System Setup Guide Home Network System HUB Model No. KX-HNB600 Thank you for purchasing a Panasonic product. This document explains how to configure the hub and access it using a mobile device. These steps must be followed before you can use the system. For details about how to use the system, refer to the User’s Guide (page 17). Please read this document before using the unit and save it for future reference. For assistance, please contact us at 1-800-272-7033 or visit our Web site: http://shop.
Table of Contents Introduction Accessory information ..................................3 Important Information About this system .........................................6 For your safety .............................................6 Important safety instructions ........................7 Security cautions ..........................................7 For best performance ...................................8 Other information .........................................8 Setup Part names and functions .......
Introduction Accessory information Supplied accessories No. Accessory item/Part number A AC adaptor/PNLV236-0Y 1 B Telephone line cord/PQJA10075Z 1 C Wall mounting adaptor/PNKL1049Z1 1 A B Quantity C Additional accessories microSD card (not supplied) A commercially-available microSD card must be inserted into the hub in order to record images from cameras. The following types of microSD cards are supported.
Introduction Expanding the Panasonic Home Network System The Panasonic Home Network System is a wireless system that lets you create a powerful network of devices, such as cameras, sensors, and smart plugs, and control them all with an easy-to-use app. Compatible devices are explained below. For information about the Home Network app, refer to the User’s Guide (page 17). The maximum number of devices for each device type is listed below. Digital Cordless Handset (KX-HNH100: 6 max.
Introduction Smart Plug (KX-HNA101: 50 max.*2) R Can be turned on and off using the handset or Home Network app, when triggered by a sensor, or according to a schedule R Built-in overcurrent and overwattage detection for added peace of mind R Power consumption is logged for your reference *1 *2 Optional handsets may be a different color from that of the handset supplied as part of a pre-configured bundle.
Important Information About this system R This system is an auxiliary system; it is not designed to provide complete protection from property loss. Panasonic will not be held responsible in the event that property loss occurs while this system is in operation. R The system’s wireless features are subject to interference, therefore functionality in all situations cannot be guaranteed.
Important Information and 2.462 GHz with a peak transmission power of 100 mW. R Do not use the product in health care facilities if any regulations posted in the area instruct you not to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy. CAUTION Installation and location R Never install wiring during a lightning storm. R Never install telephone line jacks in wet locations unless the jack is specifically designed for wet locations.
Important Information stored in the product and remove the microSD card. Use only trusted repair services authorized by Panasonic. R Before disposing of the product, perform a factory data reset to erase any data stored in the product. Remove and erase the microSD card. R If your mobile device will no longer be used with the product, delete your mobile device’s registration from the product and delete the corresponding app from your mobile device.
Important Information R Do not use benzine, thinner, or any abrasive powder. Protecting your recordings R Do not remove the microSD card or disconnect the hub’s AC adaptor while reading or writing data to the microSD card. Data on the card could become corrupted. R If a microSD card malfunctions or is exposed to electromagnetic waves or static electricity, data on the card could become corrupted or erased. Therefore we recommend backing up important data to a computer or other device.
Setup Part names and functions A LED indicator You can use the LED indicator to confirm the hub’s status.
Setup 4 Connections *1 Insert the AC adaptor plug firmly into the DC jack. Secure the AC adaptor cord by wrapping it around the hook. Connect the AC adaptor to the power outlet. Insert the telephone line cord into the LINE jack and a single-line telephone jack (RJ11C) until you hear a click.*1 DSL/ADSL service users only: Connect your DSL/ADSL filter (not supplied).
Setup Power failure Compatible mobile devices R The hub will not work during a power failure. R The hub’s telephone features will not work during a power failure. We recommend connecting a corded-type telephone that does not use an AC adaptor to your telephone line. iPhone® 4 or later, iPad®, or iPad mini™ (iOS 6.0 or later) or an Android™ device (Android 4.
Setup 4 5 6 Change your mobile device’s Wi-Fi setting temporarily so that it connects to the hub directly. R Open your mobile device’s [Settings] app, tap [Wi-Fi], select “KX-HNB600_Panasonic”, enter “00000000” as the password, and then tap [Join]. R If more than 1 item named “KX-HNB600_Panasonic” is displayed, wait approx. 10 minutes and perform this procedure from the beginning. Start the [Home Network] app again.
Setup Initial setup for Android devices 1 Start the [Home Network] app. R If prompted, follow the on-screen instructions and select the appropriate region/country. R If prompted to select the device to be set up, tap [Hub]. 2 3 When prompted, tap [Set up the Hub]. 4 When prompted, press MWi-Fi SETUPN on the hub. R The LED indicator blinks in yellow. R The app temporarily changes your mobile device’s Wi-Fi setting so that it connects to the hub directly.
Setup Registering another mobile device In order to access the system from a mobile device, you must first register the mobile device to the hub. You can register up to 8 mobile devices to a hub. Confirm the following before you begin.
Setup 2 From the [Home Network] app home screen, tap [Settings]. 3 4 5 Tap [Device Registration]. Tap [Registration]. Select the type of device that you want to register. 6 Handset: Place the handset on the charger. Devices other than handset: Press and hold the registration button on the device you want to register until the device’s LED indicator blinks slowly in green. R When registration is complete, the hub sounds one long beep. Note: R If registration fails, the hub sounds several short beeps.
Appendix Wireless communication range (DECT) The wireless communication range of each device in the system from the hub is approximately 50 m (160 feet) indoors and approximately 300 m (1,000 feet) outdoors. Wireless communication may be unreliable when the following obstacles are located between the hub and other system devices.
Appendix 2 Wall mounting You can use the included wall mounting adaptor to wall mount the hub if desired. Note: R Make sure that the wall and the fixing method are strong enough to support the weight of the unit. 1 Connect the AC adaptor and the telephone line cord to the hub. R Secure the AC adaptor cord by wrapping it around the hook. Slide the wall mounting adaptor up until it clicks into place. R Make sure the “UP” mark on the wall mounting adaptor faces upwards.
Appendix 3 Mount the hub on a wall then slide down to secure in place. R Pass the AC adaptor cord and the telephone line cord through the groove (1) in the wall mounting adaptor. Wrap up the telephone line cord as shown to prevent the cord from being pinched. R This product is compliant with the following wall phone plate sizes (2 types). 2 83 mm (3 1/4 inches) 3 102 mm (4 inches) R Fit the slots of the hub onto the corresponding wall phone plate tabs for (4) and (5) respectively.
Appendix Specifications R Standards DECT: DECT (Digital Enhanced Cordless Telecommunications) Wi-Fi: IEEE 802.11b/g/n R Frequency range DECT: 1.92 GHz – 1.93 GHz Wi-Fi: 2.412 GHz – 2.462 GHz (channels 1 – 11) R RF transmission power DECT: 115 mW (max.) Wi-Fi: 100 mW (peak transmission power) R Encryption WPA2™-PSK (TKIP/AES), WPA™-PSK (TKIP/AES), WEP (128/64 bit) R Simplified configuration WPS (PBC) R Power source 120 V AC, 60 Hz R Power consumption Standby: Approx. 3.5 W Maximum: Approx. 4.
Appendix FCC and other information This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:ACJ----------. If requested, this number must be provided to the telephone company. R Registration No.............(found on the bottom of the unit) R Ringer Equivalence No. (REN).......0.
Appendix 2. Perform such activities in the off-peak hours, such as early morning or late evenings. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this device.
Appendix Customer services Shop Accessories! for all your Panasonic gear Go to http://shop.panasonic.com/support Get everything you need to get the most out of your Panasonic products Accessories & Parts for your Camera, Phone, A/V products, TV, Computers & Networking, Personal Care, Home Appliances, Headphones, Ba!eries, Backup Chargers & more… Customer Services Directory For Product Informa"on, Opera"ng Assistance, Parts, Owner’s Manuals, Dealer and Service info go to http://shop.panasonic.
Appendix Limited Warranty (ONLY FOR U.S.A.
Appendix Limited Warranty Limits and Exclusions This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage.
Notes 26 HNB600_(en_en)_0124_ver.201.
Notes 27 HNB600_(en_en)_0124_ver.201.
IMPORTANT! If your product is not working properly. . . A Make sure the AC adaptor is connected. B Use the Home Network app to access the User’s Guide and refer to the Troubleshooting section. Visit our Web site: http://shop.panasonic.com/support • FAQ and troubleshooting hints are available. For your future reference We recommend keeping a record of the following information to assist with any repair under warranty. Serial No.
Guía de configuración del sistema Sistema de red doméstico HUB Modelo n° KX-HNB600 Gracias por adquirir un producto Panasonic. Este documento explica cómo configurar el hub y cómo acceder a él desde un dispositivo móvil. Se deben seguir estos pasos para poder usar el sistema. Para obtener detalles sobre cómo usar el sistema, consulte la Guía del usuario (página 10). Lea este documento antes de usar la unidad, y guárdelo para consultarlo en el futuro.
Tabla de Contenido Configuración Nombres de los componentes y funciones ..........3 Led indicador ........................................................3 Conexiones ..........................................................4 Configuraciones de Wi-Fi® ...................................5 Registro de otro dispositivo móvil ........................8 Registro de otros dispositivos al hub ...................8 Apéndice Alcance de la comunicación inalámbrica (DECT) ..............................................
Configuración Nombres de los componentes y funciones A B C D E F G H I Altavoz Led indicador Clavija de corriente continua Clavija LINE MWi-Fi SETUPN Se usa durante la configuración inicial. Ranura para tarjeta microSD Se usa mientras inserta una tarjeta microSD. Retire la etiqueta cuando la inserte. M HANDSET/LOCATORN Se usa al registrar un auricular. También puede presionar este botón para ubicar un auricular perdido. M CAMERAN Se usar al registrar una cámara.
Configuración Conexiones *1 4 Inserte el enchufe del adaptador de corriente firmemente en la clavija de corriente continua. Asegure el cable del adaptador de corriente alterna enrollándolo en el gancho. Conecte el adaptador de corriente a la toma de corriente. Inserte el cable de línea telefónica en la clavija de LINE y la toma telefónica de una sola línea (RJ11C) hasta que escuche un clic.*1 Solo para los usuarios de servicio DSL/ ADSL: conecte su filtro DSL/ADSL (no incluido).
Configuración Falla en el suministro eléctrico Dispositivos móviles compatibles R El hub no funciona durante las fallas del suministro eléctrico. R Las funciones telefónicas del hub no trabajarán durante un corte de energía. Recomendamos que conecte un teléfono con cable que no utilice un adaptador de CA a su línea telefónica. iPhone® 4 o posterior, iPad®, o iPad mini™ (iOS 6.0 o posterior) o un dispositivo Android™ (Android 4.
Configuración 3 Cuando se le solicite, oprima MWi-Fi SETUPN en el hub. R El Led indicador parpadea en amarillo. 4 Cambie la configuración de Wi-Fi de su dispositivo móvil temporalmente para que se conecte directamente al hub. R Abra la aplicación [Configuración] en su dispositivo móvil, toque [Wi-Fi], seleccione “KX-HNB600_Panasonic”, introduzca “00000000” como clave y luego toque [Conectar]. R Si aparece más de 1 elemento llamado “KX-HNB600_Panasonic”, espere aprox.
Configuración Configuración inicial para dispositivos Android 1 Inicie la aplicación [Home Network]. R Si se le solicita, siga las instrucciones en pantalla y seleccione la región y el país apropiados. R Si se le solicita que seleccione el dispositivo que desea configurar, toque [Hub]. 2 Cuando se le solicite, toque [Configurar el Hub]. 3 Cuando se le solicite, oprima MWi-Fi SETUPN en el hub. R El Led indicador parpadea en amarillo.
Configuración Registro de otro dispositivo móvil Para acceder al sistema desde un dispositivo móvil, primero debe registrarlo en el hub. Puede registrar hasta 8 dispositivos móviles en un hub. Confirme lo siguiente antes de comenzar.
Configuración Uso de la aplicación 1 2 3 4 5 Inicie la aplicación [Home Network]. Desde la pantalla de inicio de la aplicación [Home Network], toque [Configuración]. Toque [Registro de dispositivos]. Toque [Registro]. Seleccione el tipo de dispositivo que desea registrar. 6 Auricular: Coloque el auricular en el cargador. Dispositivos que no sean auriculares: Mantenga presionado el botón de registro del dispositivo que desea registrar hasta que el Led indicador parpadee lentamente en verde.
Apéndice Alcance de la comunicación inalámbrica (DECT) El alcance de la comunicación inalámbrica de cada dispositivo en el sistema del hub es de aproximadamente 50 m (160 pies) en interiores y de aproximadamente 300 m (1,000 pies) en el exterior. Es posible que la comunicación inalámbrica no sea tan confiable cuando se encuentran los obstáculos siguientes entre el hub y otros dispositivos del sistema.
Apéndice Montaje en la pared Puede usar el adaptador de instalación en pared incluido para instalar el hub de dicha forma si lo desea. Nota: R Asegúrese de que la pared y el método de colocación sean lo suficientemente resistentes para soportar el peso de la unidad. 1 Conecte el adaptador de corriente y el cable de línea telefónica al hub. R Asegure el cable del adaptador de corriente alterna enrollándolo en el gancho. 2 Deslice el adaptador de instalación en pared hasta que encaje y haga clic.
Apéndice 3 Monte el hub en la pared y deslícelo para asegurarlo en su sitio. R Pase el cable del adaptador de corriente y el de la línea telefónica por la ranura (1) en el adaptador de instalación en pared. Enrolle el cable de línea telefónica como se muestra para evitar que se quede pillado. R Este producto es compatible con los siguientes tamaños de placas de los teléfonos (tipos 2).