Bluetooth Module Datasheet To nl y co nf id en ti al Model No.型号:TBM-QCC307B 版本 Version：V1.0 公布日期 Release Date: 2016-03-08 TONLY ELECTRONICS HOLDINGS LIMITED.通力电子控股有限公司 Address:Section 37, Zhongkai Hi-tech Development Zone, Huizhou Guangdong 516006, P.R.China 地址：中国广东省惠州市仲恺高新区惠风 6 路 37 号小区 网址 http://www.tonlyele.com ©2015 TONLY ELECTRONICS HOLDINGS LIMITED.
法律声明 Legal Notice, Disclaimer, Copyright 本手册是通力电子控股有限公司机密，未经能力电子控股有限公司的事先书面许可，任何人不得复制、 传播本手册的内容。通力电子控股有限公司不对由于使用本手册或执行本手册内容带来的损害负责。 本手册所涉及的知识产权归通力电子控股有限公司所有（或经合作商授权许可使用），任何人不得侵 犯。 本手册是按当前状态提供参考，本公司司保留随时更新本手册的权利,恕不另行通知。 本手册不对包括但不限于下列事项担保：适销性、特殊用途的适应性;实施该用途不会侵犯第三方的知 识产权等权利。 本文档在此未以禁止反言或其它方式授予任何知识产权使用许可，不管是明示许可还是暗 示许可。 本手册中提到的所有商标名称、商标和注册商标均属其各自所有者的财产，特此声明. al 本协议以中、英文两种语言制作，两种语言文本冲突时，任何时候均以中文为准。 This data sheet contains information that is confidential to TONLY ELECTRONICS HOLDINGS ti LIMITED.
TBM-QCC307B Bluetooth Module Datasheet 版本变更说明 Document Revision History Revision Date Author Checked by Description 版本 日期 作者 审核 描述 2018-8-18 huangzisheng liweixiong First release. To nl y co nf id en ti al V1.
目录 Table of Contents 法律声明 Legal Notice, Disclaimer, Copyright 文档变更说明 Document Revision History 目录 Table of contents 1.系统概览 System overview 1.1 通用说明 General Descriptions 1.2 性能特点 Features 2.产品描述 Production Description ti al 1.3 系统方框图 Block Diagram 引脚与功能说明 Pin Layout & Pin Description 4.电气特性 Electrical Characteristics id 3.
TBM-QCC307B Bluetooth Module Datasheet 1. 系统概览 System overview 1.1 通用说明 General Descriptions The QCC3007 module is a single-chip flash programmable dual mode Bluetooth v5.0 device with integrated application processor, low-power audio DSP, on-chip ROM and RAM, stereo codec, battery charger, switch-mode and linearregulators, and LED drivers. 1.2 性能特点 Features Bluetooth ® v5.
al Physical Dimensions To nl y co nf id en ti Pin descriptions PIN NO. Symbol Description Function GND Power supply and control Ground connections.
TBM-QCC307B Bluetooth Module Datasheet 30 、 33 、 37 、 47、58 Bi-directional with programmable AIO0 2 analog I/O. A CMOS output with a weak UART request to send, active internal pull-up. This pin can be used implement low RS232 Alternative function: hardware flow control where RTS UART_RTS 5 to PIO16: Programmable input / (request to send) is an active low output line 16. indicator. The UART interface requires an external Bidirectional RS232 internal pull-down.
CLK selected by SPI_PIO#. Programmable I/O line or debug SPI 17 SPI_CSB chip select (CSB) selected by chip select for SPI, active low SPI_PIO#. The RESET pin is an active high reset and is internally filter educing the 20 internal RESET low frequency clock oscillator .A reset will be performed between1.5 and 4.0ms following Reset if low. Pull low for minimum 5ms to cause a reset. RESET being active.
TBM-QCC307B Bluetooth Module Datasheet 31 1.8V_OUT Power supply and control 32 VDD_IO Power supply and control 1.8V DC/DC convertor output. Positive supply input for input/output ports. 3.3V bypass linear regulator 3V3_OUT 33 Power supply and control output. Also supply for USB port. Abi-directional USB data line with a selectable internal 1.5kΩ pull-up implemented as a current source (compliant with USB specification v2.0) USB_DN USB data minus.
53 AGND 54 SPK_RN Analogue Connect Analog Ground pins connections. Speaker SPK_RP 56 SPK_LN 57 SPK_LP negative, Speaker output positive, right Speaker output negative, left Analogue out Speaker output positive, left This pin can be used when not using a chip antenna or connector of the module. RF 59 output right Analogue out 55 Ground Bluetooth 50Ω transmitter output / receiver input Speakerphones 4.
TBM-QCC307B Bluetooth Module Datasheet Input Voltage 4.5 5 5.75 V Charge Current(CC mode) 194 200 206 mA Trickle Charge Current 10 mA Trickle Charge Threshold Voltage 2.92 V Regulated Output(Float)Voltage 4.2 V Stereo CODEC Analogue to Digital Converter Conditions Min Resolution Input Sample Rate, Fsample B/W=20Hz→20kHz A-Weighted THD+N<0.1% Ratio, SNR 8kHz 16kHz 32kHz 44.1kHz 44.
Frequency Band 2.402~ 2.48GHz Modulation Method GFSK；4/ΠDQPSK;8DQPSK Maximum Data Rate 1 Mbps/2 Mbps/3 Mbps Antenna External antenna Interface UART, PIO, AIO, SPI,PCM,SPI Operation Range >=10 meters(Free Space) Sensitivity -86dBm at 0.1% BER RF TX Power <=+10dBm 6.认证与法规信息 Certification& Regulation nl y co nf id en ti al The BQB Certification： To FCC This device complies with Part 15 of the FCC Rules.
TBM-QCC307B Bluetooth Module Datasheet ti This module can meet ROHS&REACH compliance.XXXX al 8.环保声明 Green Policy en 9.推荐过炉温度 RECOMMENDED TEMPERATURE REFLOW PROFILE The soldering profile depends on various parameters necessitating a set up for each id application. The data here is given only for guidance on solder re-flow. There are four zones: 1. Preheat Zone - This zone raises the temperature at a controlled rate, typically 1-2.5°C/s. nf 2.
al ti en Key features of the profile: ■ Initial ramp = 1-2.5°C/sec to 175°C ±25°C equilibrium id ■ Equilibrium time = 60 to 180 seconds ■ Ramp to maximum temperature (245°C) = 3°C/sec max. nf ■ Time above liquidus temperature (217°C): 45-90 seconds To nl y co ■ Device absolute maximum reflow temperature: 260°C 10.
For FCC: Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
The host Main unit is a SPHE8107H, It has 16Mb flash and needs 24.576MHz crystal of reference frequency. This chip is responsible to control DSP, Bluetooth, audio system and all the source of input Host .For the FCC certification, TBM-QCC307B is without shielding cover test, If the Host manufacturer adds a shield cover for the whole machine test, it needs to re-evaluate FCC spurious emission test and make C2PC.
Figure 2-1 For routing microstrip lines UNDERNEATH the NAD on layer 1, these ground cutouts internal to the NAD need to be accounted for in the stripline calculation. For example, consider the following stackup for a U2 PCB: Figure 3-1 Figure 3-1 Assume the U2 PCB Board above with a 4 layer stackup with ground cut away on layer 2 so the microstrip lines reference ground on layer 3.
26.74mils. Using an online impedance calculator, the line width under the NAD for a 53 ohm line is 16.87 mils .Figure 3-2 Figure 3-2 We can put in tray like for U2 SMD to 40-TMAX50-VFD2G. The PCB antenna on the design on 40-TMAX50-VFD2G is a Inverted F Antenna (IFA).( See Figure4-1) The IFA was designed to match an impedance of 50 ohm at 2.45 GHz. Antenna Gain ：3.0dBi. The antenna could require a matching network, It use the LC Circuit. R16 3.3nH 2,4-3 Figure4-1 C15 0.2Pf.
Figure 4-2 Figure 4-3 This 50ohm line(yellow)should be as short as possible to the IFA or
internal antenna feed point. See Figure 5-1 Figure 5-1 Mechanical Specifications of the Antenna. See Figure 6-1, Figure 6-2 Figure 6-1 H1 H2 H3 H4 H5 H6 H7 5.9mm 0.9mm 1.3mm 2.2mm 0.65mm 1.2mm 0.8mm H8 H9 L1 L2 L3 L4 L5 1.8mm 1.2mm 23.2mm 14mm 3.6mm 3.37mm 1mm L6 L7 L8 W1 W2 1mm 3.2mm 0.45mm 1.2mm 0.
Figure 6-2 Electrical Specifications of the Antenna Antenna S11 Parameter See Figure 7-1 7-2 Figure 7-1 Gain and efficiency Frequence/MHz 2402 2441 2480 Gain/dBi -0.114 0.4898 3.01 Efficiency/% 44.25% 45.92% 58.16% Figure 7-2 RF Antenna Layout Parameters • Signals should be routed along similar route path, but separated by ground trace. • Trace impedances should match the table, either as microstrip or stripline. • Total length for both signals should match the table.
