User’s Ｍａｎｕａｌ POS Workstation Model No. JS-950 Series Contents For USA / For CANADA English Read Me First …..….……..... 2 1.Getting Started 2.Operation 3.Appendix Before operating this product,please read the instructions carefully, and save this manual for future use.
■ For USA Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
English Read Me First Introduction Thank you for purchasing the JS-950 series Panasonic POS Workstation. This manual describes the instructions for the POS Workstation. Please read this manual carefully before using this product. List of JS-950 series Product Name Model Number.
1. Getting Started ■ Precautions [POS Workstation: JS-950 series] IMPORTANT Install a socket outlet adjacent to the equipment so that it will be easily accessible. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 1. Avoid Radio Frequency Interference Do not place the POS Workstation near a television or radio receiver. 2. Avoid Stacking Do not place heavy objects on the POS Workstation. 3.
■ Name of each part & function 1 4 2 3 5 6 1. Operator’s Display 2. Front SW cover 3. POP Holder 4. Rear Display 5. USB connector 6. Power SW Attention: Do not push Power SW by mistake when you insert the USB connector.
2. Operation ■ AC Cord Kit Installation 1. How to install the AC Cord (1) Carefully lay the Main Body Unit on a clear, flat surface as shown in figure (1). (2) Unpack the AC Cord, and then connect it to AC Inlet as shown in figure (2). (3) Fit the Cord Clamp to AC Cord, and fix it by attached screw as shown in figure (3)-1, 2 and 3. (4) Carefully replace the Main Body Unit in upright position as shown in figure (4).
■ Display Unit Installation Be sure to disconnect the power cable of the main block (POS Workstation) and confirm the power is “OFF” before the operation below. 1. How to install the display unit (1) Open the screw cover of the main unit (POS Workstation). (2) Hold the display unit with both hands and insert the connector section of the display unit into the connector inlet guide of the main unit slowly to connect the connector.
■ Storage Unit Installation Be sure to disconnect the power cable of the main block (POS Workstation) and confirm the power is “OFF” before the operation below. 1. How to mount the storage unit (1) Disconnect the 2 latches on the upper portion of the filter cover of the main unit by both hands, pull the cover toward you while pressing the cover downward at the same time, and remove the filter cover.
■ Rear Display Unit Installation Be sure to disconnect the power cable of the main block (POS Workstation) and confirm the power is “OFF” before the operation below. 1. How to mount the rear display unit (1) Loosen the thumbscrew on the lower portion of the rear cover at the rear display side of the main unit by hand, and remove the rear cover. * The thumbscrew shall be loosened until the screw rotates without resistance. (2) Prepare a rear display to be used. (The contents here explain the 2-line type.
2. How to replace the rear display (1) Loosen the thumbscrew on the lower portion of the rear cover of the main unit by hand, and remove the rear cover. * The thumbscrew shall be loosened until the screw rotates without resistance. (2) Disconnect the connector of the rear display from the connector of the main unit. (3) Loosen the 2 thumbscrews securing the rear display, and remove the rear display. * The thumbscrews shall be loosened until the screws rotate without resistance.
■ 2nd display unit Installation Be sure to disconnect the power cable of the main block (POS Workstation) and confirm the power is “OFF” before the operation below. 1. How to mount the 2nd Display Unit (1) Loosen the thumbscrew on the lower portion of the rear cover at the rear display side of the main block by hand, and remove the rear cover. * The thumbscrew shall be loosened until the screw rotates without resistance. (2) Prepare a 2nd display unit to be used.
2. How to replace the 2nd Display Unit (1) In case of 950SD010, disconnect VGA cable and speaker cable from I/O panel. (2) Loosen the thumbscrew on the lower portion of the rear cover of the main block by hand, and remove the rear cover. * The thumbscrew shall be loosened until the screw rotates without resistance. (3) Disconnect the connector of the 2nd Display Unit from the connector of the main block. (4) Prepare a new rear display.
■ ID module Unit installation Be sure to disconnect the power cable of the main block (POS Workstation) and confirm the power is “OFF” before the operation below. 1. Contents ID module 1pcs Peripheral screw 2pcs Screw 2pcs Cable cover Long type 1pcs Short type 1pcs (Use only Dallas KEY reader) Cable clamp 1pcs 2. How to mount the ID module unit (Please see the following pictures.) (1) Place the main unit to make the display unit at right angle to the mounting table.
Tighten the screw to clamp the cable and wiring the cable as shown in the fig. (10)-4. (11) Slide USB cable cover as shown in the fig. (11)-1. In case of Dallas KEY reader, slide the USB cable cover with care to avoid the cable from the rib of the USB cable cover as shown in the fig. (11)-2. (12) Put the supplied 2 peripheral screws in from the front side of the ID module unit and tighten the screws using a screwdriver from the rear side to secure it.
(11)-1 (11)-2 (12) Rib 3. How to replace the ID module unit (1) Remove Display Unit according to Display Unit Installation. (2) Prepare an ID module unit to be used. * The ID module unit is supplied with 2 pieces of peripheral screws, 2 pieces of screws, 1 piece of long cable cover, and 1 piece of short cable cover as accessories. (3) Slide the USB cable cover toward you while pushing both sides of the USB cable cover at the hinge section of the display unit inward to remove the cover.
3. Appendix ■ Specifications [Common Specifications] Environmental condition Item Operating Temperature Operating Humidity Strage Temperature Strage Humidity Specification +5°C – +40°C 15% RH – 85% RH (no dew) -30°C – +60°C 10%RH – 90%RH [POS Workstation: JS-950WS-・・・ ] Item Power Supply input Size Mass Standard Safty EMI & immunity Specification AC100V-240V, 50/60 Hz, 6.0A Approx. W250mm x D277mm x H351mm Approx. 7.
IO Connector layout (1) Bottom IO Connector layout COM 3 LINE-OUT (Powered) MIC Printer LAN ○○○○○○○○○○○○○ ○○○○○○○○○○○○ ○○○○○ ○○○○ USB1 USB2 COM 1 USB4(+24V) USB3(+12V) ○○○○○ ○○○○ ○○○○○ ○○○○ ○○○○○ ○○○○ COM 2 COM 4 (Powered) (2) Rear Display Connector Layout ○○○○○ ○○○○○ ○○○○○ C/D1 VGA C/D2 Top of main block 2nd Display T/P & VFD 4 Lines (COM6) VFD 2lines (COM6) (3) Front IO Connector layout SW & LED USB #5 LAN LED Soft Switch HDD LED Power LED 16
Outside drawing Main Body 12” Touch Screen 15” Touch Screen 17
[Touch Display Unit: JS-950D・・・・・ ] Item Size Mass Specification 12.1”: Approx. W320mm x D153mm x H256mm 15”: Approx. W364mm x D153mm x H300mm 12.1”: Approx. 3.4 kg 15”: Approx. 4.4 kg Outside drawing (1) 12.1” resistive TP Display, 12.
[Storage module Unit: JS-950H・・・・・ ] Item Size Mass Specification Approx. W171mm x D126.5mm x H34mm Approx. 0.8Kg (3.5”), 0.5Kg(2x CF) Outside drawing 3.
[Rear Display Unit: JS-950RD-・・・ ] Item Size Mass Specification Approx. W216.5mm x D29mm x H90mm Approx. 0.4Kg (2 Lines), 0.
[2nd Display Unit: JS-950SD-・・・ ] Item Note: Size Mass Specification It is not possible to use it together with the Rear Display Unit. Approx. W250mm x D72mm x H335mm Approx. 1.
[MSR Unit: JS-950MG-010 ] Item accessories Note: Size Mass Specification 2 pieces of peripheral screws 2 pieces of screws 1 piece of long cable cover 1 piece of short cable cover MSR, Dallas Key and Fingerprint can not be used at the same time. Approx. W63mm x D49mm x H140mm Approx. 0.
[Dallas Key Reader Unit: JS-950DP-010 ] Item accessories Note: Size Mass Specification 2 pieces of peripheral screws 2 pieces of screws 1 piece of long cable cover 1 piece of short cable cover - Work in virtual COM I/F - MSR, Dallas Key and Fingerprint can not be used at the same time. Approx. W73mm x D49mm x H100mm Approx. 0.
[Fingerprint Sensor Unit: JS-950FS-010 ] Item accessories Note: Size Mass Specification 2 pieces of peripheral screws 2 pieces of screws 1 piece of long cable cover 1 piece of short cable cover MSR, Dallas Key and Fingerprint can not be used at the same time. Approx. W73mm x D49mm x H100mm Approx. 0.
■ Cleaning Cleaning of outer case Light soil - Wipe case lightly with a dry, soft cloth. Heavy soil - Wipe case lightly with soft cloth pre-moistened with very diluted, mild detergent. Lightly wipe case dry with a dry, soft cloth. Cleaning of Display Wipe display gently with a dry, soft cloth to remove light dirt and dust. Do not wipe or press display hard, hit display or exert force on display as LCD in the display is breakable.
■ Operation Attention for capacitive touch screen (1) Do not touch it by finger nail, because capacitive touch screen can not recognize it. Touch it by finger tip. (2) Do not touch it during startup. It initializes touch screen during startup. If it is touched during startup, touch screen is not initialized correctly. (3) Be careful to not accidentally touch around display edges or press on display bezel as it can negatively affect display touch sensor accuracy.
Specifications and manuals are subject to change without notice. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United State of America and other countries. Intel and Celeron D are trademarks or registered trademarks of Intel Corporation in the United State of America and other countries. is a registered of trademark of Panasonic Corporation.
