080I Multi-purpose Digital Camera AK-HC910L Before attempting to connect, operate or adjust this product, please read these instructions completely.
For Your Safety $ DO NOT REMOVE PANEL COVERS BY UNSCREWING. To reduce the risk of electric shock, do not remove the covers. No user serviceable parts inside. Refer servicing to qualified service personnel. WARNING: • TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. • TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, KEEP THIS EQUIPMENT AWAY FROM ALL LIQUIDS.
For Your Safety Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis.
Contents For Your Safety...............................2, 3 Preface ...............................................5 Features..............................................5 Precautions.........................................6 Major Operating Controls and Their Functions .............................7, 8 _ Front Panel ...................................7 _ Top and Bottom Panels ............7, 8 _ Side Panel ....................................8 How to Install ......................................
Thank you very much for purchasing the multi-purpose digital camera. Preface This camera employs new 2/3q 2.2 million-pixel FIT CCD [1920(H)k1080(V)], realizing a compact light-weight system including the optical system. Also, the newly developed CCD having an FIT configuration suited for higher picture quality and the development of low-noise, high-speed amplifiers have enabled the realization of high sensitivity, high S/N ratio, and wide dynamic range.
Precautions DON’TS • Do not attempt to disassemble the camera or other units. In order to prevent electric shock, do not remove screws or covers. There are no user-serviceable parts inside. • Do not abuse the camera. Avoid striking, shaking, etc. The camera contains sensitive components which could be damaged by improper handling or storage. • Do not let the lens remain uncapped when the camera is not use. If the lens is not installed, do not leave the lens mount hole uncovered.
Major Operating Controls and Their Functions _ Front Panel 1 Lens Mount 2/3q standard bayonet type (B4 mount) lens is installed. 2 Lens Fixing Ring Knob Lens is fixed by turning the knob counterclockwise. 3 Cable Clamp Used to clamp the lens cable. 4 Lens Connector [LENS] Used to connect the camera cables of the lens. Pin No. Signal Pin No.
Major Operating Controls and Their Functions 6 Camera mounting hole (1/4-20UNC) 7 Camera mounting hole (3/8-16UNC) The screw holes can be used to secure the camera for installing it on camera housing, and when using a pan/tilt head or a tripod. _ Side Panel 8 Breaker [BREAKER] If the breaker is operated due to over-current or the like, check the cause and eliminate the trouble, then press the breaker button. 9 Zoom/Focus Connector [ZOOM/FOCUS] Used to connect the zoom/focus control cables of lens.
How to Install Be sure to ask the dealer for the installation, adjustment and connection of this equipment. _ How to set the lens • Standard 2/3q bayonet type (B4 mount) lens of any makers can be used*. 1 Turn the lens fixing ring knob counterclockwise to remove the lens mount cap. 2 Set the lens in place, and turn the lens fixing ring knob clockwise to precisely fix the lens. 3 Connect the lens cable to the lens connector.
How to Set Up the System (Connection) _ Connection of remote control box • Use multi-cable for the connection of Camera Controller AK-HRP900L and this unit. Coaxial Cable HD-SDI (5C-FB) D-sub 15-pin HD Monitor Multi-purpose Digital Camera AK-HC910L Multi-cable (5m) AK-HDMLTCA05 Video Input Signal YPbPr HD Monitor AC adapter External AW-PS505A sync signal (3 value sync) NOTE Note that the monitor output is attenuated and deteriorated if the cable is too long.
Multi-purpose Digital Camera Control System Configuration Remote (zoom/focus control) cable HD-SDI Remote controllable lens Coaxial Cable (5C-FB) D-sub 15-pin Multi-purpose Digital Camera AK-HC910L Multi-cable (5m) AK-HDMLTCA05 HD Monitor AC adapter AW-PS505A External sync signal (3 value sync) DC Power Cable D-sub 15-pin Camera Controller AK-HRP900L - 11 -
Multi-purpose Digital Camera Pan/Tilt Head Compatible System Configuration Remote controllable lens Remote (zoom/focus control) cable HD-SDI Coaxial Cable (5C-FB) Multi-purpose Digital Camera AK-HC910L Multi-cable (5m) AK-HDMLTCA05 HD Monitor AC adapter AW-PS505A External sync signal (3 value sync) Pan/tilt head AW-PH400 DC Power Cable Pan/tilt head control panel AW-RP400 AC adapter AW-PS505A - 12 - Camera Controller AK-HRP900L
Operation Procedure 1 Turn on the power of each 5 Adjust the black balance. equipment. 2 Properly adjust the light for the • This adjustment is needed when the camera is used for the first time or after leaving unused for a long time. 3 Adjust the flange back of the lens, • The adjustment is necessary when the ambient temperature is greatly changed or at the change of season. object. the iris and the focus.
How to Adjust _ Flange back adjustment (for zoom lens) The adjustment is to adjust the focus in all the range from the maximum zoom to the widest angle of the zoom lens. 1 Shoot a dark object to open the iris. 2 Adjust the distance from the object to 2m at least, then loosen the flange back fixing knob of the lens. 3 Set the lens to the maximum zoom and adjust the focus by turning the focus ring. 4 Set the lens to the widest angle and adjust the focus by turning the flange back adjust ring.
How to Adjust _ White balance adjustment Adjust the white balance after shooting a white object by at least 50% of the screen. NOTE: If the white signal level is over 100% or less than 50%, the white balance may not be normally adjusted. _ Colour temperature and white balance adjustment (reference) When carbon is burnt, it develops 10000K Blue sky various colours of light depending on the temperature.
How to Adjust _ Black balance adjustment • Adjust it with the lens closed. When the motor drive lens is controlled from the camera, adjusting the black balance causes the lens to be automatically closed. _ Gen lock adjustment When multiple cameras are used or the camera is combined with other equipment, it is necessary to adjust the phase for phase matching by external synchronization.
Setting of Menu Items _ Configuration of menu display screen Maintenance menu USER MENU Using condition setting menu Camera ID setting menu File managing & renewing menu - 17 -
Setting of Menu Items _ USER menu (Initial screen) The readout data at start of power supply is the data just before cutting off the power supply, and the operation is started with the data. 1. MAINTENANCE It sets various adjusting data. 2. SETTING It sets various modes. 3. CAM ID It sets the camera ID. 4. FILE MENU It executes file loading and saving, and makes the basic setting of data display. Menu operation is executed by the Camera Controller AK-HRP900L.
Setting of Menu Items ! Maintenance menu • Move the cursor (arrow mark) to the item to be adjusted and press the MENU key, then it enters the adjustment menu thereunder. • Move the cursor to MAINTENANCE and press the MENU key, then it returns to USER MENU. 1 Black shading correction menu • When MENU key is pressed at DETECTION, (BLK-SHD:ACTIVE) appears, then the lens is automatically stopped down and ABB operation is executed.
Setting of Menu Items ! Maintenance menu 2 Pedestal, gamma, flare adjustment menu M PED: Master pedestal can be adjusted only by turning the control panel VR. The R, G, B pedestal can be totally adjusted. R, B PED: R, B pedestal adjustment. Besides the master pedestal adjustment, R, B pedestal can be independently adjusted. It is not related to DATA REF. The numeral display after normal ending of ABB is “0” for both of R, B. M GAMMA: Master gamma adjustment. The R, G, B gamma can be totally adjusted.
Setting of Menu Items ! Maintenance menu 3 Knee&white clip adjustment menu M KNEE POINT: Master knee point adjustment. G, B, R knee point can be totally adjusted. R, B KNEE POINT: R, B knee point adjustment. Besides the master knee point adjustment, R, B knee point can be independently adjusted. M KNEE SLOPE: Master knee slope adjustment. G, B, R knee slope can be totally adjusted. R, B KNEE SLOPE: R, B knee slope adjustment.
Setting of Menu Items ! Maintenance menu 4 Gain adjustment menu The gain of R, B GAIN is adjusted. The difference from the state of being white-balanced can be adjusted. • The numeral value displayed after normal ending of AWB is “0” for both of R, B. 5 Detail adjustment menu DTL: Setting of valid/invalid of detail function. TOTAL DTL LVL: Horizontal and vertical detail level adjustment. H DTL LVL: Horizontal DTL component is adjusted independently of DTL adjusted by TOTAL DTL.
Setting of Menu Items ! Maintenance menu 5 Detail adjustment menu (continued from previous page) DTL (+): Setting of DTL at the edge in positive direction. DTL (–): Setting of DTL at the edge in negative direction. DTL CLIP: Setting of clip level of DTL edge. DTL SOURCE: Setting of video source [G, R, (3G+R) /4, (2G+R+B) /4, (G+B/2)] to create the detail. 6 Master gain, auto iris setting menu LOW GAIN: LOW setting of master gain. MID GAIN: MID setting of master gain. HIGH GAIN: HIGH setting of master gain.
Setting of Menu Items ! Maintenance menu (Super gain 1, 2, 3 are same menu.) 7 Super gain, Detail, Pedestal-offset level setting menu TOTAL GAIN: Total gain in analogue, pixel addition, and memory addition is displayed. ANLG GAIN: Gain setting in analogue. PIX MIX: Gain setting in horizontal pixel addition. Capable of setting 0/6 dB. H DTL LVL: DTL level setting of super gain. CRISP: Setting the function of reducing noise level of super gain. It is invalid when DTL level is “0”.
Setting of Menu Items ! Maintenance menu 8 Matrix menu Selection of table A, B or OFF. Adjustment of gain of each colour. 9 Colour correction 1 menu Adjustment of gain (saturation) and phase of each colour. qZ Colour correction 2 menu Adjustment of gain and phase of matrix.
Setting of Menu Items @ Setting menu - Menu for various settings. 1 Camera mode setting menu BLACK STRETCH: Setting of the function of expanding low-brightness analogue video level. It is set by ON/OFF. D5600K: It is able to make colour temperature correction of about 5600 degrees of electric colour temperature correcting file. It is set by ON/OFF. CABLE COMPE: Setting of video cable compensation. It is able to set 0/25/50m. SUP GAIN: It sets OFF/1/2/3 of MAX GAIN. CAM ID: Setting of camera ID display.
Setting of Menu Items @ Setting menu 1 Camera mode setting menu (continued from previous page) CAM ID POSI: It sets the display position of camera ID. 0: top left, 1: top right, 2: down left, 3: down right. MATRIX TABLE: It sets A, B or OFF of Matrix table. COLOR CORRECTION: Setting of matrix ON/OFF. STATUS: It sets displaying/not displaying the status when AWB/ABB is executed. 2 Electronic shutter setting menu SHUTTER MODE: It selects the shutter operation. ON/SYNCHRO/OFF can be selected.
Setting of Menu Items # Camera ID setting menu $ File managing and renewing menu - File operation menu : blinking display. 1 The file selected by FILE is loaded. It can be selected from [PRESET/USER1/USER2 /CURRENT]. When desired to return to the previous data after loading other file, select “CURRENT”.
Setting of Menu Items $ File managing and renewing menu - File operation menu (continued from previous page) 2 When saving the current data, two files (USER1/USER2) can be saved. Select the file by “SAVE FILE?” Select “USER1” and move the cursor to SAVE and press the MENU key, then the item menu is displayed. 3 SAVE IN USER1. OK? “YES” and “NO” are displayed. Move the cursor from “NO” to “YES” and check that “YES” blinks.
Outside Dimension Diagram 12 125 10 unit: mm 110 15 160 - 30 - 20
Specifications & Accessories _ Specifications Supply voltage: DC 12V (supplied from D-SUB 15 pins) Power consumption: 22 W 1 indicates safety information. Image pickup device: System: Resolving optical system: Optical filter: 2/3q 2.2 million-pixel FIT CCDk3 GBR image pickup system F1.4 prism CC: clear, 4300K, 6300K, cross ND: 100%, 25%, 6.3%, 3.2% Lens mount: Bayonet type Output spec.: SMPTE 274M Sensitivity: F10, 2000Ix, 3200K, white reflection rate 89.
Matsushita Electric Industrial Co., Ltd. Web Site: h t t p : / / w w w . p a n a s o n i c . c o .