Operating Instructions

ManualsBrandsPanasonic ManualsPet FeederCPJNF01CW

USER’S MANUAL

Model No. CP JNF01

Smart Pet Feeder

Do not place this product in a high place to prevent product damage or pet safety issues from

falling. At the same time, in order to prevent pets knocking down the product, it is recommended

to place it in a corner or against a wall.

Keep it horizontal, do not overturn the product, otherwise it will cause the product working not

properly.

The inner wall of the bucket is washable with water, but the outer wall of the bucket, buttons, base

and other components are not washable with water.

If you want to stop using it, please unplug the power cord first, pour out the water, wash it and dry

it before saving.

If children use this device, please make sure to use it under the guidance of an adult.

Except for maintenance personnel, other people are not allowed to repair this product, so as to

avoid various accidental injuries.

The product has been tested at the factory, and it is normal for a little water stains on the parts.

Battery

• Do not use rechargeable type batteries.

• Danger of explosion if battery is incorrectly replaced.

Replace only with the type recommended by the manufacturer.

• Mishandling of batteries can cause electrolyte leakage and may cause a fire.

- Remove the batteries if you do not intend to use the unit for a long period of time or if the

unit is to be powered exclusively by AC power. Store in a cool, dark place.

- Do not heat or expose to flame.

- Do not leave the battery(ies) in a car exposed to direct sunlight for a long period of time with

doors and windows closed.

- Do not take apart or short circuit.

- Do not recharge alkaline or manganese batteries.

- Do not use batteries if the covering has been peeled off.

• Do not mix old and new batteries.

• Do not use different types of batteries at the same time.

• When disposing of the batteries, please contact your local authorities or dealer and ask for

the correct method of disposal.

If the product is abnormal, please stop using the product immediately and unplug the adaptor.

Please use in indoor environment and keep away from fire.

Pets biting wires may cause electricity leakage, please guide your pets do not do so.

Please stay away from other electrical equipment when using it to prevent damage caused by

accidental water splashing.

The product contains small parts, take care to prevent accidental swallowing.

AC adaptor

•

To reduce the risk of fire, electric shock or product damage,

- Insert the mains plug fully into the socket outlet.

- Do not pull, bend, or place heavy items on the lead.

- Do not handle the plug with wet hands.

- Hold onto the mains plug body when disconnecting the plug.

- Do not use a damaged mains plug or socket outlet.

•

The mains plug is the disconnecting device.

Install this unit so that the mains plug can be unplugged from the socket outlet immediately.

Unit

To reduce the risk of fire, electric shock or product damage,

- Do not let water or other liquids drip or splash inside the unit.

- Do not expose accessories (battery pack, battery charger, AC adaptor, SD memory card

etc.)to rain, moisture, dripping or splashing.

- Do not place objects filled with liquids, such as vases, on accessories.

- Use the recommended accessories.

- Do not remove covers.

- Do not repair this unit by yourself.

Refer servicing to qualified service personnel.

This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance by a person responsible for their

safety.

Children should be supervised to ensure that they do not play with the appliance.

This appliance must be used only with the AC adaptor supplied with the appliance.

WARNING

CAUTION

Disposal of Old Equipment

Only for European Union and countries with recycling systems

By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on

human health and the environment.

For more information about collection and recycling, please contact your local municipality.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

This symbol on the products, packaging, and/or accompanying documents means that used electrical

and electronic products must not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection

points in accordance with your national legislation.

Thank you for purchasing this product.

For optimum performance and safety please read these instructions carefully.

Please keep this manual for future reference.

.................................

.......................................

Parts Information

Installation Instructions

Instructions for Use

.....................................

Connect to the APP

.....................................

Washing Instructions

...................................

Indicator Status Description / Troubleshooting

.........

...................................

...

APP - Shared Device

........................

APP - Setting Up Feeding Plan

Package Contents

...........................................

......................................

Specifications

Panasonic reserves the right of final interpretation of

the instruction manual.

Table of Contents

Precaution for Use

......................................

APP - Disconnect the Feeder Distribution Network

..................................

Important Information

This product is only applicable to dry pet food, do not use with wet food, otherwise

it may cause equipment failure.

This feeder supports dry pet food up to 12mm in diameter (including freeze dried

pet treats).

Do not exceed the maximum line indication when replenishing pet food in the

bucket.

The difference in shape and size of the

dry pet food will cause a variation in the

amount of food dispensed per serving.

When assembling the feeder propeller

blade, ensure a click sound is heard

when pushing into the base (as shown

in the right image).

Recommendation on pet food types and pet food sizes

2 3

折页

成品尺寸：100x148mm

100mm

148mm

5 6

Desiccant

Install the desiccant

Press the middle position of the handle and turn the top cover

counterclockwise to the unlock mark and lift it up,open the desiccant box and

load the desiccant.Reinstall the top cover, press down on the middle of the

handle and tighten clockwise to the lock mark.

Short press the button once to turn on or off the ring light.

Press the button twice to deliver 1 portion of food (about 6-8g, depending on the

shape and size of dry food, the number of grams per serving may vary).

Manual Button Control

材质：70g书纸

Bucket

Distributional Bucket

Feeder Body

Keypad

Grain Outlet

Head Cover

Desiccant

Food Bowl

Bowl Tray

Power Interface

Suction Cups

Battery Cover

Bottom

View

Install the bucket

Align the round mark on the

side of the bucket with the

lock opening mark of the

feeder body, place the bucket

in the feeder body and rotate

the bucket clockwise to the

lock mark, then the

installation is completed.

Bucket

Feeder

Body

Lock Opening

Mark

Round Mark

Lock Opening

Mark

Round Mark

Lock Mark

Top and bottom

correspond and

then put in

Turn clockwise

and lock

After the power is turned on, the machine enters the standby state. Press

and hold the button for 3 seconds. At this time, the buzzer will sound, the

white light will flash twice quickly, and the machine will start up and perform

self-test. If it is the first use or the first use after restoring the factory

settings, the machine will directly enter the normal working state after the

power-on self-inspection is completed.

Starting Up

Press and hold the button for 3

seconds, the buzzer will sound

and the ring light will go out.

Shutdown

Short Press / Double Press

the button to operate

Positioning Convex

Plates

Bowl Holder

Positioning Groove

Cable Direction 1

Trace (The power cord can be snapped into

the bottom groove as shown in the picture)

Cable Direction 2

Power Interface

Suction Cup(fix the body)

After connecting to the APP, you can set the grain delivery plan in the APP, and

the food will be delivered regularly and quantitatively.

( Please refer to P12 for Connect to the APP )

APP Control

When the feeder is powered by batteries, the WIFI does not work, and the APP

cannot be connected. The pet treats can be delivered manually by double-clicking

the button, or according to the latest feeding plan previously set.

Battery Powered

Press and hold the button for 10 seconds, the white light will flash continuously,

and the distribution network information and feeding plan will be cleared.

Restore factory settings in working state

Precaution for Use Precaution for Use Parts Information

Installation Instructions Installation Instructions Instructions for UseInstallation Instructions

Instructions for Use

Read this product manual carefully before use. Once installed or used, it

means that you have carefully read and accepted the following safety

instructions. Our company is not responsible for any accidental losses

and will not assume any legal responsibility caused by violation

operations.

* It is recommended to replace the desiccant once a month, do not use if it is damaged.

* A generic desiccant can be used. Recommended specifications:

length < 100mm; width < 80mm;

Install the bowl

Put the food bowl into the bottom of the bowl holder, and insert the body from

top to bottom into the positioning groove of the bowl holder,.

Switch on the power supply

Take out the power adaptor, connect it to the power interface at the bottom of

the feeder body and turn on the power.

Fix feeder body5

Press the feeder so that the suction cup at the bottom of the feeder tightly

absorbs the ground to ensure that the ground is flat and clean.

( Avoid using on carpets or wet floors )

Household

AC socket

AC adaptor

(supplied)

13 14

Connect to the APP

Indicator Status Description / Troubleshooting

The ring light is always red.

Check the bucket is installed correctly.

The ring light flashing red quickly.

The ring light flashing red slowly.

The ring light flashing white slowly.

Please replace the battery.

The feeder cannot

connect to the Internet.

1. Check whether the machine is powered normally;

2. Check whether the machine bucket is installed normally;

3. Check if the machine is short of treats/stuck;

4. Check whether the WiFi password is correct;

5. Check whether the WiFi frequency is 2.4GHz,

if the WiFi frequency is 5GHz,

please try after changing the router.

Power on or off or press and hold the button again for

10 seconds to enter pairing mode.

1. Check whether the machine is short of treats, if there is a

shortage of treats, please replenish it in time;

2. If there is enough treats in the machine, please take out the

bucket to check whether the treats is stuck. After cleaning the

blockage, install the material bucket and power on again.

Symptom

No Power

Cause(s)

The AC adaptor is not connected to the

power supply or is not connected to a

power supply securely.

Please check that the AC

adaptor is connected

securely.

Remedy

Before resorting to maintenance service, please kindly check by yourself with the following chart.

The indicator light off (power on).

The white light flashes twice quickly.

The white light continue blink rapidly.

The white light breathing flicker.

The white light always on.

The red light always on.

The red light flashes slowly.

Treats shortage/ Stuck (Please judge according

to the amount of left treats in the bucket).

(when the battery is powered)

The power is less than 15%.

Normal working condition.

Barrel is not installed correctly.

The white light flashes twice quickly,

and the buzzer sounds.

The ring light goes out and the buzzer sounds.Shutdown

Power On Self Test

Prompt Network distribution

Network Distributing

Standby

Indicator Light Status Working Status

The red light flashes quickly for

5 seconds (interval 1 hour).

Search the "Smart Life" APP in major mobile application markets or scan the

QR code to download and install it.

After the installation is completed, register an account and log in to the APP.

Click "Add Device" on the home page, turn on the phone's Bluetooth and WiFi,

and ensure that the feeder is in the network distribution state, and bind the

device according to the APP prompt.

*Due to the upgrade and update of the APP, the actual operation may be slightly different from the

above description, please operate according to the current guidelines in the APP.

*A feeder can only be connected to one of the APP or the applet. If you need to switch from the APP

to the applet or from the applet to the APP, you need to disconnect the distribution network between

the APP and the feeder or the connection between the applet and the feeder distribution network.

Connect to the APP

*Panasonic Corporation assumes no responsibility for data and/or information leakage

that occurs during wireless transmission.

*Android phones are recommended to use Android 9.0 or above; Apple phones are

recommended to use ISO 10.0 or above; Hongmeng phones are recommended to use

Harmony 2.0 or above.

15 16 17 18

APP - Shared Device

APP - Setting Up Feeding Plan

Shared equipment can invite other members to control t he feeder through

the APP. Select the corresponding feeder on the home page to enter the

main feeding interface, click the edit icon in the upper right corner to find the

"Shared Device" column, click to enter the shared device page, click "Add

Share" to send to other members via SMS, and other members click the

invite link Device sharing is now completed.

( Note: The upper limit of sharing is 20 people. If the actual operation does

not match the above description, please refer to the actual operation. )

The APP allows users to set up a 7 day meal plan and automatically

dispense pet food at scheduled intervals by selecting preferred portion

size. (1= small portion & 5 = large portion)

The user can also manually dispense food via the APP at any time.

* The APP user interface may differ from the following visual example

due to APP updates.

To disconnect the distribution network connection between the feeder

and the device, click "Home" in the lower left corner, then click "..." in

the upper right corner to select the feeder, click "Remove Device" at the

bottom, and confirm that the feeder and the device are disconnected

from the distribution network open.

Specifications

Package Contents

Power Supply for main unit DC 5.0 V 1.0 A

Power Supply for adaptor 100-240 V~ 50/60 Hz 0.25 A

Power Consumption (normal use) 5 W

Power Consumption in standby modes < 0.5 W

Dimensions (L x W x H)

Unit 338 x 190 x 360 (mm)

Carton Box (individual) 215 x 215 x 440 (mm)

Net Weight with Adaptor 1.86

Operation Environment Temperature 5℃~40℃

Relative Humidity 5%~90%

Bluetooth version V4.2

Bluetooth frequency band 2.402~2.4835 GHz

Bluetooth maximum power 8.9 dBm

Wlan mode IEEE802.11B/G/N20

Wlan frequency band 2.40~2.4835 GHz

Wlan maximum power 18.2 dBm

Declaration of Conformity (DoC)

Hereby, "Panasonic Marketing Europe GmbH"

declares that this product is in compliance with

the essential requirements and other relevant

provisions of Directive 2014/53/EU.

The full text of the EU declaration of conformity

is available at the following internet address:

https://www.ptc.panasonic.eu/compliance-documents

Contact to Authorised Representative:

Panasonic Marketing Europe GmbH,

Panasonic Testing Centre,

Winsbergring 15, 22525 Hamburg, Germany

Panasonic Marketing Europe GmbH

Hagenauer Strasse 43, 65203 Wiesbaden, Germany

Manufactured by:

Version NO.：V1.0Web Site: http://www.panasonic.com

Authorized Representative in Europe:

Panasonic Marketing Europe GmbH

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Germany

1. Take down the bucket and unscrew the top cover, rotate and remove the

distributional bucket and grain stirring piece at the bottom of the bucket.

2. Clean and wash the bucket, blade, distributional bucket and bowl in turn.

3. After washing and drying, put back and install all parts in turn.

1. Take out the grain blender.

2. Rotate and remove the distributional bucket shell.

3. Remove the distributional bucket.

Washing Instructions

As the Picture Shows:

Food Bowl

Bowl Tray

AC adaptor

(supplied)

*Install Backup Batteries

Use a screwdriver to open the battery cover at the

bottom of the host, put 4 AA batteries into the battery

compartment, put the battery cover back and tighten

the screws.

*Reminder:

1. Spare dry batteries need to be purchased by

yourself, only alkaline dry batteries are

supported (R6P/R6C/R6S/LR6).

2. Make sure the installed battery is fully charged.

3. If the machine will not be used for a long time,

please remove all batteries to prevent potential

danger caused by battery liquid leakage.

Unique Code of Smart Pet Feeder ( Example )

CP-JNF01CW 2202 18 10001

Production Serial Number

Of The Day

Production Line No

Date Of Manufacture

Model Type

APP - Disconnect the Feeder Distribution Network

Smart Pet Feeder

1 1

Operating Instructions

Food Bowl

1 1 1

Bowl Tray Desiccant

DESICCANT

AC adaptor

Warranty

Important Information

Steps below serve as a guide to change the preferred name of your

Smart Pet Feeder. The App UI may vary depending on your device and

APP version.

Alerts will be displayed in your APP User Interface (UI) under

the following scenarios ;

if your Smart Pet Feeder is :

1) working using AC adaptor power supply.

2) paired to the device.

3) and connected to your network.

Additional warnings include:

Setup meal plan: select time, date, number of

portions, and then ‘Add’ or ‘Save’ settings.

Select portion size (1 = small

portion & 5 = large portion) and

manually dispense pet food.

i. When pet food is low ii. When pet food is jammed

Click on “Smart

Pet Feeder”

Select to “Edit”

icon

Rename and

“Save”

Select to

“Rename”

Select to “Edit”

icon

Summary of content (1 pages)

PAGE 1
折页成品尺寸：100x148mm 材质：70g书纸 100mm Precaution for Use USER’S MANUAL Smart Pet Feeder Model No. CP JNF01 Table of Contents 148mm Precaution for Use ...................................... 2 Parts Information ....................................... 4 Installation Instructions ................................. 5 Instructions for Use ..................................... 8 Washing Instructions ................................... 10 Indicator Status Description / Troubleshooting .........