipment which has been connected to the Plasma Display. Input signals will change as follows: PC VIDEO COMPONENT* HDMI DVI VIDEO: Video input terminal in AV IN (VIDEO). COMPONENT*: Component or RGB input terminal in COMPONENT/RGB IN. HDMI: HDMI input terminal in AV IN (HDMI). DVI: DVI input terminal in DVI-D IN. PC: PC input terminal in PC IN.
Basic Controls Main Unit * The illustration is TH-65PF30U. Remote control sensor Volume Adjustment Volume Up “+” Down “–” When the menu screen is displayed: “+” : press to move the cursor up “–” : press to move the cursor down (see page 25) INPUT MENU -/ Main Power On / Off Switch Power Indicator The Power Indicator will light. • Power-OFF .... Indicator not illuminated (The unit will still consume some power as long as the power cord is still inserted into the wall outlet.) • Standby ........
Basic Controls Remote Control Transmitter ACTION button Press to make selections. ASPECT button Press to adjust the aspect. (see page 21) Standby (ON / OFF) button The Plasma Display must rst be plugged into the wall outlet and turned on at the power switch (see page 16). Press this button to turn the Plasma Display On, from Standby mode. Press it again to turn the Plasma Display Off to Standby mode. POS.
ASPECT Controls The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format picture. Note: Be aware that if you put the display in a public place for commercial purposes or a public showing and then use the aspect mode select function to shrink or expand the picture, you may be violating the copyright under copyright law.
Digital Zoom This displays an enlargement of the designated part of the displayed image. 1 Display the operation guide. EXIT Press to access Digital Zoom. The operation guide will be displayed. 1 During Digital Zoom, only the following buttons can be operated. [Remote control] OFF TIMER button [Unit] INPUT MENU -/ VOL +/ ENTER/ VOL button MUTE button VOL button POSITION / ACTION button 2 Select the area of the image to be enlarged. Press on the enlargement location to select.
Viewing 3D images You can enjoy viewing 3D images with contents or programmes compatible with 3D effect by using the 3D eyewear (optional). Note: You need the 3D IR TRANSMITTER (optional) and the 3D eyewear (optional) to view the 3D images on this display. For further information, see the instruction manuals of the 3D IR TRANSMITTER and the 3D eyewear. This display supports “Frame Sequential*1”, “SIDE BY SIDE*2”, “TOP AND BOTTOM*3” and “SIMULTANEOUS*4” 3D formats.
Viewing 3D images Troubleshooting for 3D Eyewear Symptoms Checks Cannot see 3D images There is something wrong with the 3D images • Has the 3D Eyewear been switched On? • Ensure that “3D EYEWEAR” in “3D SETTINGS” is set to “ON”. (see page 36) • Some 3D image signals may not be automatically recognized as 3D images. Set “3D INPUT FORMAT” in “3D SETTINGS” to match the picture format. (see page 36) • Check that there are no obstacles between the 3D IR TRANSMITTER and the 3D Eyewear.
On-Screen Menu Displays Remote Control 1 Display the menu screen. Unit Press several times. MENU Press to select. (Example: PICTURE menu) 2 Select the item. Each time the MENU button is pressed, the menu screen will switch. Normal Viewing PICTURE SET UP SOUND POS./SIZE Select. PICTURE Select. NORMALIZE NORMAL STANDARD 25 0 0 0 5 NORMAL PICTURE MENU PICTURE BRIGHTNESS COLOR TINT SHARPNESS COLOR TEMP ADVANCED SETTINGS Press. (Example: PICTURE menu) MEMORY SAVE MEMORY LOAD MEMORY EDIT Set.
Adjusting POS./SIZE 1 2 Press to display the POS./SIZE menu. Press to select the menu to adjust. POS./SIZE NORMALIZE NORMAL AUTO SETUP 3 4 H-POS H-SIZE V-POS V-SIZE DOT CLOCK CLOCK PHASE CLAMP POSITION 1:1 PIXEL MODE Press to adjust the menu. Press to exit from adjust mode. 0 0 0 0 0 0 0 OFF Note: Unadjustable items are grayed out. Adjustable items differ depending on the input signal and the display mode. Notes: • Adjustment details are memorized separately for different input signal formats.
Adjusting POS./SIZE Notes: • If the dot clock frequency of an analog signal is 162 MHz or higher, “DOT CLOCK” and “CLOCK PHASE” cannot be automatically corrected. • When digital signal input, DOT CLOCK and CLOCK PHASE cannot be made. • AUTO SETUP may not work when a cropped or dark image is input. In such case, switch to a bright image with borders and other objects are clearly shown, and then try auto setup again. • Depending on the signal, out of alignment may occur after AUTO SETUP.
Adjusting POS./SIZE CLAMP POSITION (During Component/PC input signal) Adjusts the clamp position when black parts of the image have no detail due to underexposure or are tinged with green. Optimum value for Clamp Position adjustment When black parts have no detail due to underexposure (blackout) Value that causes least blackout is the optimum. When black parts are tinged with green Value that cancels the greenishness without causing blackout is the optimum.
PICTURE Adjustments 1 2 Press to display the PICTURE menu. Select to adjust each item. Press to select the menu to adjust. Select the desired level by looking at the picture behind the menu. Note: Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input and menu setting.
PICTURE Adjustments Item PICTURE BRIGHTNESS COLOR TINT SHARPNESS Effect Less Adjustments More Darker Brighter Less More Reddish Greenish Less More Adjusts the proper picture contrast. Adjusts for easier viewing of dark pictures such as night scenes and black hair. Adjusts color saturation. Adjusts for natural esh tones. Notes: • You can change the level of each function (PICTURE, BRIGHTNESS, COLOR, TINT, SHARPNESS) for each PICTURE MENU.
Picture Pro les Up to 8 combinations of picture adjustment values (in the PICTURE menu and ADVANCED SETTINGS) can be stored in the display memory as pro les and applied as needed, for a convenient way to enjoy your preferred picture settings.
Picture Pro les Saving pro les Follow these steps to save picture adjustment values as pro les. Note: When the settings are locked in “EXTENDED LIFE SETTINGS”, pro les cannot be saved. 1 Specify the picture quality in the PICTURE menu and ADVANCED SETTINGS. (see page 29, 30) 2 In the PICTURE menu, select “MEMORY SAVE”. MEMORY SAVE 1 select MEMORY LOAD MEMORY EDIT 3 5 2 access A N a n 0 ! _ Select a pro le name for saving the picture adjustment values. 1 select MEMORY SAVE 1. [ 2. [ 3. [ 4.
Picture Pro les Loading pro les Load pro les and apply the picture adjustment values to the display as follows. Notes: • Loaded pro les are stored in memory according to the selected input interface. (see page 18) • When the settings are locked in “EXTENDED LIFE SETTINGS”, pro les cannot be loaded. Select the pro le to load. In the PICTURE menu, select “MEMORY LOAD”. select 1 MEMORY SAVE 1 2 MEMORY LOAD MEMORY LOAD MEMORY EDIT 2 access 1. [ 2. [ 3. [ 4.
SOUND Adjustment 1 SOUND Press to display the SOUND menu. 1/2 NORMALIZE NORMAL 2 Select to adjust each item. Press to select the menu to adjust. Select the desired level by listening to the sound. 3 AUDIO MENU BASS MID TREBLE BALANCE SURROUND STANDARD 0 0 0 0 OFF Press to exit from adjust mode. Item AUDIO MENU BASS MID TREBLE BALANCE SURROUND Details STANDARD: Emits the original sound. DYNAMIC: Accentuates sharp sound. CLEAR: Attenuates human voice. Adjusts low pitch sounds.
PRESENT TIME SETUP / SET UP TIMER The timer can switch the Plasma Display ON or OFF. Before attempting Timer Set, con rm the PRESENT TIME OF DAY and adjust if necessary. Then set POWER ON TIME / POWER OFF TIME. 1 2 Press to display the SET UP menu. Press to select SET UP TIMER or PRESENT TIME SETUP. Press to display the SET UP TIMER screen or PRESENT TIME SETUP screen.
3D SETTINGS To view the 3D images, please adjust and setup the 3D settings. Note: Set these settings for each input terminals.
SCREENSAVER (For preventing image retention) Do not display a still picture, especially in 4:3 mode, for any length of time. If the display must remain on, a SCREENSAVER should be used. 1 Press to display the SET UP menu. Press to select the SCREENSAVER. 2 Press to select the SCREENSAVER screen.
SCREENSAVER (For preventing image retention) Setup of SCREENSAVER Time After selecting TIME OF DAY, INTERVAL or STANDBY AFTER SCR SAVER, the relevant Time Setup will become available for selection and the Operating Time may be set. (Time cannot be set when “MODE” is “ON” or “OFF”.) Press to select START TIME / FINISH TIME (when TIME OF DAY is selected). Press to select SHOW DURATION / SAVER DURATION (when INTERVAL is selected).
Reduces screen image retention EXTENDED LIFE SETTINGS The following settings are setup to reduce image retention: SET UP 1/2 3D SETTINGS SIGNAL SCREENSAVER EXTENDED LIFE SETTINGS INPUT LABEL COMPONENT/RGB-IN SELECT RGB POWER SAVE OFF STANDBY SAVE ON PC POWER MANAGEMENT ON DVI-D POWER MANAGEMENT OFF ENABLE NO SIGNAL POWER OFF DISABLE NO ACTIVITY POWER OFF OSD LANGUAGE ENGLISH (US) EXTENDED LIFE SETTINGS Set to the recommended value Set individually Reset to the factory settings EXPRESS SETTINGS CUSTOM S
Reduces screen image retention NANODRIFT SAVER Moves the display position of the screen slightly to reduce image retention on the display panel. LOW–HIGH: NANODRIFT SAVER operates. The display position of the screen moves at set time intervals. You can set the screen movement range. Some of the screen may appear to be missing as a result of this operation. If you change the value, a mask is displayed in the range where the picture is missing as a result of position movement.
Reduces screen image retention CUSTOM SETTINGS Set the individual “Image Retention Reduction” menu. 1 Select “CUSTOM SETTINGS”. EXTENDED LIFE SETTINGS EXPRESS SETTINGS CUSTOM SETTINGS RESET 1 select 2 access set each menu to the recommended setting: 2 To Select “RECOMMENDED SETTINGS”.
Reduces power consumption • POWER SAVE: • STANDBY SAVE: • PC POWER MANAGEMENT: • DVI-D POWER MANAGEMENT: • NO SIGNAL POWER OFF: • NO ACTIVITY POWER OFF: When this function is turned ON, luminous level of the Plasma Display is suppressed, so power consumption is reduced. When this function is turned ON, power consumption of the microcomputer is reduced during power supply standby (see page 16, 19, 20), so standby power of the set is reduced.
Customizing the Input labels This function can change the label of the Input signal to be displayed. (see page 18) 1 SET UP Press to display the SETUP menu. 3D SETTINGS SIGNAL SCREEN SAVER EXTENDED LIFE SETTINGS INPUT LABEL COMPONENT/RGB-IN SELECT RGB POWER SAVE OFF STANDBY SAVE ON PC POWER MANAGEMENT ON DVI-D POWER MANAGEMENT OFF ENABLE NO SIGNAL POWER OFF DISABLE NO ACTIVITY POWER OFF OSD LANGUAGE ENGLISH (US) Press to select INPUT LABEL. 2 Press to display the INPUT LABEL screen.
Selecting the On-Screen Menu Language 1 2 Press to display the SET UP menu. Press to select OSD LANGUAGE. Press to select your preferred language. Selectable languages SET UP English(UK) Deutsch Français Italiano Español ENGLISH(US) .......(Chinese) .......(Japanese) .......
SET UP for MULTI DISPLAY By lining up Plasma Displays in groups, for example, as illustrated below, an enlarged picture may be displayed across all screens. For this mode of operation, each plasma display has to be set up with a Display number to determine its location. Note: During Multi display, the 3D images are displayed as 2D images. (Example) group of 4 (2 × 2) group of 9 (3 × 3) group of 16 (4 × 4) group of 25 (5 × 5) How to setup MULTI DISPLAY 1 SET UP Press to display the SET UP menu.
SET UP for MULTI DISPLAY Item Details Select “OFF” or “ON”. The brightness depends on each display’s setting. Equalize the brightness of all the displays. OFF ON AI-SYNCRONIZATION Notes: • If you set AI-SYNCRONIZATION to ON, the following menus will be unavailable and these settings will be xed to the initial values. PICTURE menu: COLOR, TINT, INPUT LEVEL (ADVANCED SETTINGS) • This function cannot be adjusted during input from VIDEO terminal. 4 Press to exit from adjust mode.
SET UP for PORTRAIT Divide an input image into 3 parts, and display one of them to a plasma display which is set vertically. The image will be enlarged 3 times and rotated 90-degree. (Example) Notes: • When using the PORTRAIT function with displays set vertically, “DISPLAY ORIENTATION” in SET UP menu has to be set to “PORTRAIT” (see page 44). • Turn up the power switch for the upward direction when you set Display vertically. • During Portrait display, the 3D images are displayed as 2D images.
SET UP for PORTRAIT 5 VIEWING AREA / LOCATION VIEWING AREA: Set a mode of image division for PORTRAIT function. LOCATION: Set a location of image to be displayed for PORTRAIT function. Press to select VIEWING AREA or LOCATION. PORTRAIT SETUP Press to select each function. PORTRAIT SETUP SEAM HIDES VIDEO VIEWING AREA LOCATION AI-SYNCHRONIZATION Notes: • For HD signal videos, the “VIEWING AREA” is set at “16:9”, and cannot be changed.
SET UP for Input Signals COMPONENT / RGB IN SELECT Select to match the signals from the source connected to the Component / RGB or PC input terminals. “COMPONENT” Y, PB, PR signals “RGB” RGB signals 1 2 SET UP Press to select the “COMPONENT / RGB-IN SELECT”. Press to select the desired mode. RGB COMPONENT 3 1/2 Press to display the SET UP menu. Press to exit from adjust mode.
SET UP for Input Signals SIGNAL menu SET UP Note: “SIGNAL” setup menu displays a different setting condition for each input signal. 1 3D SETTINGS SIGNAL SCREENSAVER EXTENDED LIFE SETTINGS INPUT LABEL COMPONENT/RGB-IN SELECT RGB POWER SAVE OFF STANDBY SAVE ON PC POWER MANAGEMENT ON DVI-D POWER MANAGEMENT OFF ENABLE NO SIGNAL POWER OFF DISABLE NO ACTIVITY POWER OFF OSD LANGUAGE ENGLISH (US) Press to display the SET UP menu. Press to select the “SIGNAL”. 2 Press to display the SIGNAL menu.
SET UP for Input Signals • SYNC This function operates only during input from PC IN terminal. Setting RGB sync signal Con rm that the input is set to RGB input (this setting is valid only for RGB input signal). AUTO: The H and V sync or synchronized signal is automatically selected. If both input, it is selected the H and V sync. ON G: Uses a synchronized signal on the Video G signal, which is input from the G connector.
SET UP for Input Signals • NOISE REDUCTION Sets the following three NR (Noise Reduction) functions together. VIDEO NR, MOSQUITO NR, BLOCK NR Press to select “NOISE REDUCTION”. ( ) NOISE REDUCTION OFF ( ) NOISE REDUCTION ADVANCED Press to select “OFF”, “MIN”, “MID”, “MAX”, “ADVANCED”. Advanced NR Sets the three NR functions separately. 1 Press to select “ADVANCED”. ADVANCED NR Press to enter ADVANCED NR. 2 Press to select VIDEO NR, MOSQUITO NR or BLOCK NR.
Network Setup Make the various settings to use the network function. SETUP 2/2 MULTI DISPLAY SETUP PORTRAIT SETUP SET UP TIMER PRESENT TIME SETUP NETWORK SETUP DISPLAY ORIENTATION LANDSCAPE DHCP, IP ADDRESS, SUBNET MASK, and GATEWAY settings 1 Set DHCP. When “OFF” is selected, IP ADDRESS and other settings can be set manually. 2 Select the item and press 3 Enter an address. IP ADDRESS 192.168. I 0.
Options Adjustments Options 1 Press to display the SET UP menu. Weekly Command Timer Audio input select Touch Panel settings Press to select “OSD LANGUAGE”. 2 Onscreen display Initial input Initial VOL level Maximum VOL level Input lock Button lock Remocon User level Press for more than 3 seconds. Press to select “Options”. 3 Options Shipping Press to display the Options menu. Press to select your preferred menu. 4 Press to adjust the menu.
Options Adjustments Item Adjustments Input lock Locks the input switch operation. PC SLOT INPUT*1 VIDEO COMPONENT*2 HDMI DVI Off *1 “SLOT INPUT” is displayed when an optional Terminal Board is installed. When a Terminal Board with dual input terminals is installed, “SLOT INPUT A” and “SLOT INPUT B” are displayed. *2 “COMPONENT” may be displayed as “RGB” depending on the setting of “COMPONENT/RGB-IN SELECT”. (see page 49) Notes: • Only the adjusted signal is displayed (see page 18).
Options Adjustments Item Adjustments Studio W/B Off: Nullify all the settings adjusted. On: Sets the color temperature for TV studio. Note: Valid only when the “WARM” is set as “COLOR TEMP” in PICTURE menu. Studio Gain Sharpens the contrast for a better view when a part of the image is too light to see. Off: Disables “Studio Gain”. On: Enables “Studio Gain”.
Options Adjustments Item Adjustments 3D Safety Precautions show/hide is set during power ON. On: 3D Safety Precaution is shown every time when the power is ON. Off: 3D Safety Precaution is not shown when the power is ON. When the setting changes from “On” to “Off”, the con rmation screen is displayed as below. Pressing “YES” switches the setting. 3D Safety Precautions 3D Safety Precautions If Off is selected, the 3D safety precautions will not be displayed when power is turned on.
Options Adjustments Press to select a command number. 5 Press to show the previous / next command pages (1-8) of the selected program. Press to show the command setting screen.
Options Adjustments Audio input select Set up the sound when an image input is selected. Options 1/3 Weekly Command Timer Audio input select Touch Panel settings Onscreen display On Press ACTION ( ) button Audio input select Press to select image input. Press to select audio input.
Options Adjustments Touch Panel settings (Settings when using Touch Panel) The mode to restrict NANODRIFT SAVER (see page 40) operation when using Touch Panel (available as an option) is set up. Options 1/3 Weekly Command Timer Audio input select Touch Panel settings Press ACTION ( ) button Touch Panel settings Touch Panel mode Calibration mode On Set “Touch Panel mode” to “On”. 1 select NANODRIFT SAVER in Touch Panel mode: On 2 adjust The value set for NANODRIFT turns into “ON” and displayed in gray.
Using Network Function This unit has a network function to control the network connected display with your computer. Note: To use the network function, set each “NETWORK SETUP” setting and make sure to set the “CONTROL I/F SELECT” to “LAN”. (see page 53) When “LAN” is set, the slot power is turned on, and power indicator is lit orange under the condition of power off with remote control (stand-by state), regardless of the “Slot power” setting.
Using Network Function PJLink™ Protocol The network function of the unit conforms with PJLink™ class 1 and you can operate the following actions from your computer using PJLink™ protocol. • Display setup • Display status query Supported commands Commands to control the unit with PJLink™ protocol are shown in the table below.
Using Web Browser Control You can use a Web browser to control the unit and set up a network and password. Before Using Web Browser Control To use the Web browser control, the unit and computer setups are required. Unit Setup Set each “NETWORK SETUP” setting and make sure to set the “CONTROL I/F SELECT” to “LAN”. (see page 53) Computer Setup Disable the proxy server settings and enable JavaScript. (Windows) Disable proxy server settings 1 Display [Internet Properties] window.
Using Web Browser Control TOP screen structure of the Web browser control After logging in, the TOP screen of the Web browser control is displayed. Menu Menu items are displayed. When a button is clicked, setup screen of each item is displayed. Item BASIC CONTROL OPTION CONTROL NETWORK SETTING CHANGE PASSWORD Details BASIC CONTROL screen is displayed. (see below) OPTION CONTROL screen is displayed. (see below) Network Setup screen is displayed. (see page 65) Password setup screen is displayed.
Using Web Browser Control NETWORK SETTING (Network Setup Screen) Click NETWORK SETTING from the menu. Various settings of a network can be set. For the details of the setting items, please check NETWORK SETUP under the SET UP of the unit. (see page 53) Item Notes: • To use a DHCP server, make sure the DHCP server is started. • During a DHCP server is used, IP ADDRESS, SUBNET MASK, and GATEWAY values cannot be entered. • When the set values are changed properly, “NETWORK SETTING CHANGED.
Troubleshooting Before you call for service, determine the symptoms and make a few simple checks as shown below. Symptoms Picture Checks Sound Interference Noisy Sound Electrical Appliances Cars / Motorcycles Fluorescent light Normal Picture No Sound Volume (Check whether the mute function has been activated on the remote control.
List of Aspect Modes Aspect mode All Aspect: Factory setting On All Aspect: Off 16:9 14:9 FULL JUST JUST Pictures with a 4:3 aspect ratio are enlarged horizontally so that the picture distortion is minimized. The left and right edges of the pictures are cut off. The display of the areas around the left and right edges of the screen is slightly elongated. 4:3 4:3 (1) 4:3 H-FILL Zoom ZOOM Zoom1 Zoom2 Zoom3 The display of the pictures lls the screen.
Applicable Input Signals 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 Signal name Horizontal frequency (kHz) Vertical frequency (Hz) 525 (480) / 60i 525 (480) / 60p 625 (575) / 50i 625 (576) / 50i 625 (575) / 50p 625 (576) / 50p 750 (720) / 60p 750 (720) / 50p 1,125 (1,080) / 60p 1,125 (1,080) / 60i 1,125 (1,080) / 50p 1,125 (1,080) / 50i 1,125 (1,080) / 24sF 1,125 (1,080) / 30p 1,125 (1,080) / 2
Applicable Input Signals Video input (VIDEO) Signal name 1 2 3 4 5 NTSC PAL PAL60 SECAM Modi ed NTSC Horizontal frequency(kHz) 15.73 15.63 15.73 15.63 15.73 Vertical frequency(Hz) 59.94 50.00 59.94 50.00 59.94 Shipping condition This function allows you to reset the unit to the factory setting. 1 2 Press to display the SET UP menu. Press to select “OSD LANGUAGE”. Press for more than 3 seconds. 3 Press to select “Shipping”. Press to display the Shipping menu.
Command list of Weekly Command Timer No.
Speci cations TH-60PF30U Power Source Power Consumption Rated Power Consumption Stand-by condition Power off condition Plasma Display panel Screen size (No.of pixels) Operating condition Temperature Humidity Applicable signals Color System Scanning format PC signals TH-65PF30U 110 - 127 V AC, 50/60 Hz 510 W 555 W Save OFF 0.7 W, Save ON 0.4 W Save OFF 0.7 W, Save ON 0.4 W 0.2 W 0.2 W Drive method : AC type 60-inch, Drive method : AC type 65-inch, 16:9 aspect ratio 16:9 aspect ratio 52.
This product has software installed partially licensed under the Free BSD LICENSE. Free BSD LICENSE regulations under the above specifications are as follows: (These regulations are set by the third party; therefore the original (English) regulations are stated.) Copyright © 1980, 1986, 1993 The Regents of the University of California. All rights reserved.