Owner's Manual
60
Controlling other components connected to
the DVD Changer Receiver
--
/
---
SEND/LEARN
TOP MENU MENU
RETURN
ON SCREEN
CH CH
VOLUME
UP
DOWN
TV/VCR
S
T
A
N
D
B
Y
/
O
N
E
N
T
E
R
LIGHT
DVD
RCVR / VCR
T V
CBL / SAT
INPUT
DIMMER
SLEEP
MASTER
VOLUME
PRESET
123
456
789
MEM CLR
0
R
E
P
E
A
T
A
-
B
R
A
N
D
O
M
M
U
T
I
N
G
ENTER
PLAYPLAY
SP A SP B
FM MODE
SURROUND
SP SETUP
IPM
ACOUSTIC
CONTROL
LATE
NIGHT
AUDIO ANGLE
SUBTITLE
ZOOM
SW MODE
T.TONE CH SEL
DISTANCE
PRGV DISCSLOW STEP
RC-
504
M
MODE
–
+
ENTER
--
/
---
SEND/LEARN
M
EN
U
CH
VOLUME
U
P
S
T
A
N
D
B
Y
/
O
N
E
N
T
E
R
LIGHT
DVD
R
CVR / VCR
CBL / SAT
INPUT
DIMMER
SLEEP
M
A
S
T
E
R
V
O
L
U
M
E
PRESET
123
4
5
6
78
9
M
EM
CLR
0
A
-
B
R
A
N
D
O
M
M
U
T
I
N
G
MODE
+
LIGHT
LIGHT
DV
D
RCVR / VC
R
T V
CBL / SAT
DIMMER
SLEEP
C
LR
+
1
2
3
4
5
6
7
8
9
0
2 to 6 inches
(5 to 15 cm)
: Buttons that cannot be programmed.
SEND/LEARN
indicator
MODE
buttons
1
2
3
Programming the commands of remote
controllers for other devices into the
remote controller
When programming the commands of another remote
controller to the RC-504M remote controller, you must first
decide under which MODE button you want the commands to
be linked. In general, you will select the MODE button that
corresponds to the component you are programming.
After programming which MODE button to use, you will then
transfer the separate commands from the other remote
controller over to the RC-504M remote controller one at a
time. Each command is then programmed to a different button
on the RC-504M remote controller. Any button is
programmable for this step except for the four MODE buttons
(DVD, RCVR/VCR, TV, CBL/SAT).
Even after the commands have been memorized, keep your
old remote controller in a safe place. If for some reason the
commands are lost (e.g., when the batteries run down), it will
be necessary to memorize them once again.
Place the remote controller and the
remote controller for the other
device facing each other at a
distance of 2 to 6 inches (5 to 15
cm) apart.
While pressing and holding down
the desired MODE button on the
remote controller, press the ENTER
button and then release both
buttons.
When you press and hold down the MODE
button, the SEND/LEARN indicator lights.
When you press the ENTER button, the
lamp turns off. When you release the
buttons, the lamp lights again.
Press and release the button on the
remote controller which you want to
be programmed.
You may select any button except the
MODE buttons. When you press the
button, the SEND/LEARN indicator turns
off. When you release the button, the
indicator lights again.
If you press the wrong button by mistake,
press that same button again. The SEND/
LEARN indicator flashes twice, and the
remote controller exits the programming
mode.
DVD
RCVR / VCR
T V
CBL / SAT
MODE
ENTER