July, 2019 RV938 RAVEL DESK Assembly Instructions - Important: Carefully unpack and identify each component before attempting to assemble. Refer to parts list. Please take care when assembling the unit and always set the parts on a clean, soft surface. If you require any assistance with assembly, parts or information on other products, please visit our website: www.officestar.net or call or write us.
1. Do not use this product unless all screws and bolts are securely tightened. 2. Check that all screws and bolts are tight every three months or as needed. 3. Dispose of packing material properly. Do not use plastic cover as head covering. It may cause suffocation. 4. Do not use this product as a stepladder. 5. Use this product for its intended purpose only. 6. FOR INDOOR RESIDENTIAL USE ONLY.
PARTS (A) Top Panel (1 PC) (B) Left Side Panel (1 PC) (C) Divider Panel (1 PC) (D) Right Frame (1 PC) (E) Bottom Panel (1 PC) (F) Shelf (2 PCS) (G) Right Cross Rail (1 PC) (H) Left Back Rail (2 PCS) (I) Right Back Panel (1 PC) (J) Left Back Panel (1 PC)
PARTS (K) Front Drawer Panel (1 PC) (L) Drawer Left Side Panel (1 PC) (M) Drawer Right Side Panel (1 PC) (N) Drawer Back Panel (1 PC) (O) Drawer Bottom Panel (1 PC) (P) Drawer Support (1 PC) IMPORTANT NOTE: Use hand tools only for assembly as power tools may cause damage. Rubber mallet also needed for assembly (not provided). Phillips Screwdriver also needed for assembly (not provided).
HARDWARE LIST NO DRAWING DESCRIPTION QUANTITY 1 Screw 12 PCS + 2 EXTRA 2 Screw 20 PCS + 2 EXTRA 3 Screw 10 PCS + 2 EXTRA 4 Cam Screw 4 PCS + 1 EXTRA 5 Cam Screw 5 PCS + 1 EXTRA 6 Cam Screw 17 PCS + 2 EXTRA 7 Cam Nut 4 PCS +1 EXTRA 8 Cam Nut 22 PCS + 2 EXTRA 9 Wooden Dowel 2 PCS 10 Wooden Dowel 22 PCS + 2 EXTRA 11 Drawer Rail 1 PC 12 Drawer Rail 1 PC 13 Drawer Rail 1 PC 14 Drawer Rail 1 PC 15 Plastic Cap 12 PCS + 2 EXTRA 16 Shelf Pin 8 PCS + 1 EXTRA
STEP 1 (6) (B) (10) FULLY TIGHTEN CAM SCREWS (6). STEP 2 (6) (C) (11) (1) (10) (6) (C) (11) FULLY TIGHTEN CAM SCREWS (6) & SCREWS (1).
STEP 3 (H) (H) (I) (10) (G) STEP 4 (5) (1) (D) (13) FULLY TIGHTEN CAM SCREWS (5 & 6) AND SCREWS (1).
STEP 5 (15) (8) (B) (H) (H) FULLY TIGHTEN CAM NUTS (8). STEP 6 (B) (15) (8) FULLY TIGHTEN CAM NUTS (8).
STEP 7 (C) (3) (B) (E) FULLY TIGHTEN SCREWS (3). STEP 8 FINISHED EDGE (15) (8) (C) FULLY TIGHTEN CAM NUTS (8).
STEP 9 (6) (A) FULLY TIGHTEN CAM SCREWS (6). STEP 10 (A) (G) (B) (15) (8) (I) (C) FULLY TIGHTEN CAM NUTS (8).
STEP 11 (A) (G) (15) (8) (I) (D) FULLY TIGHTEN CAM NUTS (8). STEP 12 1mm (A) 1mm DETAIL A (2) (J) (I) ALIGN LEFT BACK PANEL (J) TO ASSEMBLY (SEE DETAIL A). FULLY TIGHTEN SCREWS (2).
STEP 13 FINISHED EDGE (F) (16) STEP 14 (4) (K) (M) (L) (9) FULLY TIGHTEN CAM LOCK SCREWS (4).
STEP 15 (L) (15) (7) (M) (P) FULLY TIGHTEN CAM NUTS (7).
STEP 17 (N) (L) (3) (P) (M) FULLY TIGHTEN SCREWS (3). STEP 18 (14) (14) (1) (12) (M) (N) (L) (12) FULLY TIGHTEN SCREWS (1).
STEP 19 (K)
