Operation Manual

26
Connecting -compatible AV Components
The terminal on the TX-NR801/TX-NR801E is for
connecting other Onkyo components equipped with the
same
terminal. When a component is connected to
the
terminal, it can be operated by the remote
controller supplied with the TX-NR801/TX-NR801E. In
addition, when you connect a component to the
terminal, you can also perform the system operations
given below.
Power on/ready function
When the TX-NR801/TX-NR801E is in the standby
state, if an
-connected component is turned on, the
TX-NR801/TX-NR801E also turns on and the input
source selected at the TX-NR801/TX-NR801E
automatically switches to that component.
Be aware that this function will not work if the power
cord for the
-connected component is connected to
the AC OUTLET on the TX-NR801/TX-NR801E, or if
the TX-NR801/TX-NR801E has already been turned on.
Direct change function
When the play button is pressed on an
-connected
component, the input source selected at the TX-NR801/
TX-NR801E automatically changes to that component.
Power off function
When the TX-NR801/TX-NR801E is placed in the
standby state, all
-connected components are also
automatically put into the standby state.
Also, if you press the ON button on the TX-NR801/
TX-NR801E remote controller while the TX-NR801/
TX-NR801E is turned on, all
-connected
components (DVD players, CD players, MD recorders,
tuners, etc.) are also turned on.
To connect components using the
terminal, simply
connect a remote control cable from this
terminal to
the
terminal of the other component. An remote
control cable with a 1/8 inch (3.5 mm) miniature two-
conductor plug comes with every cassette tape deck,
compact disc player, MD recorder, and DVD player that
has an
terminal.
• When performing operations with
-connected
components using the
system, do not use the
remote zone (Zone 2).
• For remote control operation, the audio connection
cables must also be connected.
• If a component has two
terminals, you can use
either one to connect to the TX-NR801/TX-NR801E.
The other one can be used to daisy chain with another
component.
• With Onkyo DVD players, you can enter the pre-
program code so that you can operate the DVD player
directly with the remote controller without connecting
the
terminals (See page 82).
AUDIO
VIDEO
S VIDEO
MONITOR
OUT
R
L
IN
IN
IN
IN
IN
ZONE 2
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
AUDIO
VIDEO
S VIDEO
COMPONENT
VIDEO
Y
P
B
PR
OUTPUT
INPUT 1
Y
P
B
PR
INPUT 2
Y
P
B
PR
FRONT SPEAKERS
L
RL
R
SURR SPEAKERS
CENTER
SPEAKER
R
L
R
L
OUT
OUT
OUT
I R
IN
OUT
REMOTE
CONTROL
PHONO
DIGITAL
IN
PRE OUT
DIGITAL
OUT
OPT
OPT
2
1
2
1
2
3
FRONT
SUB
SURR
R
L
AUDIO
R
L
CD
TAPE
R
L
AUDIO
1
3
GND
SURR
BACK/
ZONE 2
IN
OUT
COAX
R
L
MULTI CH
INPUT
FRONT
SUB
SURR
SURR
BACK
CENTER
R
L
R
L
AM
FM
75
CENTER
ANTENNA
IN
IN
(
Net
-
Tune
)
ETHERNET
4 OHMS MIN. OR
6 OHMS MIN.
/SPEAKER
CAUTION
:
SPEAKER
IMPEDANCE
SEE INSTRUCTION
MANUAL FOR
CORRECT SETTINGS.
MO
REMOTE
CONTROL
L
R
ANALOG
OUTPUT
DIGITAL OUT
OPTICAL
AUDIO
R
L
IN
DIGITAL
IN
OPT
1
REMOTE
CONTROL
Onkyo DVD player
Remote
control
cable
Connections for Remote Control ( )
REMOTE
CONTROL
TX-NR801/
TX-NR801E
Ex: Onkyo CD player
connector
connector
Ex: Onkyo cassette tape
deck
Remote control cable