User guide

ManualsBrandsPanasonic ManualsFansFV-20NLF1

INSTALLATION

INSTRUCTIONS

IN-LINE Fan

FV-10NLF1 FV-20NLF1

FV-30NLF1 FV-40NLF1

Panasonic

READ AND SAVE THESE INSTRUCTIONS

Please read the instrix:tkxis carefuly before atteripting to install.operate

or service the Panasonic IN-LINE Fan. Failure to comply with instructions

could result in personal injury and/or property damage. Please retain

for future reference.

Table of Contents

Supplied Accessories

__________________________________________________

Description__________________________________________________________

Dimensions_________________________________________________________

Specifications________________________________________________________

Unpacking__________________________________________________________

Pages

General Safety Information

____________

Installation I (Horizontally Between Joists)

_________

Installation II (On Ceilings/Joists).........................

......

Installation III (Vertically On Joists Or Pillars).

Mai ntenance

_____________________________

Product Service

___________________________

5-6

Summary of content (9 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FV-10NLF1 FV-20NLF1 FV-30NLF1 FV-40NLF1 IN-LINE Fan Panasonic READ AND SAVE THESE INSTRUCTIONS Please read the instrix:tkxis carefuly before atteripting to install.operate or service the Panasonic IN-LINE Fan. Failure to comply with instructions could result in personal injury and/or property damage. Please retain for future reference.
PAGE 2
SUPPLIED ACCESSORIES FV-10NLF1 FV-20NLF1 FV40NLF1 FV-40NLF1 Part name Illustration Quantity Bracket 2 Hartger 1 Bracket cover 2 Installation bracket 2 Extension bracket 2 Holder 2 (AssernOM on body) Long screw 10 Self-tapping screw Short screw 12 ec? 4 DESCRIPTION These Panasonic IN-LINE Fan models use a sirocco fan driven by a capacitor motor. The motor is designed to have an extended service life with reduced energy consumption, and a reduced noise level.
PAGE 3
DIMENSIONS FV-10NLF1 mnotf Part name No. No. Motor inspection panel Body Model No. A c B 0 e Pari rtame ® Brack«« cov«r Adapter installation bracket Ftn Extension bracket Junction box Bracket Jurtctlon box covor Holder F 8 Q H 1 j 097 340 240 440 200 36.1 321^1 242 0112 F\LtONLF<13 1 3«) (9 7/16) <17 S/16) (7 7«) (1 1«) (S/16) (12 5«-22 7«) (917/32) (43 13^6) ^13«2) 321-621 340 240 560 240 36.
PAGE 4
GENERAL SAFETY INFORMATION 1. Do not install this IN-LINE Fan wt>ere the temperature may exceed 6C ^140 T). 2. Make certain that the service supply voltage is 120V. 6OH2. 3. Follow all local electrical and satety codes as well as the National Electrical Code (NEC) and the Occupation Safety and Health Act (OSHA). 4. Always switch the power source off before workirtg 00 or near the fan or motor. 3. Protect the elecincal wires from sharp edges, os. grease, hot surlace$. chemicals, or other objects.
PAGE 5
INSTALLATION I (horizontally between joists) 1. Di$conodct the power to the receptacle before starting the installation. 2. Fix the hanger to the ceiling joist. Keep distance ’ A " between the hanger and ceiling board (table 1). Use two long screws to fasten the hanger. (Flg.1) Dintension: mm(inch) MODEL lONLFI 20NLFI MNLR 40NLFI 165 165 185 215 A (6|) (6|) (7|) (8|> (table 1) 3.
PAGE 6
INSTALLATION I (horizontally between joists) 6. Attach the IN-LINE Fan to a ioisi or a pillar with the kmg $crew$. (Fig.4) 7. Remove iunclion box cover and secure cortduii or wire holder to jurwtion box cover krx>ckout hole. {Fig.S) 8. Usirtg wire rtuts. connect house power wire as shown in the wictng diagram. 9. Replace junction box cover. CAUTION Mount Junction box cover carefully so that wires are not pinched. Wiring Diagram 10.
PAGE 7
INSTALLATION II (ON CEILINGS/JOISTS) 1. Attach installation bracket and bracket to the unit body. (Fig.6> CAUTION Inserì the installation bracket into the bracket covef attached to the panel. 2. Extend installation bracket and put the unK on the ceiling or (oist Secure with long screws. (Fig.7) OreUarduci UTQ SOW vlortQ icrtw 3. Remove junction box cover and secure oornkiit or wire holder to jur>ction box cover knockout hole. (Fig.S) 4.
PAGE 8
INSTALLATION III (VERTICALLY ON JOISTS OR PILLARS) Installing the IN-LINE Fan requires an accessible area (attic or a«r extraction apparatus) 1. Install the IN-LINE Fan using the first step deechbed in INSTALLATION II. 2. Extend insialation bracket arxl hang the unit on the joist or piller. Fix with the long screws. (Fig.8) CAUTION Be careful not to drop the unit. 3. Remove junction box cover and secure conduit or wire holder to junction box cover knockout hole. (Fig.S) 4.
PAGE 9
MAINTENANCE WARNING Disconnect power line betcxe procee<)íng with repairs or maint6r>ance. CAUTION 1. Never use beniene based thinner or similaf chemicals lor cleaning the 114-LINE Fan. 2. Do noi alow water to come imo contact with the motor. 3. Do not immerse resin parts in water where the temperature is over 60^(140 1. Remove inspection panel (take off the screws and pull). (Rq-S) 2. Clean nspecbon panel (do not immerse In water), wipe dry w^h cloth. 3.