Installation Guide

ManualsBrandsPanasonic ManualsBathWhisperGreen Select Pick-A-Flow 50/80 or 110 CFM Quiet Exhaust Fan, Flex-Z Fast bracket + dual 4 or 6 in. duct adapter

GENERAL SAFETY INFORMATION

PLEASE READ PRIOR TO INSTALLING THIS FAN

DESCRIPTION

UNPACKING

SUPPLIED ACCESSORIES

DIMENSIONS

WIRING DIAGRAM

FEATURE

INDICATION (PLUG ‘N PLAY FUNCTION DEVICES)

MOTION (PLUG ‘N PLAY FUNCTION DEVICES)

INSTALLATION (PLUG ‘N PLAY FUNCTION DEVICES)

INSTALLATION (NEW CONSTRUCTION)

INSTALLATION (RETROFIT)

MAINTENANCE (CLEANING)

SPECIFICATIONS

PRODUCT SERVICE

FV-0511VK 2 FV-0511VKS 2

FV-1115VK2

INSTALLATION INSTRUCTIONS

Ventilating Fan

Model No.

Contents

FV-0511VKS2

FV-0511VK2

FV-1115VK2

Representative models:

2-3

3-4

6-7

8-10

BACK COVER

PRACTICAL GUIDE TO INSTALLATION

BACK COVER

READ AND SAVE THESE INSTRUCTIONS

Thank you for purchasing this Panasonic product.

Please read these instructions carefully before attempting to install, operate or service

the Panasonic product. Please carefully read the “GENERAL SAFETY INFORMATION”

Failure to comply with instructions could result in personal injury or property damage.

Please explain to users how to operate and maintain the product after installation,

and this booklet should be presented to users.

Please retain this booklet for future reference.

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Ventilating Fan Model No.
PAGE 2
GENERAL SAFETY INFORMATION For Your Safety To reduce the risk of injury, loss of life, electric shock, fire, malfunction, and damage to equipment or property, always observe the following safety precautions. Explanation of symbol word panels The following symbol word panels are used to classify and describe the level of hazard, injury, and property damage caused when the denotation is disregarded and improper use is performed.
PAGE 3
GENERAL SAFETY INFORMATION CONTINUED Do not disassemble the unit for reconstruction. It may cause fire or electric shock. A statement to the effect that when the product is to no longer be used, it must not be left in place but remove, to prevent it from possibly failing. Ceiling joist must be subjected to static load more than five times the weight of the product. Do not install with a method which is not approved in the instructions. Do not use this fan with any solid-state speed control device.
PAGE 4
PLEA SE R EA D PR I O R T O I N ST A LLI N G T H I S FA N CO N T I N U ED the fans are built to run continuously at a pre-set lower level (FV-0511VKS2 and FV-0511VK2: 0, 30, 40, 50, 60, 70, 80, 90, 100 CFM; FV-1115VK2: 0, 50, 60, 70, 80, 90, 100, 110, 120 CFM). The setting is dependent on the size of the house and the individual wishes of the homeowner. It is crucial that the installer pre-set the lower setting during the installation. Please refer to the chart below and the switch indication on page 6.
PAGE 5
DIMENSIONS 3 1 1/4 (30) 1 1/2 (37) 4 1/2 (114) Unit: inches (mm) 9 8 3 3/8 (86) 13 (330) 5 7/8 (148) 3 7/8 (100) 2 5 7/8 (151) 12 (304) 10 1/4 (260) 4 6 3 3/8 (86) 13 13 1/4 ~ 15 1/2 (336~394) 16 1/2 ~ 18 3/4 (419~480) 21 1/4 ~ 23 1/2 (540~597) 5 1 6 5/8 (169) 7 7 FV-0511VKS2 7 1/2 (190) 12 11 FV-1115VK2 FV-0511VK2 FV-1115VK2 13 (330) No. 1 10 2 3 4 5 10 1/4 (261) 3 7/8 (100) 3 7/8 (100) 6 Part name Blade Grille Junction box No.
PAGE 6
FEATURE Optimum Ventilation Performance: Duct length, elbows and other factors increase static pressure which can hinder the performance of most ventilation fans. This fan utilizes Smart Flow microchip technology that monitors the static pressure in the system and speeds up or slows down the RPM of the fan depending upon the amount of resistance within the ducts. This feature allows the fan to perform as rated and avoid potential installation issues.
PAGE 7
INDICATION (PLUG ‘N PLAY FUNCTION DEVICES) CONTINUED Humidity selector range from aroun 30% to 80%. Factory setting is around 50%. Timer preset selector positions Timer [min] 0.5 1 2 3 5 10 20 30 60 Factory setting : 20 minutes. Position ” ” : For factory use 1. The product will run when environment humidity rise rapidly but not reach to the humidity setting, and stop after delay preset time. 2. Humidity setting selector is stepless change between 30 %RH ~ 80 %RH. 3.
PAGE 8
INSTALLATION (PLUG ‘N PLAY FUNCTION DEVICES) You can purchase the specified Plug ‘N Play devices that are explained on page 6-7 and install them in positions , 2 and 3 . Position can only be used with Multi-Speed module (model FV-0511VKS2 already have this control installed), position 2 and 3 can be used for any of the other optional control modules. 1. Remove the connector cover from position , 2 or 3 . 2.
PAGE 9
INSTALLATION (NEW CONSTRUCTION) CONTINUED 7. Refer to wiring diagram on page 5. Follow all the local electrical safety codes as well as the National Electrical Code (NEC). Using UL approved wire nuts, connect house power wires to ventilating fan wires. (Fig.5) W H I TE BLA CK RED GREEN Conduit Junction box Earth ground Wire nuts Switch box Live (Fan) CA U T I O N L N Neutral Mount junction box cover carefully so that lead wires are not pinched.
PAGE 10
INSTALLATION (NEW CONSTRUCTION) CONTINUED 12. Insert the other mounting spring into the slot as shown and mount grille to fan body. (Fig.10) Ceiling Mounting spring Gloves Grille CAUTION Fig.10 Mount grille carefully so that lead wire is not pinched. Attention: when the switch is at the “ON” position, wait 8 – 10 seconds for the Fan to start. This is a normal working condition.
PAGE 11
MAINTENANCE (CLEANING) WARNING Mounting spring Disconnect power source before working on unit. Grille Gloves Slot Fig.14 CAUTION Routine maintenance must be done every year. Please wear gloves during the cleaning work. Clasp Ceiling Never use gasoline, benzene, thinner or any other such chemicals for cleaning the ventilating fan. Do not immerse motor in water when cleaning. Do not soak resin parts in water over 140°F (60°C). Fig.
PAGE 12
PRACTICAL GUIDE TO INSTALLATION Properly insulate the area around the fan to or 6 inches roof jack, wall cap, minimize building heat loss and gain. (Fig.19) 4orinches soffit vent with backdraft damper Loose fill or batt insulation can be placed Mechanically connect duct to termination directly over the fan housing in the attic.