OPERATING AND INSTALLATION INSTRUCTIONS BUILT-IN VITROCERAMIC HOB
CONTENTS: DESCRIPTION OF THE HOB ........................................................ 27 SAFETY INSTRUCTIONS .............................................................. 28 INSTALLATON ............................................................................... 30 Locating Your Built-in Hob ........................................................... 30 Electrical Connection of Your Hob............................................... 32 USAGE ..........................................................
DESCRIPTION OF THE HOB Dear Customer, It is important that you should read this manual for best performance and to extend the life of your appliance. We recommend you to keep this manual for future reference. Your new hob is guaranteed and will give lasting service. This guarantee is only applicable if the appliance has been installed and operated in accordance with the operating and installation instructions detailed in this manual.
SAFETY INSTRUCTIONS Please comply with these instructions. If you do not, any damage resulting from improper, incorrect or negligent use or improper connection or installation is not covered by the warranty. · This appliance should be used only for normal domestic use. · This appliance must only be used for the purpose of heating or cooking food, any other use, for example heating rooms, working surface or storage surface, is dangerous. · Additions or modifications to the appliance are not permitted.
· Never leave the the appliance hob unattended when cooking with fat or oil . They can rapidly catch fire if overheated. · Do not cut any food on the glass of the vitroceramic hob. Glass panels should not be used as working surfaces. · Be careful when using small household appliances, such as irons, near the elements. · Do not use the cooking zones with empty cookware or without cookware. · Make sure all the controls are in the off position when not in use.
INSTALLATION The electrical connection of this hob should be carried out by an authorised service personal or a qualified electrician, according to the instructions in this guide and in compliance with the current regulations. · Prior to installation, ensure that the local distribution conditions and the adjustment of the appliance are compatible.
· Create an opening with the dimensions shown in the picture below. m 520m 590m m 41mm M 150 in. mm Min. m 25m 560 . Min m 60m mm mm 490 M 130 in. mm · Apply the one-sided self-adhesive sealing tape supplied all the way round the lower edge of the cooking surface along the outer edge of the glass ceramic panel. Do not stretch it. · Screw the 4 worktop mounting brackets on the side walls of product.
Electrical connection of your hob . Before proceeding with the electrical connection, verify that the current carrying capacity of the system and the socket is adequate for the maximum power rating of the hob. · Electrical installation of the residence and the electrical current plug in use must be earthed and conform with safety regulations. · If there is no dedicated hob circuit and fused switch, they must be installed by a qualified electrician before the hob is connected.
2 2 2 * This appliance must be earthed. * For this connetion a power lead of wire type H05V V -F should be used. . For the touch controlled vitroceramic hob, the cable must be H05VV-F 3X2,5 mm² / 60227 IEC 53. You will find the connection diagram shown on the back of your appliance. · During installation, please insure that isolated cables are used. An incorrect connection might damage your appliance. The guarantee will not cover such damages.
USAGE The appliance is operated by touching buttons and the functions are confirmed by displays and acoustic signals. Stand-By-Mode S-Mode Operating-Mode B-Mode The mains are applied to the hob control and all heater displays are off or a residual heat display is active. At least one heater display shows a heat setting between ´0` and ´9` Lock Mode VR-Mode The hob control is locked.
Turn On and Turn Off The Appliance If the appliance is in Stand-By-Mode, it is put in Operating-Mode by pressing the On/Off button at least 1 second. A buzzer signal indicates the successful operation acoustically. On all heaters a ´0` appears and all Decimal Point of the heater flashes (1 sec on, 1 sec off). If there is no operation within 10 sec, the display of all heaters will turn off. If the displays are turned off, the heater will be set into Stand-By-Mode.
Turn on dual and triple zones (available only in some models) Turn on the dual zone The activation of the dual zone is done after selecting the desired heater by actuating . This is confirmed by a buzzer signal. At the same time, the corresponding Dual Zone Indicator goes on statically. Touching for a second time, the status of the dual zone toggles: it changes from dual zone on to dual zone off and back again.
The heat boost can be turned off by pressing until heat setting ´0` appears. If the heat boost should be used, it can always be activated by actuating again if the heat setting is set to level 9. In the heat display ´A/9` flashes. Turn Off Individual Heaters A selective heater can be turned off with 3 different ways: .
Use of timer turn off function for corresponding heater (available only in some models) After reaching a remaining time of 0 minutes, the timer stops the linked heater, showing the ´0` shown in the Heater Display and shuts down Timer Display. In the Timer Display is shown ´00`. The related timer Cooking Zone Indicator disappears. An assigned Dual/Triple Zone Selection Indicator also disappears if it is active. Additionally the buzzer indicates acoustically the timer run out.
Minute Minder No matter whether a heater is activated or not, the minute minder can be operated by touching . The appearing ´00` shows that timer is active and the dot in the right Timer Display indicates that and are now linked for setting the timer value. The minute minder is selected when all Cooking Zone Indicators are statically on or off (no Cooking Zone Indicator is flashing). With and , the timer value can be set.
10 sec after the last operation, the timer display changes to the timer that will run out next. The assignment of that timer is displayed always by a flashing Cooking Zone Indicator. How many timer are running you can identify by the number of Cooking Zone Indicator that are statically on. By toggling , you can display the timer values for the heater timer and the minute minder. The assignment is always indicated by the flashing Cooking Zone Indicator.
If the heater is locked, only can be operated, all other buttons are blocked. If there is any other button operated in the blocked mode, the buzzer signal sounds and the Key Lock Indicator flashes as indication for the activated key lock functionality. Only the switch off by operation of is possible. But if you switched off the appliance, you can not restart it again without unlocking. After pressing 2 sec, the Key Lock Indicator disappears.
The same way the child lock is activated, it can also get deactivated. After pressing until the beep, then the and have to be pressed simultaneously for at least 0,5 sec, followed by touching only the . As a confirmation for successful unlocking, ´L` symbol in the displays will be erased immediately.
TOUCH CONTROL SAFETY FUNCTIONS The following safety functions are available to avoid unintended operations of the hob control. Sensor Safety Cut Off To prevent the appliance from unwanted, random sensor operation, a sensor monitoring is included. In case of one or more buttons are pressed longer than 12 sec, the sensor monitoring routine indicates acoustically that wrong operation (pot or other object placed on the button, sensor failure, etc.) and switches off the appliance.
Over Temperature Switch Off Due to the placement of the control is very close to the heater in the middle front of the hob, it can occur that a not correctly placed pot half on the control and not sensed by the sensor safety cut off (not covering a button) heats up the hob to a very high temperature, which makes the glass and the buttons untouchable without get burned the finger.
Residual Heat Functions After all cooking processes there is some heat stored in the vitroceramic glass called residual heat. The control can calculate roughly how hot the glass is in the worst case. If the calculated temperature is higher than + 60 ° C, then this will be indicated in the corresponding heater display after the heater or the hob control was turned off. The residual heat display is shown as long as the calculated heater temperature is > + 60 ° C.
CLEANING AND CARE Cookware with rough bottoms should not be used since these can scratch the glass ceramic surface. The bottom of the good cookwares should be as thick and flat as possible. Before use, make sure that cookware bottoms are clean and dry. Always place the cookware on the cooking zone before it is switched on. If possible, always place the lids on the cookware.
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
