INSTRUCTION MANUAL DSMX Transmitter (EU Version) 6 CHANNEL TRANSMITTER
Introduction Thank you for purchasing our product, an ideal radio system for beginners or experienced users alike. Read this manual carefully before operation in order to ensure your safely and the safely of others or the safe operation of your system. If you encounter any problem persists, contact your local deal or visit our service and support website for www.hobbyking.com Safely 1. Safely Symbols Pay close attention to the following symbols and their meaning.
Do not touch any part of the model that may generate heat during operation. The engine, motors and speed control may be hot and cause injury. Do not grasp the transmitter’s antenna during flight. It may be degraded the quality of the radio frequency transmission. Make sure the model flies within a certain distance range. FCC statement Note: This device complies with part 15 of the FCC Rules.
Transmitter Overview S6 S8 S5 S7 S1 S4 S2 S3 Lanyard hook Throttle/Rudder Elevator/Aileron Trim Trim Trim Trim Binding key Wheel Cancel key LCD Antenna Handle Trainer port Grip Bettery compartment Installation and removal of the transmitter battery The T6i transmitter is designed to work with four x (LR6) AA alkaline dry cell batteries 6 CHANNEL TRANSMITTER DIGITAL PROPORTIONAL RADIO CONTROL SYSTEMPROGRAMABLE SYSTEM 4
Push and slide down Battery cover Binding procedure (Take ORX receiver as example) 1. Install a bind plug into BIND connector. In case if you want to disable telemetry function on the receiver, install second bind plug into THRO connector. 2. Apply power to the receiver. It can be from 3.7 to 9.6 volts DC. Please refer to indicator on the receiver for the correct pinout (GND, VCC, SIGNAL) 3. You will see the orange LED rapidly blinking. That means the receiver is in Bind mode. 4.
5. The system will display “RX Binding..”. After successfully binding, the transmitter will automati cally exit this binding menu. 6. Remove the bind plug(s) from the BIND on the receiver NOTICE: Remove the bind plug to prevent the system from entering bind mode the next time the power is turned on. Sometimes servo inputs or ESC-s with high input load can cause receiver binding in “No telemetry” mode. During this binding you will see both orange and red LED blinking.
End points End points controls the low and high travel limits for each servo. For each channel the user can set the low and high limits. This ensures that the channel date for the servo is consistent with structural design and performance requirements to ensure the best results. Adjustment can be made for any channel. Setup: 1. Press the Roller button to select channel 2. The right-side value represents high limit / The left-side value represents low limit.
Dual rate/exp. This function is use to add a curve to the channels input. This means that the ratio of stick to channel movement can be changed in order to add or remove sensitivity at different parts of the sticks range of motion. It can available on the aileron, elevator and rudder channels. This function sets the rate and exp. for channels 1, 2 & 4 and the switches from Sw 1 to 8, Disable and ON Rate – Adjust the slope of the curve.
Setup: 1. Select “Throttle Curve” in main menu 2. Press the Roller button to select point L, 1, 2, 3, H. 3. Move the wheel left or right to change the point’s value (position) on the graph. 4. Press and hold the wheel to save an exit 5. Or press the cancel key to exit without saving. Throttle cut The throttle cut function is used for gas powered engines. When the chosen switch is toggled the throttle will drop below the set minimum in order to cut the engine. Setup: 1.
Mixes This function is used to create a mix between channels. For example, if at low throttle some automated flap movement is desired, it is possible to create a mix to do this. The difference between curve mixes and linear mixes is that it is no possible to create a nonlinear relationship between the master and slave. Setup: 1. Select “Mixes” in main menu 2. Press the roller button to select below options Mix# 1 to 6 Mix is – on / off Master – Channel 1 to 6 Slave – Channel 1 to 6 Pos.
2. Press and hold the Binding key to activate Range test Timer This function is used to keep track of time to reduce the risk of aircraft running out of battery/fuel and crashing. These are very useful when used in conjunction with a toggle. There are two choices for timer: Engine timer and Multi. Timer. Engine Timer counts the time when throttle value exceeds the set value. Both timers can be reset by touching the “Reset”, and engine timer can modify throttle value by moving Roller button.
Up Mode: Reset - Press and hold the cancel key to reset the timer if needed, then press the Roller button Thr. pos - Turn the Roller button to change the throttle trigger point. Press and hold the Roller button to save an exit or press the cancel key to exit without saving Down Mode: Reset - Press and hold the cancel key to reset the timer if needed, then press the Roller button Thr. pos - Turn the Roller button to change the throttle trigger point. Set up – Turn the Roller button to set the time in min.
Reset Switch – Turn the Roller Button to reset the switch 1 to 8 or None to position up, mid or down Press and hold the Roller button to save an exit or press the cancel key to exit without saving Down and up Mode: Timer State – Turn the Roller button to select “Stop” or “Run”. If “Run” is selected, the timer is counted up Reset - Press and hold the cancel key to reset the timer if needed, then press the Roller button Set up – Turn the Roller button to set the time in min. and sec.
RX: This setting is used to sound an alarm when the receiver battery voltage drops dangerously low Batt: This setting is used to sound an alarm when the voltage out of range Temp: Temperature information is came from an optional Temperature sensor. If it becomes higher or lower than the settling, an alarm will alert you Current information is came from a optional Current sensor. If it becomes higher or lower that the settling. And alarm will alert you.
Aux. channels This function allows users to set auxiliary channels. Every channel that is not assigned during the model setup will be set as an AUX channel. AUX channels can be used to control various extra features on an aircraft including landing gear, brakes, lights. Setup: 1. Press the wheel to source between aux channel 5 and 6.(And after channels not in use) 2. Move the wheel to assign a switch. 3. Press and hold the wheel to save an exit, or press the cancel key to exit without saving.
Model setup The mode setup function is used to set up, manage and delete models. Model Select: Selects a model from memory. 1. Use the wheel to select a memory slot for the model. 2. Press and hold the wheel to save an exit, or press the cancel key to exit without saving. Type select: Change between airplane/glider and different helicopter types and multicopter. 1. Use the wheel to select the model type. 2. Press and hold the wheel to save an exit, or press the cancel key to exit without saving.
Model Reset: Resets a model to factory default settings. 1. Use the wheel to select a memory slot for the model. 2. Press the wheel to select and then move the wheel to select yes and press the wheel again. 3. If needed press the cancel key to exit without saving. Model copy: Copies a model from one memory slot to another. 1. Use the wheel to select a model to copy and press the wheel. 2. Use the wheel to select a memory slot to copy to. 3. Press and hold the wheel and then move the wheel to select yes. 4.
Elevon: The elevon function is used for planes that combine the elevens an ailerons together. Setup: 1. Use the wheel to enable the elevon function and press the wheel. 2. Use the wheel to set the first channels position and press the wheel. 3. Use the wheel to set the second channels position. 4. Press and hold the wheel to save an exit, or press the cancel key to exit without saving. V Tail: The V-tail function is used for planes that have no elevators and has a V-tail rudder configuration.
3. If needed set the flaperon to a switch using the wheel then press the wheel. 4. Choose the flaperon position. 5. Press and hold the wheel to save an exit, or press the cancel key to exit without saving. Bind: The transmitter and receiver have been pre-bound before delivery. If you are using another transmitter or receiver, follow the steps below to bind the TX and RX: 1. Connected the bind cable to the bind port of the receiver. 2. Connected the power to any other port.
Model setup Swashplate mix Adjust the motion range of these three functions to achieve the desired maneuverability. Refer to your models manual to ensure best results. This function is used to edit the pre-programmed mix control of the helicopter’s aileron, elevator and pitch. Use the wheel to change the aileron, elevator and pitch values. Setup: 1. Use the wheel to change the aileron value, then press the wheel. 2. Use the wheel to change the elevator value, then press the wheel. 3.
ARM The function ensures a model will not fly until a switches has been toggled. Setup: 1. Use the wheel to select a switch or on, then press the wheel. 2. Use the wheel to select a channel. 3. Press and hold the wheel to save an exit, or press the cancel key to exit without saving. System setup User name Set a username for your system. Setup: 1. Use the wheel to select a character and press the wheel to enter it. 2. Press and hold the wheel to save and exit, or press the cancel key to exit without saving.
Student mode This function is used when another system is connected as a master (trainer), when this mode is active all settings will be bypassed and the system will only function through the master. Press and hold the wheel and move the wheel to select yes. Sticks mode There are 4 available stick modes, each stick mode changes the stick functions.
System settings Firmware Ver. This function shows information about the transmitters currently installed firmware version. Firmware update The function is for updating the system firmware. Setup: 1. Download the latest firmware from www.hobbyking.com 2. Open the firmware update on a computer and connect the system via USB cable. 3. Select [Firmware Update] from the systems function menu.
RF module update This function is for updating the RF module. Setup: 1. Connect the system via USB cable. 2. Press the wheel, the system will show a prompt, “ This will enter RF module update mode and halt other functions” with an option to continue, Select “Yes”. 3. Open the software update on a computer . Select COM port , then press “Connect”. 4. Press “Open file” to choose the file and press “Write” to enter the update mode. 5. Restart your system. Factory reset Resets the system to factory settings.
