Datasheet

© TT electronics plc
General Note
TT Electronics reserves the right to make changes in product specicaon without
noce or liability. All informaon is subject to TT Electronics’ own data and is
considered accurate at me of going to print.
OP505, OP505W, OP506, OP506W
OP535, OP705
Issue B 08/2016 Page 3
OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: [phone]
www.optekinc.com | www.electronics.com
Absolute Maximum Rangs ( T
A
= 25° C unless otherwise noted)
Storage & Operang Temperature Range -40°C to +100° C
Collector-Emier Voltage (OP505, OP506, OP505W, OP506W, OP705) 30 V
Collector-Emier Voltage (OP535) 15 V
Emier-Collector Voltage (OP505 and OP506 series only) 5.0 V
Lead Soldering Temperature (1/16 inch (1.6 mm) from case for 5 seconds with soldering iron) 260° C
Power Dissipaon
100 mW
(2)
Emier Reverse Current (OP705 series only) 10 mA
Collector DC Current (OP705 series only) 30 mA
Electrical Specicaons
Electrical Characteriscs ( T
A
= 25° C unless otherwise noted )
OP505, OP506, OP505W, OP506W, OP705
SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS
I
C(ON)
On-State Collector Current
OP505A, OP506A
OP505B, OP506B
OP505C, OP506C
OP505D
4.30
2.15
1.10
0.55
-
-
-
-
-
5.95
3.00
-
mA V
CE
= 5 V, E
e
= 0.50 mW/cm
2
, Note 3
OP705A 3.95 - 12.00
mA V
CE
= 5 V, E
e
= 0.50 mW/cm
2
, Note 3
OP505W, OP506W 0.10 - -
mA V
CE
= 5 V, E
e
= 0.75 mW/cm
2
, Note 3
Collector-Emier Saturaon Voltage
OP505, OP506, OP705
- - 0.40 V
I
C
= 250 μA, E
E
= 0.5 mW/cm
2
, Note 3
V
CE(SAT)
OP505W, OP506W - - 0.40 V
I
C
= 50 μA, E
E
= 0.75 mW/cm
2
, Note 3
I
CEO
Collector-Dark Current - - 100 nA
V
CE
= 10 V, E
E
= 0
V
(BR)CEO
Collector-Emier Breakdown Voltage 30 - - V
I
C
= 100 μA, E
E
= 0
V
(BR)ECO
Emier-Collector Breakdown Voltage
OP505, OP506
5 - - V I
E
= 100 μA, E
E
= 0
OP705 0.4 - - V I
E
= 100 μA, E
E
= 0
∆I
C
/∆T Relave I
C
Changes with Temperature - 1.00 - % / °C V
CE
= 5 V, E
E
= 1.0 mW/cm
2
E
KP
Knee Point Irradiance (OP705) - 0.02 - mW/cm
2
V
CE
= 5 V, Note 4
Notes:
(1) RMA ux is recommended. Duraon can be extended to 10 seconds maximum when ow soldering. A maximum of 20 grams force may be applied
to the leads when soldering.
(2) Derate linearly 1.33 mW/° C above 25° C.
(3) Light source is an unltered GaAs LED with a peak emission wavelength of 935 nm and a radiometric intensity level, which varies less than 10% over
the enre lens surface of the phototransistor being tested.
(4) The knee point irradiance is dened as the irradiance required to increase Ic(on) to 50 μA.